Yo, this was sick and I been working on mine. After sanding some rough patches here and there, I got the thing work. The issues I kept running through was that the blade never really retract or appear all the way. It somehow alway goes to some area to the blade house or either the slider that seem to be tighter. I try sanding it away but I don't want to take off too much. It worse when I place the rest where I dry test them to see and we'll, it would work. Maybe it was the rubber band I used but even without the cover, i remained back at the root of the problem (I think) where it was tight in the middle, back.
@shadowentertainment9975Ай бұрын
Alright so an update. long story short: it works. But (for me at least) it needs to be modified mostly on the upper portion of the whole thing. The two arms that are with the wheel needed the most of it because the angles (The one that makes the center switch move back and forth whenever you use the string) needed to be beefed up quite a bit, but not so much that it interferes with the slider. The inner walls were also a bit too thin, which made the switch barely even touching the ramps. Luckily this was fixed by adding several cut pieces of thin cardboard (such as cereal box or, what I used, the cardboard portion of a pack of batteries or screws in this case) on both side on the wall where the arms go. Measure and cut them just about the width and height. same thing with the arms, albeit you need to stack them enough. Continue to scrape and sand some layers off from there until it works. It is a bit time consuming, but you'll get there. The second obstacle occurred during a test run. Whenever I put the whole thing together and pull the trigger, it didn't work. I try several times to figure out what was the issue until I found out that the left arm that sit right on top of the slider (The one that activates the blade) keeps popping up. What I meant when I say this was, whenever I pull the string, the arm automatically derails itself from the slider. I later found out that the reason for it was the cover. Turns out it was so thin and flexible that it doesn't have enough strength to keep the arms down, essentially preventing the derailment. This was quickly fixed with some rubber bands on the center, which the issue keeps going over. however, there are better solutions to this, either reinforced the cover, make an entire cover out of wood so that it doesn't flex, or you can edit the file to make it thicker. Hope this helps!
@rafaelmoussa65475 ай бұрын
horrible, how do you record a tutorial video and let your camera to crush and just continue without showing what was lost before?
@cypher86915 ай бұрын
Parts list? ik its pretty simple but still, i wanna get it right
@robertoadrianguerreroochoa5795 ай бұрын
gracias por hacer esto gratis buen tutorial
@EntertainmentLP6 ай бұрын
Watch out this is a complete scam it doesnt work at all this shitbox needs the power times 500 to work it gets out about 2 cm
@KapiEssa227 Жыл бұрын
1:20 what did you do here explain?
@ivanvanko1763 Жыл бұрын
Would this design technically work as a full metal version as well?
@gabrieleelia94719 ай бұрын
Yes
@SolaireAstora-bg6hf Жыл бұрын
Hey, Yoshi I was just wondering were to attach string and ring to please! Love this design a lot thanks!
@mahuhatch2643 Жыл бұрын
LOL deez nuts
@puppy3434 Жыл бұрын
could you please post the part when the camera crashes
@KillJY-fk6oh Жыл бұрын
How do I get this model
@megagamingteen Жыл бұрын
please show what you did when the camera crashed
@megagamingteen Жыл бұрын
I found out how and if i am not wrong the screws are 2 and half mm wide
@endercrafts9056 Жыл бұрын
Great work! I would also like to know whether you came up with the idea for the thing with the rubber band on it that slides back and forth to control the whole blade or you saw it some where else.
@riazuddin1878 Жыл бұрын
how can made assassin gun samelike this
@NoeleVeerod2 жыл бұрын
Interesting design, very similar to the one that Shelden Caudill did, only without the ring. Looks pretty good :)
@raowaqas12732 жыл бұрын
Which 3d software is best u ever used
@indym85233 жыл бұрын
How do you get it to retract?
@AB-lw6eb3 жыл бұрын
what does he do when the camera cashes ???????????????
@itrcks75753 жыл бұрын
Is the ring mechanism working for this?
@mHm2000zt3 жыл бұрын
I did everything as you did.. but still not working at all.. I don't know did I do wrong.. :/
@Arano1373 жыл бұрын
What filament did you use
@AB-lw6eb3 жыл бұрын
PLA
@matteofranciosa22073 жыл бұрын
Dude i just litterally freaking out to assermble the blade cover, because idk how to put back the little pice inside with only the printed thing, the missing part of the crashed camera is not understandable, pls someone can help me, i'm in struggle for two weeks, and re-printed the blade cover like 4 times
@furk4n053 жыл бұрын
i will try to help you
@matteofranciosa22073 жыл бұрын
@@furk4n05 i figured out how to do it, thanks anyway
@shacharbs83 жыл бұрын
@@matteofranciosa2207 can you explain?
@Emi42013 жыл бұрын
@@matteofranciosa2207 EXPLAIN
@Ares-vh9qz2 жыл бұрын
@@furk4n05 how i can do it? i have the same problem
@AntiKipKay3 жыл бұрын
I reworked this entire model. I even made a pla part for the duel extended blade to lock (the part where the camera apparently crashed). I will upload it to thingiverse if there's enough people who are still interested in this design. It works amazingly well in fact it's one of my favorites
@SuperTommy1173 жыл бұрын
Link?
@AntiKipKay3 жыл бұрын
@@SuperTommy117 I'll upload them in a bit and give you a link. What printer do you have?
@SuperTommy1173 жыл бұрын
@@AntiKipKay that would be awesome thank you!! And I have a cr10 s pro v2. Amazing printer in my opinion! :)
@AntiKipKay3 жыл бұрын
@@SuperTommy117 ok here you go www.thingiverse.com/thing:4694383
@AntiKipKay3 жыл бұрын
@@SuperTommy117 Also I only uploaded the files I worked on so you still need to download the rest from the original creator
@rudyperson21533 жыл бұрын
pls respond what size screws did you use i what to make this
@cidlobus3 жыл бұрын
Hola muy buen diseño. Puede ser que la traba de la hoja que lleva un trozo de alambre lleve alguna gomita por dentro? Para que se trabe cuando la hoja se extiende
@mahuhatch2643 Жыл бұрын
nah bro
@somethingdemitri3 жыл бұрын
The one part I can't figure out is the inner blade lock. Please help
@BIANCOBA3 жыл бұрын
Hey i wanted to ask, does the external blade lock? I mean, the first part of the blade. I would like to know because i want to print this one too 😅
@Bang_Pekky3 жыл бұрын
thank you for the file
@ImRafaelPL4 жыл бұрын
what with string
@silverwolf23324 жыл бұрын
Having some struggles assembling the blade as it isn't shown how the hinge works. Do you care to elaborate on that if you're still active?
@rawentury35764 жыл бұрын
Hey buddy ı want the ask something if ı PUT there a Ring and a rope it's can be automatic blade?
@baconpancakes88994 жыл бұрын
And the paper clip? My God, one micro meter out and the whole thing jams
@baconpancakes88994 жыл бұрын
2:50 that piece at the left end is TOO THIN!
@baconpancakes88994 жыл бұрын
My God this is driving the hell out of me from assembling it. You NEED to make the thin parts thicker and please please keep in mind, glue won't withstand the rubber band
@baconpancakes88994 жыл бұрын
I'm 3D printing it right now. I hope I can assemble it properly. Wish me luck.
@BIANCOBA3 жыл бұрын
So, how did it go? I want to print this one too so i wanted to ask if you had any problems or something with this.
@baconpancakes88993 жыл бұрын
@@BIANCOBA Never fully assembled it becuase I couldn't find small rubber bands and the appropriate screws lol
@DEADMANPLAYS3 жыл бұрын
@@baconpancakes8899 lmao 😂😂
@puppy3434 Жыл бұрын
@@baconpancakes8899 Try using loom bands
@SolaireAstora-bg6hf Жыл бұрын
@@baconpancakes8899 The 'loom bands' should work they are very good for blades!
@prometheus86724 жыл бұрын
Does the blade lock?
@joostfly97644 жыл бұрын
can you also use it with like a rope and a ring
@wont_take_it4 жыл бұрын
Hi! Could you upload a video demonstration of the alternate version as well, the one you use a string and a ring to open?
@UNeedDaBeef3 жыл бұрын
You attach a string and ring to the mechanism bruh
@fajriyoesoef74764 жыл бұрын
Is that from shelden Caudill paper hidden blade prototype? I think it similar expecially the spring out and spring in triggerer part
@diy-makingstuff62674 жыл бұрын
My ass yes, the camera crashed rather said that it was a difficult stage and that you were too lazy to film it !! Pfff
@AB-lw6eb3 жыл бұрын
😢😢😢😫 say to him We need you
@floweyn46544 жыл бұрын
this is a double mechanism?
@theGigander1234 жыл бұрын
what did you do that the blocker springs back at 1:22 ? my one dont
@alexkarev21184 жыл бұрын
Did you find the exit in this problem? I dont know how to do it too.
@theGigander1234 жыл бұрын
@@alexkarev2118 ye figured it out. just did a ruberband into the hole and glued it on
@Ares-vh9qz2 жыл бұрын
@@theGigander123 i have the same problem, can you explain better please?
@0c34nT1d34 жыл бұрын
Or at the least subtitles
@alexkarev21184 жыл бұрын
Thanks man.
@rodrigorozotto89374 жыл бұрын
You're the best bro, the brotherhood will always be by you.
@Justin-dv7ul4 жыл бұрын
this is too thin to even 3d print
@Green-The-Mafia4 жыл бұрын
justin zhao wrong. You can print with ever 0.01mm layer heights with 3D printers. Get your facts straight.
@amurotooru2934 жыл бұрын
How long did it actually take you bro ?
@samgossom24394 жыл бұрын
What materials do we need?
@AB-lw6eb3 жыл бұрын
PLA Filament
@allanrec94294 жыл бұрын
What is the nut size
@orfeasgazis18624 жыл бұрын
You could try to make the button one activete from the flexing of the wrist muscle, like described in the game
@sushivision4 жыл бұрын
That mechanism is almost impossible to design.
@AngelCruz-ow1lz3 жыл бұрын
Imdeepainreborn did it, check his youtube channel
@MisticalPineapple4 жыл бұрын
I'm not sure why you made the slider in 2 parts to be glued together. Doesn't printing them in one piece makes the slider stronger? Other than that great video!
@amatiasq5 жыл бұрын
I've been looking at hidden blade desings for 5+ years now. This is the best one by far.
@redcubegamer77164 жыл бұрын
Me too bud
@TheDudeGuy04 жыл бұрын
Same
@Rockyb3034 жыл бұрын
what does he do when the camera cashes tho
@Besecuit4 жыл бұрын
Not really,checkout Rawice's channel
@zeitseele71094 жыл бұрын
kzread.info/dash/bejne/jIKi05OSZ7iaiMo.html how is this? I also have a better more slim one with medieval carves.
Пікірлер
Yo, this was sick and I been working on mine. After sanding some rough patches here and there, I got the thing work. The issues I kept running through was that the blade never really retract or appear all the way. It somehow alway goes to some area to the blade house or either the slider that seem to be tighter. I try sanding it away but I don't want to take off too much. It worse when I place the rest where I dry test them to see and we'll, it would work. Maybe it was the rubber band I used but even without the cover, i remained back at the root of the problem (I think) where it was tight in the middle, back.
Alright so an update. long story short: it works. But (for me at least) it needs to be modified mostly on the upper portion of the whole thing. The two arms that are with the wheel needed the most of it because the angles (The one that makes the center switch move back and forth whenever you use the string) needed to be beefed up quite a bit, but not so much that it interferes with the slider. The inner walls were also a bit too thin, which made the switch barely even touching the ramps. Luckily this was fixed by adding several cut pieces of thin cardboard (such as cereal box or, what I used, the cardboard portion of a pack of batteries or screws in this case) on both side on the wall where the arms go. Measure and cut them just about the width and height. same thing with the arms, albeit you need to stack them enough. Continue to scrape and sand some layers off from there until it works. It is a bit time consuming, but you'll get there. The second obstacle occurred during a test run. Whenever I put the whole thing together and pull the trigger, it didn't work. I try several times to figure out what was the issue until I found out that the left arm that sit right on top of the slider (The one that activates the blade) keeps popping up. What I meant when I say this was, whenever I pull the string, the arm automatically derails itself from the slider. I later found out that the reason for it was the cover. Turns out it was so thin and flexible that it doesn't have enough strength to keep the arms down, essentially preventing the derailment. This was quickly fixed with some rubber bands on the center, which the issue keeps going over. however, there are better solutions to this, either reinforced the cover, make an entire cover out of wood so that it doesn't flex, or you can edit the file to make it thicker. Hope this helps!
horrible, how do you record a tutorial video and let your camera to crush and just continue without showing what was lost before?
Parts list? ik its pretty simple but still, i wanna get it right
gracias por hacer esto gratis buen tutorial
Watch out this is a complete scam it doesnt work at all this shitbox needs the power times 500 to work it gets out about 2 cm
1:20 what did you do here explain?
Would this design technically work as a full metal version as well?
Yes
Hey, Yoshi I was just wondering were to attach string and ring to please! Love this design a lot thanks!
LOL deez nuts
could you please post the part when the camera crashes
How do I get this model
please show what you did when the camera crashed
I found out how and if i am not wrong the screws are 2 and half mm wide
Great work! I would also like to know whether you came up with the idea for the thing with the rubber band on it that slides back and forth to control the whole blade or you saw it some where else.
how can made assassin gun samelike this
Interesting design, very similar to the one that Shelden Caudill did, only without the ring. Looks pretty good :)
Which 3d software is best u ever used
How do you get it to retract?
what does he do when the camera cashes ???????????????
Is the ring mechanism working for this?
I did everything as you did.. but still not working at all.. I don't know did I do wrong.. :/
What filament did you use
PLA
Dude i just litterally freaking out to assermble the blade cover, because idk how to put back the little pice inside with only the printed thing, the missing part of the crashed camera is not understandable, pls someone can help me, i'm in struggle for two weeks, and re-printed the blade cover like 4 times
i will try to help you
@@furk4n05 i figured out how to do it, thanks anyway
@@matteofranciosa2207 can you explain?
@@matteofranciosa2207 EXPLAIN
@@furk4n05 how i can do it? i have the same problem
I reworked this entire model. I even made a pla part for the duel extended blade to lock (the part where the camera apparently crashed). I will upload it to thingiverse if there's enough people who are still interested in this design. It works amazingly well in fact it's one of my favorites
Link?
@@SuperTommy117 I'll upload them in a bit and give you a link. What printer do you have?
@@AntiKipKay that would be awesome thank you!! And I have a cr10 s pro v2. Amazing printer in my opinion! :)
@@SuperTommy117 ok here you go www.thingiverse.com/thing:4694383
@@SuperTommy117 Also I only uploaded the files I worked on so you still need to download the rest from the original creator
pls respond what size screws did you use i what to make this
Hola muy buen diseño. Puede ser que la traba de la hoja que lleva un trozo de alambre lleve alguna gomita por dentro? Para que se trabe cuando la hoja se extiende
nah bro
The one part I can't figure out is the inner blade lock. Please help
Hey i wanted to ask, does the external blade lock? I mean, the first part of the blade. I would like to know because i want to print this one too 😅
thank you for the file
what with string
Having some struggles assembling the blade as it isn't shown how the hinge works. Do you care to elaborate on that if you're still active?
Hey buddy ı want the ask something if ı PUT there a Ring and a rope it's can be automatic blade?
And the paper clip? My God, one micro meter out and the whole thing jams
2:50 that piece at the left end is TOO THIN!
My God this is driving the hell out of me from assembling it. You NEED to make the thin parts thicker and please please keep in mind, glue won't withstand the rubber band
I'm 3D printing it right now. I hope I can assemble it properly. Wish me luck.
So, how did it go? I want to print this one too so i wanted to ask if you had any problems or something with this.
@@BIANCOBA Never fully assembled it becuase I couldn't find small rubber bands and the appropriate screws lol
@@baconpancakes8899 lmao 😂😂
@@baconpancakes8899 Try using loom bands
@@baconpancakes8899 The 'loom bands' should work they are very good for blades!
Does the blade lock?
can you also use it with like a rope and a ring
Hi! Could you upload a video demonstration of the alternate version as well, the one you use a string and a ring to open?
You attach a string and ring to the mechanism bruh
Is that from shelden Caudill paper hidden blade prototype? I think it similar expecially the spring out and spring in triggerer part
My ass yes, the camera crashed rather said that it was a difficult stage and that you were too lazy to film it !! Pfff
😢😢😢😫 say to him We need you
this is a double mechanism?
what did you do that the blocker springs back at 1:22 ? my one dont
Did you find the exit in this problem? I dont know how to do it too.
@@alexkarev2118 ye figured it out. just did a ruberband into the hole and glued it on
@@theGigander123 i have the same problem, can you explain better please?
Or at the least subtitles
Thanks man.
You're the best bro, the brotherhood will always be by you.
this is too thin to even 3d print
justin zhao wrong. You can print with ever 0.01mm layer heights with 3D printers. Get your facts straight.
How long did it actually take you bro ?
What materials do we need?
PLA Filament
What is the nut size
You could try to make the button one activete from the flexing of the wrist muscle, like described in the game
That mechanism is almost impossible to design.
Imdeepainreborn did it, check his youtube channel
I'm not sure why you made the slider in 2 parts to be glued together. Doesn't printing them in one piece makes the slider stronger? Other than that great video!
I've been looking at hidden blade desings for 5+ years now. This is the best one by far.
Me too bud
Same
what does he do when the camera cashes tho
Not really,checkout Rawice's channel
kzread.info/dash/bejne/jIKi05OSZ7iaiMo.html how is this? I also have a better more slim one with medieval carves.