Welcome to Pallet Jackson - your ultimate KZread destination for everything related to pallet jacks! Dive deep into the world of pallet jacks as we unravel their intricacies, parts, and maintenance nuances. From detailed tutorials and expert insights to handy tips, our channel ensures you become a pallet jack pro in no time. But that's not all! Looking for high-quality pallet jack parts and accessories? Visit our online store at PalletJackson.com. Not only do we offer an extensive range of parts, but our interactive pallet jack diagrams guide you to pinpoint exactly what you need. Elevate your knowledge and find top-tier parts only on PalletJackson.com. Subscribe now and be part of our community. 🛒🔧📦
Пікірлер
I have a yale electric pallet jack with error code al06. Works fine goes up and down fwd and back, but then abruptly stops code is on al06 turn key off and on and back to use
AL06 error code can be triggered by 5 conditions related to the motor field and current issues. Here's a summary: *V FIELD NOT OK:* Incorrect voltage at the field connections causes the truck's traction and hydraulic functions to be disabled. Possible causes include loose or damaged cable connections to the motor field, or poor crimps on wires connected to F1 and F2. Verify and secure all connections. *I = 0 EVER:* If motor current levels don't exceed a preset minimum while driving, the truck's traction and hydraulic functions are disabled. Possible causes include damaged or loose electrical connections to the traction motor, low resistance in the traction motor armature (check for shorts), or a damaged controller. Verify connections, check the armature, and if the truck briefly drives but stops with code AL6, replace the controller. *HIGH FIELD CURRENT:* High field current detected by the controller causes the truck's traction and hydraulic functions to be disabled. Possible causes include loose, damaged, or shorted field wires, a shorted or low motor field winding, or a failure of the current sensor in the controller. Check the field wire connections, motor field resistance (around 0.5 ohms), and the controller's current sensor. *NO FIELD CURRENT:* Low field current detected by the controller leads to the truck's traction and hydraulic functions being disabled. Possible causes include loose or damaged cable connections to the motor field, an open or high-resistance motor field winding (should measure ~1.5 ohms), a failed field current sensor or drivers in the controller, or a damaged main contactor circuit. Check connections, measure resistances, and consider replacing the controller if necessary. *STBY I HIGH:* If the controller detects motor current during standby mode, the truck's traction and hydraulic functions are disabled. The likely cause is a damaged controller, which should be replaced. In general, this error disables traction and hydraulic functions, and depending on the condition, loose or damaged connections, motor issues, or a faulty controller are common causes. Replacing or securing connections and possibly replacing the controller are the main steps to resolve it.
please note all these conditions results in flashing the ControllerLED 6 times. We can assist you in one-on-one consultation too. Please reach out to us at [email protected] or call us at (832)239-5393
What type of oil use
This is a hydraulic oil, having a viscosity of 30cSt at 40 °C. The total volume needed is approximately 0.4 litres (ISO VG32).
This video does not teach you ANYTHING... So, to see or know how to do it, you wont get any further here. So, skip it. I just saved you 6 minutes of your time...
Precio de esta herramienta ?
Hi, you can contact our sales representatives for pricing details. Call us at (832)239-5393, or you can email us at [email protected]. We are available Monday to Friday 9am to 6pm EST.
Code e159 ?
Hi, Error e159 in Toyota electric pallet jacks indicates a 'CAN Bus Overrun Error.' This arises due to the TA not replying to CAN messages. You can resolve this error by: 1. Checking for short or open circuits in CAN-bus wiring. 2. Addressing electrical noise by: - Inspecting CAN-bus wiring. - Using a known-good battery. - Driving in a different environment. 3. Check the power amplifier. 4. Check the ETAC. If the issue persists, contact our customer support team for further assistance.
What's the total voltage on this Electric Is palette jack
Hi, thank you for reaching out to us. Could you please specify which electric pallet jack you are referring to? It would be helful to assist you, if you brief your question more precisely.
Error code 40-05 ??
Hi, thank you for reaching out to us. We were unable to locate this particular series of error codes in our database. To provide you with more accurate assistance, could you please specify the model and make of your pallet jack? Additionally, it would also be helpful if you could describe the operational issues you encountered when this error code appears.
But how do the front wheels work?
Hi, thank you for approaching us with your query. The front wheels (commonly referred to as "steer wheels") on pallet jacks are pivoted and connected to a tiller or handle. When the operator moves the tiller left or right, it causes the steer wheels to turn in that direction. This steering mechanism allows for precise control and maneuverability. We'll soon share a detailed video on understanding the front and rear wheels of a pallet jack, briefing their functions and roles. Keep connected! We hope that this will help resolve your query. Thank you again!
but batteries voltaje are 24.1
the error code is 82
in fact I have two of them when I use the "good one" batteries both of them work, when I connect the "bad one" baterries the second has the same behavor . So only the batteries can cause this or there is any circuit with the batteries I need to look at. Thanks you
Thank you for contacting us. Based on the information you have provided, there may be a communication fault originating from the expansion board. We recommend consulting your pallet truck's maintenance manual for an accurate diagnosis of this fault code. However, it is advisable to seek the assistance of a professional service technician in person, as they will be able to thoroughly inspect your equipment and provide appropriate guidance.
great information, I have 8210 does not move or lift it just beep when I push any button do you think the battery set is the problem.
are you a gmt?
Is the seal replacement and the kit the same for a hy lift pallet jack?
Thank you for contacting us. This seal replacement tutorial is specifically followed the Crown PTH model. However, our technical team can also assist with other models, including guidance on seal replacement and kit purchases. Please call us at 832-239-5393 or email at [email protected]. Our hours are Monday to Friday, 9 AM to 6 PM EST.
Really fantastic knowledge respect you sir .
thank you for liking our videos. Feel free to contact us if you need any assistance or pallet jack repair parts. And please subscribe for more helpful content 😊
I have a 2005 Toyota Bt swe120s walkie stacker. Do you guys know what E202 code is?
Thank you for reaching out to us. Error 202 in Toyota electric pallet jack models may be attributed to the TA current sensor error. The underlying cause could potentially stem from a fault in the Phase current sensor. To address this issue, we recommend investigating the cause of the apparent short. Start by examining the cables, and proceed to replace the TA and/or traction motor until the problem is isolated
I need help about jack service
Hi there! Please contact us directly at 1-832-239-5393 or email us at [email protected]!
Awesome
thank you! Please do like, share this video and subscribe to our channel for more insightful content.
Seems your website is down and I need bearings!!
Hi, sorry for the inconvenience. You can check our website now. However, for immediate assistance, you can call us at (832)239-5393.
AMAZING VIDEO!! helped me get a better understanding of what I'm dealing with. I have a jack that the piston does not go down. I already checked the release valve lever and even manually held it and did not go down. I decided to take the hydraulic bolts off. Right now all 3 sections are empty, hydraulic cylinder, Hydraulic pump, and a bolt that was in the bottom by the wheel which I'm assuming is the hydraulic fluid (yes hydraulic came out from this bolt too). Keep in mind the piston is still up high and wont come down. any info helps. THANK YOU!!!
Hi Steven. Thank you for contacting us. Based on the information you have provided, it seems like the main lift ram is bent, and it is stuck inside the unit. Please check it. We hope it will help.
@@PalletJackson Thanks for the info!
In your opinion, which company makes the most reliable electric walkie pallet jacks?
Thanks for reaching out! In my opinion, when it comes to reliability in electric walkie pallet jacks, Toyota and Crown are two companies that consistently stand out. Each company has a strong track record of producing durable and dependable equipment. However, the choice between the two may come down to factors such as specific features, pricing, and after-sales support. I recommend considering your individual needs and comparing the offerings from both Toyota and Crown to make the most informed decision.
I'm sorry Mr. Jackson, I believe the correct terminology to be "ball-peen hammer." Just the same, thank you for uploading. Very helpful.
Hi, thank you for highlighting the terminology. Yeah, you're correct, "ball-peen hammer" is common; however, both terms are used interchangeably. Glad you've found the content helpful!
great info, is the process the same as on your video to add hydraulic fluid to a crown pallet jack?How can i measure the current fluid level without a dip stick
Hi, thank you for contacting us. If your Crown pallet jack doesn't have a dipstick, you can measure the fluid level visually through a sight glass or by observing the level relative to a marked fill line on the reservoir. Another suggestion would be, use a thin wire or a straw. Insert it into the fluid reservoir and mark the wet part. Then, compare it with the recommended level. We have made a detailed video on how you can add hydraulic fluid to your pallet jack. You can check it here: kzread.info/dash/bejne/o5uNx9Z9eMTffMo.html We hope the recommended video will help resolve your queries. Still, if you have any questions, you can email us at [email protected] or call us at 832-239-5393 for a more detailed consultation. We are available 9am to 6pm EST, Monday to Friday.
@@PalletJackson ok great the video does not depict a crown pth though, there is no screw like that on top to fill, I am not sure where to fill the oil
In this case, we recommend you to refer your pallet jack's operating manual. Or reach out to a skilled technician so he can guide you in real time after assessing your equipment's design. Besides, we welcome you to contact our technical customer representative team; they might have a solution to your problem. Thank you!
great video honestly, im always using them at work, was curious how they work
Thank you. Glad you've liked it. Please share and subscribe to get notified of our latest updates. :)
Is a broken cylinder body fixable?
Hey, thank you for contacting us. It depends on the severity of the damage and the cylinder material. In many cases, a broken cylinder body can be repaired through welding or other specialized techniques. If the damage is minimal and doesn't compromise the structural integrity, a skilled technician will be able to weld it. However, if the damage is extensive or if the cylinder is made of a material that doesn't weld well, a complete replacement will be a more practical option. You can call us at 832-239-5393 or email at [email protected] for more detailed consultation. Our business hours are 9am to 6pm EST.