Пікірлер

• 
  @jamesmatthewsjr7400Күн бұрын

  forbidden meat

• 
  @axonedude9167Күн бұрын

  Keep it up 👍

• 
  @axonedude9167Күн бұрын

  Nice job

• 
  @carlosyuda52182 күн бұрын

  Yo perdiendo el tiempo acá.

• 
  @leetheeagle72645 күн бұрын

  How did you make the forge welds stick? I have been trying my darndest to make an axe with a method similar to this, yet no matter what the forgewelds always seem to fail even when I get the steel far hotter than is shown here. Am I missing something?

• 
  @AxlPBlacksmith4 күн бұрын

  Make sure the surfaces of where the weld is gonna be are clean, prevent having any scale on those. Don't forget to use a flux, most people use borax, you can also use sand but that has a lower melting point.

• 
  @leetheeagle72644 күн бұрын

  @@AxlPBlacksmith I see. What kind of cleaning should I give that surface and should I apply the borax immediately after it?

• 
  @AxlPBlacksmith4 күн бұрын

  @@leetheeagle7264 Just grind it smooth and make sure that most of the scale is off, the grit doesnt really matter. Apply borax when the steel is at a red-orange color, wear a mask tho since its nasty stuff( ive gotten really sick from it). When the steel is at like an orange - yellow color, hit the metal a few times to set the weld, then do the actual forgeweld.

• 
  @leetheeagle72644 күн бұрын

  @@AxlPBlacksmith I think I get it, thank you. By the way, this should work in a gas forge too right?

• 
  @AxlPBlacksmith4 күн бұрын

  @@leetheeagle7264 Yeah, i forge with propane.

• 
  @paullark18785 күн бұрын

  Кусок напильника - секрет успешных боевых походов викингов.

• 
  @Little_River_Forge6 күн бұрын

  Getting it done!

• 
  @4wknives6 күн бұрын

  Nice job. I just recently did my first compound grind on a straight razor. It was educational. lol. Did you taper the tail of the blade much? I haven’t gotten to the handle yet on mine.

• 
  @AxlPBlacksmith6 күн бұрын

  The tail on this razor tapers down to 2mm, so half of the thickness of the spine of the blade itself. Don't forget the handle has like a small wedge at the end so the scales are kinda bent and under tension.

• 
  @4wknives6 күн бұрын

  @@AxlPBlacksmith thank you for the answer and tip. I have been a little apprehensive to start the handle. Also a bit busy. But will get it eventually. lol.

• 
  @Mercenary_328 күн бұрын

  Beautiful Knifes! 👍

• 
  @jwdblacksmith182815 күн бұрын

  Very nice

• 
  @Somerandomguy299815 күн бұрын

  That's shark for a knife but dull for a straight razor

• 
  @AxlPBlacksmith15 күн бұрын

  Tell me how you know its dull since it shaved pretty well last time i used it.

• 
  @shawnfeile15 күн бұрын

  As someone who hones straight razors and has forged a couple, he is correct. The edge on a straight razor is so fine cutting paper like you did would destroy the edge. There is a big difference between "razor" sharp for knives and actual razor sharp. You should be tree topping arm hairs, not cutting paper.

• 
  @AxlPBlacksmith14 күн бұрын

  @@shawnfeile Cutting paper is not that good for the edge, sure. But it does not destroy it. The ideal test to see if its sharp is to actually shave with it.

• 
  @Vikingwerk16 күн бұрын

  Well done.

• 
  @derekturner327216 күн бұрын

  BIGTIME shortcut from someone who does razors for a living. Cut your blanks in a diagonal line. The resulting taper if WAY faster to forge into a tail/handle.

• 
  @AxlPBlacksmith16 күн бұрын

  I'll try that out, thanks.

• 
  @bigernbladesmith16 күн бұрын

  Awesome channel.

• 
  @AxlPBlacksmith14 күн бұрын

  Thanks!

• 
  @MASI_forging17 күн бұрын

  Amazing to watch 👍👍

• 
  @heyimamaker19 күн бұрын

  The thing about a straight razor is you never know that you cut yourself until you see the blood 😂 Nice work!

• 
  @jeanladoire414119 күн бұрын

  Nice work FOR A BELGIAN

• 
  @thecrosscloud912719 күн бұрын

  great work, you should get a large magnet and put it on the bottom of the horn of ur anvil, it reduces ringing alot. Could use a welding magnet, I use just a large one from an old large Speaker

• 
  @RyanBarnes16 күн бұрын

  I bought some from harbor freight, they're a little janky, but they reduce the ringing so much!

• 
  @seanstapelfeld20 күн бұрын

  Awesome work!

• 
  @seanstapelfeld20 күн бұрын

  Nice work! Do you mainly do straight razors?

• 
  @AxlPBlacksmith20 күн бұрын

  Not really, this one was my first succeeded attempt.

• 
  @seanstapelfeld20 күн бұрын

  @@AxlPBlacksmith nice great work! So do you usually forge kitchen knives or what is your main thing you forge?

• 
  @AxlPBlacksmith20 күн бұрын

  @@seanstapelfeld Mostly survival knives and historical recreations, i'm currently working on an other video involving wrought iron and carbon steel puukko's.

• 
  @darthsidious48075 ай бұрын

  good job Axl!

• 
  @ForgeDuLys9 ай бұрын

  nice dude ! Cool knife, and the quench was pretty good too, not too hot

• 
  @dvig32619 ай бұрын

  Decent looking knife, where did you buy it? Because that isnt the piece of steel you hacked on...🤨

• 
  @AxlPBlacksmith9 ай бұрын

  I ended up having more material then i was planning on, so i've ground it off. I'll take that as a compliment though, thanks.

• 
  @ForgeDuLys9 ай бұрын

  @dvig3261 yeah you're right, it looks whiter than when he forged it, he's like a mastermind trickster of evil

• 
  @toastyHobo.9 ай бұрын

  Very nice.