Seafarers - Technical Guide for Marine Engineers
--------------------------------------------------------------------------------
Website: www.marinetechhub.com/
RT Flex Engine: sites.google.com/a/devanandts.com/marine-tech-hub-engine/
Nitrogen Generator : nitrogen.devanandts.com/
Solar Power: sites.google.com/a/devanandts.com/solar-power-green-energy/
My Marine Engineering Channel: kzread.info
For Technical Assistance:
Email: [email protected]
Cell No +91 7010035459 (On WhatsApp Only)
Facebook: facebook.com/devanand.sambamurthy
Пікірлер
Hello, i have board am working on and i could use your help. With some small things Please share your mail so we can talk, thank you
Sir
Hii
If there is fault of short circuit without connection of Motor what we should do
Can any one do me a favour and answer me Is there any way to use <UG 8 dial> as a governor of ship engine which is need different speed?
i have a query regarding alborg boiler..actually it is because of the touch screen display showing "comm. error" offline 1..then, i switch to emergency mode, but it doesnt work, i followed the procedure, oil pressure ok, it is igniting but it is not firing at all. there is no indication in the flame scanner that it' s firing..hope you will give me a suggestion regarding this..thank you
there are two flame sensor right?manual and automatic..so what to do is just put the manual sensor to the auto sensor position?vice versa..thanks.😊
Still leaking
Hai plz send your number
Hi.. we are facing an issue with TMC compressor. loading unloading takes placeevery three to four seconds..
hi can you pls tell me how many types of alarms on igs as per solas
Hello sir.....have you ever had a Framo pump shear a shaft once but then a second time a few months later. The pump seems to be OK
Please give contact number
Your phone number not working bro
Burgan .... I think
How can replace programed vfd
hello! i have a problem with donkey boiler Mitsubishi seems like on yor video. My boiler staring and in step 4 (ignition rate set order) of seaquence stuck ((( can you explain which order will be set to become step 5 ?
Frenic 5000g11 power supply fault vfd not power on
thank you for the video. How do you reset the compensation pointer en needle valve after an oil change?
on the same thing sir, can we do this while the main engine is running?i think it will stop the main engine??
Vacon ka lift vfd drive ka out put on off ho raha ha Kia reason ho ga please
nice info thanks for sharing
What's the price of magnetic reed switch
Thanks , very informative.
Sir how to slove err-24 code
A nice and clear explanation of the flex system
Nice job
Drive not on
Bhai Mera output voltage drop ho raha hai kya problem ho sakti hai
sir, what is the reason of placing positive wire of multimeter with negative point of VFD, and then you change by putting negative wire of multimeter with positive point of vfd,,,,pls explain...any reason????
I have trouble with this equipment. After blackout can't ON. Power supply 220VAC is ok. Inside power supply LED is on. Output 24VDC is ok. But inside small display not indicating. The remote controller shows errors for temperature and viscosity.
Please contact me on whatsapp +91 7010035459
Sir how about the valve is not opening in automatic
Stupid video..
Input is ok but out put low byepass is not working give solution
10 KVA LANA HAi. Plaese Cotect. Kere
36kw. Stabilizer how much sir
Super sir
From where I can order this servo stabilizer? Please provide me link, website....
Mujhe bhi repair karwana hai please phone no send kare
For two 1.5 ton ACs, 5 fans, 15 lights, 1 water pump (to fill overhead tank), 1 microwave, 1 refrigerator, 3 led Tvs and 2 desktops. Will 10kva capacity of mainline servo Stabilizer be enough??
35 kva is needed.....LOL.
Thank for sharing!
Remove the fees for all the videos
What the purpose of servo oil motor sir?
very valuable explenation sir, keep up the good work
Hi sir, i would like to know if the drive keyboard is included with the variable frequency drive of Frenic Lifts. I have the same make installed in my home elevator. The technician is asking for extra 15k Rs to replace the board as it was missing.
Hii ,can u send me the pdf please
Send me your contact number pls
When the steam atomizing is activated sir?
Good trouble shooting of capacitor
Your trouble shooting is more educative. Thank you bro