Пікірлер

• 
  @rachaelb916410 күн бұрын

  Thanks

• 
  @RevJenkins1319 күн бұрын

  ok, what is the gadget/press thing you are using?

• 
  @JD-lw3pf2 ай бұрын

  I have not been able to find that tap, is there any way you could put a direct link to it. Greatly appreciated. Thank you

• 
  @truoghv4 ай бұрын

  Hi buddy I have 1 question. How to reduce the temperature of the tap head? *Do not use lubricating oils. :( When working continuously for a period of time, the tap head gets hot, leading to the plastic product melting. Currently I am using compressed air to blow directly into the tap head, but it is ineffective, and too much compressed air is lost.

• 
  @mikeyjay9175 ай бұрын

  To tap you first need to drill a size hole that is known for the tap size you want to use.

• 
  @user-qh1nl2dt3i6 ай бұрын

  Where did you get this exact bit? Cannot find anything but "spiral point"

• 
  @straight_razor10 ай бұрын

  One major problem.. in the majority of cases where the acrylic needs to be tapped, there is no thru-hole. Hence, a gun tap will not work. You should do another video whereby the chips need to be pulled up and out of the hole using a blind hole tap. Many prefer the two flute plug tap however the correct tap is a blind hole spiral tap. The less flutes the better.

• 
  @TropicalEncounter10 ай бұрын

  Thank you! This is exactly what I was looking for!

• 
  @nickverzino322010 ай бұрын

  Great stuff. The link you posted did not take me directly to the tap you used

• 
  @ASKbalrog11 ай бұрын

  Congratulations for the video. would you help me understand which cnc I have to buy, plexiglass and software to use. could you put some links to understand the price/cost. A thousand thanks

• 
  @UMAMITORA Жыл бұрын

  Extremely talented work! I'm interested in your custom work for an SFF build. Is there a way I could have you make a custom reservoir for the front panel hole of the Lian Li x Dan Case A4 H20? Essentially for it to fit right inside the front cut out and able to still install the stock front panel. The dimensions for the cut out are 71.5mm x 152.5mm. If at all possible would only need this reservoir to be about 80ml in total. Referencing the EK FLT 80 reservoir but without a pump and a bit smaller/ cleaner so it'd fit that cut out. Hope to see new content from you!

• 
  @kencoleman7762 Жыл бұрын

  Very useful. Thanks.

• 
  @mikerequadt9661 Жыл бұрын

  Wish had seen this when I tapped some PC with standard tap

• 
  @zmnali78 Жыл бұрын

  really helps, nice research and guide.

• 
  @bryanmoir3184 Жыл бұрын

  What size are you using?

• 
  @jmartinez562 Жыл бұрын

  Excellent video, have been looking the best way to pre-drill cast acrylic for these simple square 12"x 9' bullet Resistance Shields I've been making .... Thank you again!!!

• 
  @norwegianguy Жыл бұрын

  Use oil

• 
  @suntzu6122 Жыл бұрын

  What about a tap that will work when you dont go all the way through?

• 
  @mcbridemotorsports5788 Жыл бұрын

  IMO Thats the only thing I really dislike about my case. I have the original View 71 TG and always felt it should have come with a PSU shroud. Once I bite the bullet and buy a 3D printer I may design one for myself.

• 
  @TheCommo81 Жыл бұрын

  I've threaded plastic and never had that issue. I use 2 flute and do it just like I do metal. It would be better instead of going full-bore through the hole in 1 shot, go 1/2 turn and then back out 1/4 turn. And.....do it with the hand tool, not a press. you'll get clean threads and every time you back out you clean the thread you just made. My taps never get hot but I just take my time. The chips break off and do not compress if you go slow and don't give it a chance to heat up. 2 Flute VS 4 flute gives you more room to clear chips.

• 
  @mikebonello7494 Жыл бұрын

  I don’t understand. I’ve threaded 1000s of pieces of cast acrylic very successfully from M3 to M6 using standard 4 flute taps. Do I back it out yes, do I use a power drill, yes. Do I add a little soap, yes.

• 
  @alexgiebler7905 Жыл бұрын

  I need a shroud for the corsair 760t. Please let me know how I can email about this!!

• 
  @Devistatix8 ай бұрын

  same

• 
  @tpage6550 Жыл бұрын

  Thanks for the video. I noticed that you have machined out a dish in the piece of acrylic. How did you do that? Did you use a router? Thank you

• 
  @lylesnodgrass1961 Жыл бұрын

  Where can I get a drill press like this?

• 
  @sunnieyes Жыл бұрын

  What should i use to drill holes in acrylic leave for jewelry? Should i use the soap for these tiny drills.

• 
  @richardmash7570 Жыл бұрын

  Thank you for this video brother

• 
  @andrebugotti576 Жыл бұрын

  You threading straight through but what if I only want to thread half way through for studs?

• 
  @mjrwey Жыл бұрын

  THANK YOU!!!!!!! Your video beginning it is exactly what was happening when i was trying to tap acrylic!

• 
  @riturajborah382 Жыл бұрын

  Thank you! A gem on youtube!

• 
  @josealberti4571 Жыл бұрын

  what size or what is part #? link doesnt work

• 
  @georgemurdoch1991 Жыл бұрын

  This is fantastic 👏 What is the name for the manual tool that you are using here? Can this be applied to cutting external threads. Thank-you so much for this...

• 
  @SunriseAt2008 Жыл бұрын

  I have the same question ;-)

• 
  @nwembly Жыл бұрын

  I’m case people can’t find it, a gun tap is also referred to as aka “Chip-Clearing Taps”

• 
  @1v1MeBroMW22 жыл бұрын

  If one want's to thread tap into acrylic for a Barrow G1/4 Male Rotary to 90 Degree Female Angle (Fitting for watercooling). Which size thread tapping piece would be used?

• 
  @bobylachanche2 жыл бұрын

  Do you think the threads in acrylic will last long if you screw and unscrew often with a metal screw in it? thanks!

• 
  @andrewmorton96832 жыл бұрын

  You could try melting a brass threaded insert into the plastic.

• 
  @bobylachanche2 жыл бұрын

  Thank!!!!

• 
  @michaelgarn53302 жыл бұрын

  Thank you for your video nobody else has this appreciate it bro

• 
  @Bboynonstop92 жыл бұрын

  Thanks, ordered an m4 bit and did a test hole and seems like it is going to work well.

• 
  @jle52612 жыл бұрын

  Awesome information extremely helpful. Thank you very much

• 
  @brett.c16492 жыл бұрын

  Thanks for saving me the headache

• 
  @PeterWraaeMarino2 жыл бұрын

  thank you so much for this video... was just what I needed.

• 
  @Devistatix2 жыл бұрын

  we spoke a few years ago about making a shroud for my 760t. are you still make these? life happened and the idea kinda got put on the back burner for me, but i'd like to revisit that conversation if possible :)

• 
  @abdelrahmanahmed13132 жыл бұрын

  useless reviwe at least install it

• 
  @Mr1986death2 жыл бұрын

  I see people asking if he still makes this but I don’t see him reply it’s a yes or no answer, for this case and needing one of this but he doesn’t reply so I didn’t ask hopefully he can reply and if money is the issue I don’t mind paying to have one done for me

• 
  @Mr1986death2 жыл бұрын

  I see people asking if he still makes this but I don’t see him reply it’s a yes or no answer, for this case and needing one of this but he doesn’t reply so I didn’t ask hopefully he can reply and if money is the issue I don’t mind paying to have one done for me

• 
  @jameselliott14872 жыл бұрын

  I think it's a good vid. Informative.

• 
  @jameselliott14872 жыл бұрын

  Nice bird

• 
  @plasmaman95922 жыл бұрын

  How deep is the o ring groove? I would like to make my own for my first pc build. This is the first video I came across. I have not checked out the reddit yet

• 
  @plasmaman95922 жыл бұрын

  Never mind. The KZread channel bit-tech has a bunch of videos on how to make them

• 
  @ShopperPlug2 жыл бұрын

  can you make a video showing how to make NPT threads on PTFE or Nylon or ABS plastics?

• 
  @kennuimuffins24262 жыл бұрын

  Very interesting. I wonder how this holds up with smaller threads/sizes. like M3 or M2.

• 
  @electronicsafrica2 жыл бұрын

  thanks! wish i had known about this tap years ago - very useful