Excuse me, I have a question. My ATV BRUTE FORCE 750 has fuel leaking out of the exhaust and apparently it is leaking into the oil.
@user-gl3ql6vv9z7 ай бұрын
Next time u film get more lite on the point of interest and try to hold the camera steady,
@mr.wicked8697 Жыл бұрын
thanks for this bud. wish me luck today
@frankmaio7106 Жыл бұрын
My Brute 750 cranks forever when cold. Any idea if it could be dirty carbs? And thanks for the video.
@nathanwhite5092 жыл бұрын
What do they consider the front carb and what’s considered the rear? They are side by side lol
@MidNebraskaMotorsports2 жыл бұрын
Love your removal video: We have a complete carb rebuild video: kzread.info/dash/bejne/pKOiu9ufY9msdag.html Could I post your video in my video description?
@josearmandorodriguezcortez78042 жыл бұрын
Alguien que me pueda ayudar mi moto es una brute force 750 y no se la numeracion de las espreas de alimentación y las de baja
@mikestowe61362 жыл бұрын
for the time it took ya i would of just bought a slipon exhaust alot less time n hassle
@WTF.4163 жыл бұрын
How did this kit improve your machine? Was there any drawbacks like fuel consumption like excessive fuel consumption LOL
@jbrobertson60523 жыл бұрын
That has got to be the weirdest looking carb I've ever seen lol. I have been pulling wrenches most of my life this is a good video it tells you what you need to know. It told me exactly what I wanted to do and that was I'm going to let someone else to do the job. 😃 Thanks
@popcorn81993 жыл бұрын
Awesome video man thanks!
@zanemerritt90913 жыл бұрын
It I just cut the reducer out will I need to re jet it
@ethanbible52643 жыл бұрын
Well how did it run after you install it any tuning necessary
@montiraruba28313 жыл бұрын
Anyone know where the Serial number/VIN # is located on the Brute Force 750 (2005-2007)?
@dlish26613 жыл бұрын
wish i knew about that before i bought aftermarket exhaust . what kind of tires you running by the way? like that style time to replace mine
@normski2623 жыл бұрын
Any ideas how to remove my seat . Managed to somehow put it on slightly twisted, so the back hooks, one is in correctly, I think, the other is not, release lever is stuck in the up position, and now I cannot get the stupid seat off.
@mitchellowen88213 жыл бұрын
So basically you don’t have a spark arrester is that correct
@jeremysoutherland42903 жыл бұрын
Question, I just bought a 05 brute force 750. The quad idles fine. Once you go quarter throttle it will spit an spitter. Backfire out exhaust. My first thought was jet. Especially since it has a aftermarket exhaust on it . What size jet do I need to install in this thing. Also how many turns should I go in the air fixture screw. Help would be greatly appreciated!
@ranstrickjc3 жыл бұрын
Hey Jeremy, you’re on the right track. If it has an aftermarket exhaust/air intake without jetting it is running lean and that’s why you’re getting the backfire. Check around for kits, and the air/fuel screw are all best chosen based on the altitude you live/ride. Hope this helps!
@stewp.32983 жыл бұрын
Excellent!
@TheUndertoe4 жыл бұрын
Any tunning needed?
@212poncho4 жыл бұрын
I install same kit today on my 07 brute runs strong after gun it after idle It's just wont idle
@eloc801c24 жыл бұрын
I did mine yesterday and I get half rpm an the she falls on her face
@212poncho4 жыл бұрын
@@eloc801c2 what jets u have in it
@WTF.4163 жыл бұрын
Did you figure out why it won’t idle?
@PFothMotor4 жыл бұрын
What did you do to you front bumper to modify it like that?
@okieking85034 жыл бұрын
You dedinitely suck with a camera but I got what I needed lol
@erikdale91454 жыл бұрын
Great work dude thanks
@tylerbrown54894 жыл бұрын
Do you have to rejet it
@JDRTRM5 жыл бұрын
You make a video about an exhaust mod , and show nothing on how it really sounds ?!?!?! I don’t get it ?
@cbrcliff5 жыл бұрын
Did you have to separate the carbs (remove brackets) to remove the float bowls?
@mustangfox302ho5 жыл бұрын
No I wouldn't do it this way either this cause then you might have to resync the carbs
@timber665 жыл бұрын
Nice quad
@chuckloh30085 жыл бұрын
Omg. Worst video ever. Have a headache from u pointing out stuff waving your camera around
@jawsmod6 жыл бұрын
What a PITA just to remove the carb. I need to clean mine on my BF300. Not looking forward to it. After letting it sit it will only run with the choke on.
@ranstrickjc6 жыл бұрын
jawsmod yeah takes a bit but worth it if she isn’t running the best! Best of luck to you and thank you for the comment!
@melvinspencer3766 жыл бұрын
Does this kit come with the new gaskets / o-rings
@stewp.32983 жыл бұрын
No! And it should for the price.
@pablogarza91676 жыл бұрын
Will this work on my 2006 brute force 750?
@ranstrickjc6 жыл бұрын
pablo garza it should, I believe they didn’t change much until around 2008 or so.
@pablogarza91676 жыл бұрын
ranstrickjc okay tomorrow I'm going to start on mine. Hopefully all goes well lol thanks
@cogchildofgod96476 жыл бұрын
Your camera just moves too much to watch
@ranstrickjc6 жыл бұрын
Hammerhead Chiseltooth yeah sorry about that, was just my cell phone.
@joanrodriguez58486 жыл бұрын
What was the mods on this bike? Or was it bone stock?
@sourandthebigbigger95606 жыл бұрын
Did this kit make a difference
@ranstrickjc6 жыл бұрын
Anythingwithremotes made a huge difference, bike came to life!
@kenwoolner86066 жыл бұрын
Sounds awesome with that vtwin
@ginochipchip6 жыл бұрын
wow thats nuts how you liking you tires in the deep snow ?
@6sigmajetkit6 жыл бұрын
Great Video. Here is the link that the viewers were looking for: www.6sigmajetkit.com/
@dirtbikeboy81697 жыл бұрын
did u get exhaust on yet
@RYANHODGE1007 жыл бұрын
Hi, what's the part number for the carb boots? Is it #16065? And where did you order from?
@ranstrickjc6 жыл бұрын
Ryan Noel-Hodge I’m honestly not sure it’s been a while since I did this repair. MRCycles is where I ordered them from I believe. Just type in the info for your year and it should show you which one you need. They were under $10 pretty sure. Hope this helps!
@ovalmechanic7 жыл бұрын
would you recommend doing this for a clogged muffler? im thinking just the silencer is clogged because nothing else can get clogged
@korbynkolton79692 жыл бұрын
you prolly dont give a shit but does someone know a tool to get back into an Instagram account? I was dumb forgot my account password. I would appreciate any help you can offer me!
@graysonquinn50172 жыл бұрын
@Korbyn Kolton Instablaster =)
@rollon39017 жыл бұрын
CAUTION,, do not use a 5/32 drill in the slide. The slide relief hole should be drilled with a #49 drill, or .073. 5/32 is way to big and not recommended.
@639Beaver7 жыл бұрын
camera shakes too mucj
@ranstrickjc6 жыл бұрын
Walter B yeah sorry about that, was recorded with my cell phone at the time.
@python357magnum1007 жыл бұрын
Japanese Phillips is different than all others, JIS (Japanese Industrial Standard) getting some of those bits or screw drives would help on not stripping them out. I have a 06 Arctic Cat with that engine,not looking forward to taking the carbs off.
@tacomafan74888 жыл бұрын
last question! if i dont 're jet it back fire how bad is for the engine? Sorry i dont know much about small engines. Thanks
@markalan40262 жыл бұрын
Whenever opening up additional airflow by modifying the exhaust and/or air intake it causes a lean air/fuel ratio. In order to correct this you must rejet the carburetors, or remap the fuel system with an EFI setup. Running an engine lean is not good and over time will cause damage. Also, you will not gain additional power simply by opening up air flow, you must add additional fuel as well.
@tacomafan74888 жыл бұрын
thanks for advise.
@tacomafan74888 жыл бұрын
good job!. i never done anything like that. im kind of afraid to go that deep inside.
@tacomafan74888 жыл бұрын
ok. do i have to 're jet if i do the same? if yes why?
@ranstrickjc8 жыл бұрын
I would recommend doing this only if you upgrade the stock air filter and jet. The reason is because all those things change the air to fuel ratio. Adding exhaust mods increase air flow and if you don't jet your bike will run lean and have some serious backfire problems.
@tacomafan74888 жыл бұрын
how long did it take you to install this kit?
@ranstrickjc8 жыл бұрын
Hey Mike, I want to say it took me around two hours or so from start to finish.
@tacomafan74888 жыл бұрын
did you use aluminum welding for this exhaust?
@ranstrickjc8 жыл бұрын
The stock pipe is made of steel so regular welds are the ticket. Used a wire feed.
Пікірлер
Excuse me, I have a question. My ATV BRUTE FORCE 750 has fuel leaking out of the exhaust and apparently it is leaking into the oil.
Next time u film get more lite on the point of interest and try to hold the camera steady,
thanks for this bud. wish me luck today
My Brute 750 cranks forever when cold. Any idea if it could be dirty carbs? And thanks for the video.
What do they consider the front carb and what’s considered the rear? They are side by side lol
Love your removal video: We have a complete carb rebuild video: kzread.info/dash/bejne/pKOiu9ufY9msdag.html Could I post your video in my video description?
Alguien que me pueda ayudar mi moto es una brute force 750 y no se la numeracion de las espreas de alimentación y las de baja
for the time it took ya i would of just bought a slipon exhaust alot less time n hassle
How did this kit improve your machine? Was there any drawbacks like fuel consumption like excessive fuel consumption LOL
That has got to be the weirdest looking carb I've ever seen lol. I have been pulling wrenches most of my life this is a good video it tells you what you need to know. It told me exactly what I wanted to do and that was I'm going to let someone else to do the job. 😃 Thanks
Awesome video man thanks!
It I just cut the reducer out will I need to re jet it
Well how did it run after you install it any tuning necessary
Anyone know where the Serial number/VIN # is located on the Brute Force 750 (2005-2007)?
wish i knew about that before i bought aftermarket exhaust . what kind of tires you running by the way? like that style time to replace mine
Any ideas how to remove my seat . Managed to somehow put it on slightly twisted, so the back hooks, one is in correctly, I think, the other is not, release lever is stuck in the up position, and now I cannot get the stupid seat off.
So basically you don’t have a spark arrester is that correct
Question, I just bought a 05 brute force 750. The quad idles fine. Once you go quarter throttle it will spit an spitter. Backfire out exhaust. My first thought was jet. Especially since it has a aftermarket exhaust on it . What size jet do I need to install in this thing. Also how many turns should I go in the air fixture screw. Help would be greatly appreciated!
Hey Jeremy, you’re on the right track. If it has an aftermarket exhaust/air intake without jetting it is running lean and that’s why you’re getting the backfire. Check around for kits, and the air/fuel screw are all best chosen based on the altitude you live/ride. Hope this helps!
Excellent!
Any tunning needed?
I install same kit today on my 07 brute runs strong after gun it after idle It's just wont idle
I did mine yesterday and I get half rpm an the she falls on her face
@@eloc801c2 what jets u have in it
Did you figure out why it won’t idle?
What did you do to you front bumper to modify it like that?
You dedinitely suck with a camera but I got what I needed lol
Great work dude thanks
Do you have to rejet it
You make a video about an exhaust mod , and show nothing on how it really sounds ?!?!?! I don’t get it ?
Did you have to separate the carbs (remove brackets) to remove the float bowls?
No I wouldn't do it this way either this cause then you might have to resync the carbs
Nice quad
Omg. Worst video ever. Have a headache from u pointing out stuff waving your camera around
What a PITA just to remove the carb. I need to clean mine on my BF300. Not looking forward to it. After letting it sit it will only run with the choke on.
jawsmod yeah takes a bit but worth it if she isn’t running the best! Best of luck to you and thank you for the comment!
Does this kit come with the new gaskets / o-rings
No! And it should for the price.
Will this work on my 2006 brute force 750?
pablo garza it should, I believe they didn’t change much until around 2008 or so.
ranstrickjc okay tomorrow I'm going to start on mine. Hopefully all goes well lol thanks
Your camera just moves too much to watch
Hammerhead Chiseltooth yeah sorry about that, was just my cell phone.
What was the mods on this bike? Or was it bone stock?
Did this kit make a difference
Anythingwithremotes made a huge difference, bike came to life!
Sounds awesome with that vtwin
wow thats nuts how you liking you tires in the deep snow ?
Great Video. Here is the link that the viewers were looking for: www.6sigmajetkit.com/
did u get exhaust on yet
Hi, what's the part number for the carb boots? Is it #16065? And where did you order from?
Ryan Noel-Hodge I’m honestly not sure it’s been a while since I did this repair. MRCycles is where I ordered them from I believe. Just type in the info for your year and it should show you which one you need. They were under $10 pretty sure. Hope this helps!
would you recommend doing this for a clogged muffler? im thinking just the silencer is clogged because nothing else can get clogged
you prolly dont give a shit but does someone know a tool to get back into an Instagram account? I was dumb forgot my account password. I would appreciate any help you can offer me!
@Korbyn Kolton Instablaster =)
CAUTION,, do not use a 5/32 drill in the slide. The slide relief hole should be drilled with a #49 drill, or .073. 5/32 is way to big and not recommended.
camera shakes too mucj
Walter B yeah sorry about that, was recorded with my cell phone at the time.
Japanese Phillips is different than all others, JIS (Japanese Industrial Standard) getting some of those bits or screw drives would help on not stripping them out. I have a 06 Arctic Cat with that engine,not looking forward to taking the carbs off.
last question! if i dont 're jet it back fire how bad is for the engine? Sorry i dont know much about small engines. Thanks
Whenever opening up additional airflow by modifying the exhaust and/or air intake it causes a lean air/fuel ratio. In order to correct this you must rejet the carburetors, or remap the fuel system with an EFI setup. Running an engine lean is not good and over time will cause damage. Also, you will not gain additional power simply by opening up air flow, you must add additional fuel as well.
thanks for advise.
good job!. i never done anything like that. im kind of afraid to go that deep inside.
ok. do i have to 're jet if i do the same? if yes why?
I would recommend doing this only if you upgrade the stock air filter and jet. The reason is because all those things change the air to fuel ratio. Adding exhaust mods increase air flow and if you don't jet your bike will run lean and have some serious backfire problems.
how long did it take you to install this kit?
Hey Mike, I want to say it took me around two hours or so from start to finish.
did you use aluminum welding for this exhaust?
The stock pipe is made of steel so regular welds are the ticket. Used a wire feed.