Wireless Engineer CCNP CWNE 51 - Interested in RFID Wi-Fi MESH technology and art.
This collection of video uploads is quite random. I may upload a technical training video and then follow it up with a video capture of a cool old bridge I drove over. You never know what I might upload.
Пікірлер
What a great show it was!
Absolutely! :D
The picture may be a tad fuzzy but it's an absolute joy to hear the three bass-players so clearly.
I know it's fuzzy :( my puny little dashcam isn't up to the task. If I were more prepared, I would've had a nice new phone with enough storage to shoot 4k, but alas...
@@JenniferLucille I watched your video in full screen mode and I think it's fine. There is some glare caused by the bare light bulbs pulsating all over the stage, but I don't know if a better camera would have made a difference. Of the two videos of this show currently on KZread, yours is the best by far. There are very few videos where you can hear Danny's bass so clearly. Thanks for posting!
@@aquaritone9541 Yeah, the fluctuating lighting was a lot for my little dash cam to handle. The upside of this is, it gave me the motivation to upgrade my current dashcam. My next Twigs video will look a lot better as a result :D
OMG THANK U SO MUCH!
Question. At the 4 min mark, it shows a piece of cardboard tapped over the circuit board. Is this there all the time to keep the dust out? And you’ve had no problems with it?
I put that over the electronics when I was doing some engraving/scoring on plaster of paris pieces to keep any dust off the electronics. I made sure that the cardboard clears all the moving parts and no, I haven't had any problems with it being in place :)
Do you have a video of attaching the red wire to the glowforge? I have it all taken apart and my new red wire ready, but I do not know the next step. thank you
On my Glowforge, the red wire on the left side (away from the on button) is permanently attached into the power supply. I cut the red wire at the place where it shorted, put the splice kit in line and then ran the wire around the back of the glass tube as shown in this video. The right hand side of the wire (the side where the ON button is located) will have a ring terminal attached to it from the Glowforge factory. That ring terminal screws into the end of the glass laser tube. You have to remove the red silicone cap off of the right side of your laser to get at this screw. It is a 10m hexhead screw. Here is a link to the video I started with kzread.info/dash/bejne/pJiirdmakcjRhLw.html&pp=ygUSZ2xvd2ZvcmdlIHJlZCB3aXJl
The whole blog post I made with extra pictures and links to everything is here jenniferhuber.blogspot.com/2024/06/splicing-red-wire-on-your-glowforge.html
Did you ever think when you started hanging out together "it's going to get weird now isn't it?"
Thanks, still totally worked on review of properties. If you zoom in you can get a more pinpoint selection.
I was there in the front row!!
Thanks for helping me in 2023 ❤️
I’m off to see this performance at the end of this month in Melbourne. Thanks for uploading
I'm gonna see this in NZ in 2 days!!!
Hey Jen, this is great content. Still relevant 12 years later to CPI. Many thanks for posting.
Oookay so where are the videos to show how to make one?
There's a link to a blog post I wrote about how to make one. Chock full of measurements etc. :)
I want you to meet my mother.
No comments yet?! Thanks for the upload; this is great stuff!
Hello Jannifer If you click the option of use GPS if¡t will make the surb¡veys a little bit easier? And my other question is so when you start to walk through the site are you scanning, every move that make (change direction) you need to click on the map and drag the mouse everytime you are walking?
Don’t worry I have a comment
Love this! Thanks for recording and posting
No comments yet Say something to start the conversation
Thanks for sharing!
OH MY HECK! That was so great!
You make many great things possible! We owe it all to you for your creative vision and the masterpiece of Rubin and Ed. <3
Thank you very much Jennifer !! Idid not know that this tool even existed. You gave me a lot of information very clearly. I am sure that this information will help in a complex interference scenario that I am dealing with in my work. I have an Rohde&Scwarz spectrum analyzer but I only can see de frequency occupation and I can´t determinate the source or sources of interference, especially when there multiple devices that can be that source.
Tyvm for this! Love Wet Leg!
You're so welcome! & me too! :D
Great live concert & video caption jennifer 🎶
Thank you for the kind words!
Thanks Jennifer…. From the Mickey Mouse T Shirt dude!!!!
:D Thank you!
Very nice, thanks for sharing
Thank you! Cheers!
happy cat ride :)
Wow!
Fred Lane is the apotheosis of human evolution. He controls the toll booth to Dwight Eisenhower.
Got you. So basically the whole differences here are 'compatibility' issue. Like for example, BLE can only transmit frequencies between 'registered' devices or terminals, if not, no matter how close beacons fall into the frequency range, they won't interact. Just like a neighbor next door can't connect my Air pods to his smart phone, because it's not registered. Whereas RFID as long as two 'things' are tagged, they all interact each other within the given range. NFC, basically a fancy barcode. lol Thanx
How did you get the shoe?
One of the greatest movies ever.
You got the knock-knee dance down pat with him! Good job!
My Cat can eat a whole Watermelon.
Great 👍👍
Hello Jennifer , I have a cisco air-cap3502i-a-k9. I want to configure it as an access point . Could you give me the steps to configure it . Thanks for all
Cisco has lots of configuration examples here: www.cisco.com/c/en/us/support/wireless/aironet-3500-series/products-configuration-examples-list.html & this youtube video should help as well kzread.info/dash/bejne/c6upudWAd9LMhJc.html
Success!!!!!!!! You are the king of the echo ppl! Lol
I can't tell you how happy this and having the puppet make me!!
Much better now with latest smartphones
That was incredible. Thank you Jennifer
Hi Jennifer, That's interesting. Jennifer, are you going to share some experience with mesh design/deployments. I am studying for the CCNP wireless design exam and I struggle to understand how these network are commonly deployed (e.g. daisy chaining? Single chanel?).
9 years later, and still a super-underrated video! Thank you for sharing!
Thanks!! I couldn't believe how easy it was BUT how hidden the feature is. :D
Thank you both for this very enjoyable video and music. This is how I like to see improvised music: Without borders! A pleasure to watch!
amzaing,it has helped me a lot thanks
I find your videos very interesting.Thanks. Do you still use this application or you found something better? I see the last update for this software was released 4-5 years ago. It would be nice if you could share similar videos about your field experience.
The Cisco Spectrum Expert hasn't existed for many, many years. The ways you view spectrum nowadays is with Ekahau, Tamosoft, AirMagnet etc.
wow , good