How much did it cost ya to build the full tray? Looking at doing something similar.
@__z4ne__823Күн бұрын
Yo where did you get the mirrors from
@anythingautoimports95505 күн бұрын
Nice one Hayden, good to see the JetSki cradle put to good use with the leaf springs (I’m assuming that’s what it was). Well explained. Great inspo for my next build.
@HaydnKamp3 күн бұрын
Thanks! Yeah sure is! Makes for a great leaf spring holder 😅
@half_ass_gaming98649 күн бұрын
Do you reckon these mods will work for a dual cab with roof rack roof top camper draws ?? 😅
@HaydnKamp7 күн бұрын
Absolutely no doubt, just need more leaves 🤘🏻
@kano86_4x4_explore11 күн бұрын
Been hitting up glasshouse a bit lately just don't know where to find all these tracks at
@HaydnKamp7 күн бұрын
Have you tried newtracks the phone app. Could help you find some tracks
@AnthonyPepper-x6x13 күн бұрын
Nice build mate, what sort of paint did you use ?
@HaydnKamp7 күн бұрын
White knight rust guard epoxy enamel in satin black
@AnthonyPepper-x6x5 күн бұрын
Sweet mate exactly what I bought , looks good mate 👍🏽
@HaydnKampКүн бұрын
@@AnthonyPepper-x6x easy to spray and easy to touch up too
@AnthonyPepper-x6xКүн бұрын
@@HaydnKamp yeah that’s it mate I got a couple runs but I’ll just wait till it’s dry and give them a light sand and touch up 👍🏽
@AnthonyPepper-x6x13 күн бұрын
Nice build mate, what sort of paint did you use ?
@HaydnKamp3 күн бұрын
WhiteKnight Rust guard epoxy enamel in satin black
@Huddo17914 күн бұрын
How much of a lift have you got on it to run the 35’s
@HaydnKamp7 күн бұрын
2-3inch however suspension lift doesn’t help clear tyres. Its locating the wheels in the wheel arch best as possible, removing material when the tyre rubs and limiting up travel that clears the 35’s
@TheDeansAroundOz15 күн бұрын
Ive just got myself an RN105 that has been engine swapped with a commodore V6 ecotec engine, has had some work done to the suspension, cant wait to get it up to spec and get it out on the tracks. It is a project truck for my two boys and I. Love the old HiLux's
@HaydnKamp7 күн бұрын
They are bloody great Utes and a lot of fun 🤘🏻
@TheDeansAroundOz4 күн бұрын
@@HaydnKamp been great so far, just chasing some electrical gremlins from engine conversion atm.
@HaydnKampКүн бұрын
@@TheDeansAroundOz yeah that’s no fun
@CarSpec3916 күн бұрын
Should do a coil conversion in the rear, love the videos
@HaydnKamp7 күн бұрын
Cheers man! I like the simplicity of leaves
@CarSpec397 күн бұрын
Yeah, that's an upside, u still got good flex out of the rear
@coreyhaury16 күн бұрын
Awesome video man. It is giving me ideas on how to build mine. What tail lights are you using?
@HaydnKamp7 күн бұрын
Thanks mate!! Maxilamp 355’a
@rampagearms666919 күн бұрын
What tail lights are those, they look amazing
@HaydnKamp18 күн бұрын
Maxilamp 355’s
@rampagearms666918 күн бұрын
Thankyou for the reply, I'm from the US and I can't find that style anywhere so I really appreciate it alot
@HaydnKamp17 күн бұрын
@@rampagearms6669 no problem at all
@DanielLegaspivlogs20 күн бұрын
What's your gear ratio?
@HaydnKamp18 күн бұрын
4.3 diff ratio and trailgear reduction gearset in t case
@giorgiweibolt787723 күн бұрын
he was tightening the u bolt
@Trippety25 күн бұрын
Need new RN content🥺🥺
@HaydnKamp24 күн бұрын
Not on the cards unfortunately man 😢
@fistedfpv292225 күн бұрын
wish i never sold my LN
@HaydnKamp24 күн бұрын
I wish I didn’t have to sell it either 😢
@user-dx6ex3vb4h25 күн бұрын
Your rige looks amazing 🤙🤙
@HaydnKamp24 күн бұрын
Cheers man!!
@NathanielNoye-hm2bz25 күн бұрын
Nice car video
@HaydnKamp24 күн бұрын
Thanks mate!
@ismailziar605925 күн бұрын
Does Ln106 come in 1990 or 1994, I have searched In Many webs it result is 1990 year. Can You give me some info about that
@Cicada4WD25 күн бұрын
Tough
@HaydnKamp24 күн бұрын
Too clean now 😅
@fordy65525 күн бұрын
Did you tig or mig
@Trippety25 күн бұрын
Mig
@HaydnKamp24 күн бұрын
Mig
@Mulletboibenny28 күн бұрын
1996 model I have the same one
@HaydnKamp24 күн бұрын
The best 🤘🏻
@Mulletboibenny24 күн бұрын
@@HaydnKamp yeah
@lidltraut8258Ай бұрын
I like that you can see that the car is actually used quite a bit and that the mods really make sense
@HaydnKamp24 күн бұрын
Needs to get used more 😅
@LeoReemanАй бұрын
Will this work in a LN167 (IFS) what will I need in the front ?
@HaydnKamp24 күн бұрын
I haven’t had much to do with torsion bar ifs front ends sorry man
@harrywoodow18Ай бұрын
Hi There is there anywhere online you can buy the long slip drive shafts from?
@jarheadmarine5655Ай бұрын
I wish this video was in english
@locklyntogo4561Ай бұрын
Hey mate love watching you and I'm gonna build my own tray for my ln106 and love your design and I was gonna try and match yours but a little bit longer and wanted to know the measurements of the rear part from the side to first angle cut on each side
@AlexAftabXcАй бұрын
I need this stock sir I like this cars can you send me details and contact information
@IdopaintingАй бұрын
What did you paint the tray in what products for the undercoat and final coat ?
@HaydnKampАй бұрын
Just used White knight rust guard epoxy enamel in satin black. Majority I didn’t prime
@IdopaintingАй бұрын
@@HaydnKamp oh yeah looks sick luv the build, thanks 👍
@jimbo4014Ай бұрын
Saw the other ln on market place
@HaydnKampАй бұрын
Yeah ended up having to sell it unfortunately man
@mickosmith113Ай бұрын
Hey mate Question for you Would these rear leaf springs fit a duel cab ?
@HaydnKampАй бұрын
Yeah sure would Micko
@mickosmith113Ай бұрын
Another question man I’ve already got 2inch straight shackles in the front would they work or do I definitely need the banana shackles?
@olivergoodlace9521Ай бұрын
How do I know where to weld the mounts and what do I do to make mounts to fit onto the chassis. Can you show that
@HaydnKampАй бұрын
Have a look at the full length video man, should have the answers your looking for
@SkeeDaddle-mh7yx2 ай бұрын
Hey mate, what other front shocks would you recommend if i wanted to safely do beach runs and highway driving with this setup?
@HaydnKampАй бұрын
Superiour do a range for the hilux that are decent for the money. Open - Closed / Lift / Travel mm/inch 605 -370mm / 5inch / 235/9.2 565 - 350mm / 4inch /215/8.4 535- 335mm / 3inch / 200/7.8
@michellecharman2222 ай бұрын
Patrol
@HaydnKampАй бұрын
Patrol drivers would have too much foot twitch to drive up the wall. Or they’d hit it in 2nd head on trying to ‘bump’ it🤣🤣
@brandonar8682 ай бұрын
A DashMat is essential for protection from Sun Cracked Plastic...Are you a Clown?
@JustDreamChasing2 ай бұрын
In the USA. Love the lights! I’m trying to get ideas for a flat bed build and this is probably my favorite ones so far. Where did you find the lights?
@HaydnKampАй бұрын
A company called LED auto lights make them. Maxilamp series
@JustDreamChasingАй бұрын
Thank you. Awesome build. Looks so good.
@mitchellwhiting12952 ай бұрын
What a bunch of rigs!!
@HaydnKamp2 ай бұрын
Peak hilux goals 😅
@smsd7772 ай бұрын
Great work mate! I’ve been putting off finishing my 89 IFS 4Runner in the hope of going full three link/ coilovers with SAS but this has me thinking differently 😊
@HaydnKamp2 ай бұрын
Cheers mate! Leaf springs do impressive things when set right 🤘🏻
@smsd7772 ай бұрын
@@HaydnKamp thoughts on ladder bar to reduce long leaf axle wrap in the back?
@HaydnKampАй бұрын
Would definitely help, I haven’t bothered as it doesn’t seem to be an issue with 80hp 🤣
@hardlydavidson19372 ай бұрын
Hi Hayden, when's your next video coming out?
@HaydnKamp2 ай бұрын
Unsure man, I’ve had to sell the RN so this little series is no more unfortunately
@hardlydavidson19372 ай бұрын
@@HaydnKamp that's a bummer.
@UralUazMan2 ай бұрын
🫠👍👍👌🤙
@apboxes2 ай бұрын
😈😈😈
@dgiobun2 ай бұрын
A top build. Got a LN 167 double cab. Really inspired me to build one.
@HaydnKamp2 ай бұрын
Cheers man! Get after it, great project building a tray 🤘🏻
@b.s.adventures94212 ай бұрын
Like the cheap simple mods using a bag of mixed oem parts. That’s the roots of hot rodding too.
@HaydnKamp2 ай бұрын
If it works it works hey!
@joelseconi2 ай бұрын
just wondering mate how much did all of this set you back $
@HaydnKamp2 ай бұрын
Roughly around $1,000 Joel
@user-bd1tf1gt4c2 ай бұрын
would u ever consider building another one of these
@HaydnKamp2 ай бұрын
I tried recently but ran out of money and had to sell it 🤣
@HoangNguyen-vf7me2 ай бұрын
Bloody awesome mate! Can i ask what welding machine you are using?
@HaydnKampАй бұрын
Unimig viper 250, about 7 year old
@mickosmith1132 ай бұрын
Great video mate You done well .. I’ve got a old LN scrubbing 305x75 16 s on the front guards 🙄 So il be looking at doing this for sure 👍
@HaydnKamp2 ай бұрын
Thanks mate! This will sort that issue out for ya 🤘🏻
@Mac-bn2 ай бұрын
I have ordered one. While driving to the foggy mountains on cold and raining it was good and happy with it. Upon my return home the next day I found there is a condensation building up from end to end. I look at KZread how to remove the water vapour. Remove the valve. On the light for 30min close the valve and off the light. But it doesn't work. I take picture and email to Auxbeam asking how to prevent or remove the water vapour. Their reply was they seeking advice to their technical but till today no news. This is the first and last for me with Auxbeam.
@Mac-bn2 ай бұрын
After posting this. In the evening I received their email and they are sending a new light bar same model as replacement. If this is the case they held responsibility and guarantee to replace I will continue to use Auxbeam. Thank you Auxbeam
@jamesdurie53122 ай бұрын
What a great video! Keep it up. Ive been wanting to do this to my ute for a while now. Just wondering how long do the breaklines has to be and what degree caster wedges would you recommend? 💪💪
@AhilMohan2 ай бұрын
heavy duty
@HaydnKamp2 ай бұрын
It’s still holding up great 🤘🏻
@AhilMohan2 ай бұрын
@@HaydnKamp The lines, especially the rear end with the lights look sex
Пікірлер
How much did it cost ya to build the full tray? Looking at doing something similar.
Yo where did you get the mirrors from
Nice one Hayden, good to see the JetSki cradle put to good use with the leaf springs (I’m assuming that’s what it was). Well explained. Great inspo for my next build.
Thanks! Yeah sure is! Makes for a great leaf spring holder 😅
Do you reckon these mods will work for a dual cab with roof rack roof top camper draws ?? 😅
Absolutely no doubt, just need more leaves 🤘🏻
Been hitting up glasshouse a bit lately just don't know where to find all these tracks at
Have you tried newtracks the phone app. Could help you find some tracks
Nice build mate, what sort of paint did you use ?
White knight rust guard epoxy enamel in satin black
Sweet mate exactly what I bought , looks good mate 👍🏽
@@AnthonyPepper-x6x easy to spray and easy to touch up too
@@HaydnKamp yeah that’s it mate I got a couple runs but I’ll just wait till it’s dry and give them a light sand and touch up 👍🏽
Nice build mate, what sort of paint did you use ?
WhiteKnight Rust guard epoxy enamel in satin black
How much of a lift have you got on it to run the 35’s
2-3inch however suspension lift doesn’t help clear tyres. Its locating the wheels in the wheel arch best as possible, removing material when the tyre rubs and limiting up travel that clears the 35’s
Ive just got myself an RN105 that has been engine swapped with a commodore V6 ecotec engine, has had some work done to the suspension, cant wait to get it up to spec and get it out on the tracks. It is a project truck for my two boys and I. Love the old HiLux's
They are bloody great Utes and a lot of fun 🤘🏻
@@HaydnKamp been great so far, just chasing some electrical gremlins from engine conversion atm.
@@TheDeansAroundOz yeah that’s no fun
Should do a coil conversion in the rear, love the videos
Cheers man! I like the simplicity of leaves
Yeah, that's an upside, u still got good flex out of the rear
Awesome video man. It is giving me ideas on how to build mine. What tail lights are you using?
Thanks mate!! Maxilamp 355’a
What tail lights are those, they look amazing
Maxilamp 355’s
Thankyou for the reply, I'm from the US and I can't find that style anywhere so I really appreciate it alot
@@rampagearms6669 no problem at all
What's your gear ratio?
4.3 diff ratio and trailgear reduction gearset in t case
he was tightening the u bolt
Need new RN content🥺🥺
Not on the cards unfortunately man 😢
wish i never sold my LN
I wish I didn’t have to sell it either 😢
Your rige looks amazing 🤙🤙
Cheers man!!
Nice car video
Thanks mate!
Does Ln106 come in 1990 or 1994, I have searched In Many webs it result is 1990 year. Can You give me some info about that
Tough
Too clean now 😅
Did you tig or mig
Mig
Mig
1996 model I have the same one
The best 🤘🏻
@@HaydnKamp yeah
I like that you can see that the car is actually used quite a bit and that the mods really make sense
Needs to get used more 😅
Will this work in a LN167 (IFS) what will I need in the front ?
I haven’t had much to do with torsion bar ifs front ends sorry man
Hi There is there anywhere online you can buy the long slip drive shafts from?
I wish this video was in english
Hey mate love watching you and I'm gonna build my own tray for my ln106 and love your design and I was gonna try and match yours but a little bit longer and wanted to know the measurements of the rear part from the side to first angle cut on each side
I need this stock sir I like this cars can you send me details and contact information
What did you paint the tray in what products for the undercoat and final coat ?
Just used White knight rust guard epoxy enamel in satin black. Majority I didn’t prime
@@HaydnKamp oh yeah looks sick luv the build, thanks 👍
Saw the other ln on market place
Yeah ended up having to sell it unfortunately man
Hey mate Question for you Would these rear leaf springs fit a duel cab ?
Yeah sure would Micko
Another question man I’ve already got 2inch straight shackles in the front would they work or do I definitely need the banana shackles?
How do I know where to weld the mounts and what do I do to make mounts to fit onto the chassis. Can you show that
Have a look at the full length video man, should have the answers your looking for
Hey mate, what other front shocks would you recommend if i wanted to safely do beach runs and highway driving with this setup?
Superiour do a range for the hilux that are decent for the money. Open - Closed / Lift / Travel mm/inch 605 -370mm / 5inch / 235/9.2 565 - 350mm / 4inch /215/8.4 535- 335mm / 3inch / 200/7.8
Patrol
Patrol drivers would have too much foot twitch to drive up the wall. Or they’d hit it in 2nd head on trying to ‘bump’ it🤣🤣
A DashMat is essential for protection from Sun Cracked Plastic...Are you a Clown?
In the USA. Love the lights! I’m trying to get ideas for a flat bed build and this is probably my favorite ones so far. Where did you find the lights?
A company called LED auto lights make them. Maxilamp series
Thank you. Awesome build. Looks so good.
What a bunch of rigs!!
Peak hilux goals 😅
Great work mate! I’ve been putting off finishing my 89 IFS 4Runner in the hope of going full three link/ coilovers with SAS but this has me thinking differently 😊
Cheers mate! Leaf springs do impressive things when set right 🤘🏻
@@HaydnKamp thoughts on ladder bar to reduce long leaf axle wrap in the back?
Would definitely help, I haven’t bothered as it doesn’t seem to be an issue with 80hp 🤣
Hi Hayden, when's your next video coming out?
Unsure man, I’ve had to sell the RN so this little series is no more unfortunately
@@HaydnKamp that's a bummer.
🫠👍👍👌🤙
😈😈😈
A top build. Got a LN 167 double cab. Really inspired me to build one.
Cheers man! Get after it, great project building a tray 🤘🏻
Like the cheap simple mods using a bag of mixed oem parts. That’s the roots of hot rodding too.
If it works it works hey!
just wondering mate how much did all of this set you back $
Roughly around $1,000 Joel
would u ever consider building another one of these
I tried recently but ran out of money and had to sell it 🤣
Bloody awesome mate! Can i ask what welding machine you are using?
Unimig viper 250, about 7 year old
Great video mate You done well .. I’ve got a old LN scrubbing 305x75 16 s on the front guards 🙄 So il be looking at doing this for sure 👍
Thanks mate! This will sort that issue out for ya 🤘🏻
I have ordered one. While driving to the foggy mountains on cold and raining it was good and happy with it. Upon my return home the next day I found there is a condensation building up from end to end. I look at KZread how to remove the water vapour. Remove the valve. On the light for 30min close the valve and off the light. But it doesn't work. I take picture and email to Auxbeam asking how to prevent or remove the water vapour. Their reply was they seeking advice to their technical but till today no news. This is the first and last for me with Auxbeam.
After posting this. In the evening I received their email and they are sending a new light bar same model as replacement. If this is the case they held responsibility and guarantee to replace I will continue to use Auxbeam. Thank you Auxbeam
What a great video! Keep it up. Ive been wanting to do this to my ute for a while now. Just wondering how long do the breaklines has to be and what degree caster wedges would you recommend? 💪💪
heavy duty
It’s still holding up great 🤘🏻
@@HaydnKamp The lines, especially the rear end with the lights look sex