Пікірлер

• 
  @pyreotusbark89547 сағат бұрын

  Does this work with the old economizer actuator

• 
  @HVACKnowItAll5 сағат бұрын

  No, you'll need a new one

• 
  @pyreotusbark895444 минут бұрын

  @@HVACKnowItAll Thanks for the answer. The customer decided against repairing their economizer because they didn't want to replace the actuator and the control module so they'll just be running the mechanical cooling now instead. For future reference, do you know the part number of the actuator that replaces the one you're replacing in this video? It looks very similar to the one in the machine I was working on today.

• 
  @ilovenythismuchilovenewyor58019 сағат бұрын

  wont air get in the lines tho??

• 
  @HVACKnowItAll7 сағат бұрын

  The compressor is isolated from the lines and under a vaccum

• 
  @ilovenythismuchilovenewyor58017 сағат бұрын

  yea but introducing the oil from open top oil can u would think oxygen will b introduced

• 
  @Darton-ok5xt10 сағат бұрын

  pls help, how do i know which ac hard start kit for my residential ac lennox 5 ton

• 
  @HVACKnowItAll5 сағат бұрын

  Look up the selection that Supco has and their specs

• 
  @gilbertomejiajr1706Күн бұрын

  I'm here because I saw you write this on ig 😂

• 
  @HVACKnowItAllКүн бұрын

  Lol

• 
  @davidcarpenter92342 күн бұрын

  You forgot to put the flare nut on first, ROOKIE!

• 
  @HVACKnowItAll23 сағат бұрын

  😆

• 
  @NobodyJones2 күн бұрын

  The unastrut sticking through the middle of the van is very relatable

• 
  @HVACKnowItAll5 күн бұрын

  Man, I'm watching this 5 years later and cringing at my video skills back then 😂

• 
  @hectortorres5425 күн бұрын

  Finally found a mechani. Can't explaining the valve function. Function just one. Thank you when you start from city one turn. The term is cracked to the port. Thank you for the video

• 
  @zekenzy64865 күн бұрын

  Great video. Thank you for sharing

• 
  @shanegreen2686 күн бұрын

  Awesome thanks for sharing your knowledge

• 
  @HVACKnowItAll6 күн бұрын

  My pleasure

• 
  @thesilentonevictor6 күн бұрын

  Excellent troubleshooting tech

• 
  @HVACKnowItAll6 күн бұрын

  Thank you sir!

• 
  @ayoutubewatcher70096 күн бұрын

  lol this is basic hvac 101

• 
  @HVACKnowItAll6 күн бұрын

  "lol this is basic hvac 101" no kidding bud, what's next?

• 
  @stephwaylonwells32187 күн бұрын

  👍

• 
  @HVACKnowItAll6 күн бұрын

  👍

• 
  @eastcoast1867 күн бұрын

  Thanks for the video

• 
  @HVACKnowItAll7 күн бұрын

  My pleasure

• 
  @LilyRoseElectric7 күн бұрын

  Great job 🎉

• 
  @HVACKnowItAll7 күн бұрын

  Thank you!

• 
  @fathmasameer75237 күн бұрын

  This man is amazing always great

• 
  @HVACKnowItAll7 күн бұрын

  Cheers!

• 
  @mtgwdefender7 күн бұрын

  Excellent video. Clear, simple, & Straight to the point. THANK YOU!

• 
  @HVACKnowItAll7 күн бұрын

  You're welcome.

• 
  @bobrub7 күн бұрын

  Turn your phone HORIZONTAL .... Vertical videos SUCK .... that's why I don't watch SHORTS at all!

• 
  @HVACKnowItAll7 күн бұрын

  I use my content for multiple platforms. They are all vertical unfortunately

• 
  @kodfish1017 күн бұрын

  ​@@HVACKnowItAllkeep ts vertical dawg 😂 the people here taking in information you are giving out for free don't care. Thank you for posting this in general

• 
  @HVACKnowItAll7 күн бұрын

  HVAC methodical troubleshooting

• 
  @kirubakaran36957 күн бұрын

  Very useful information, I was searching for it.

• 
  @joelalleman95918 күн бұрын

  on my vacuum pump , it has what is labeled as a blanking valve . is this what is considered the gas ballast valve ??

• 
  @HVACKnowItAll7 күн бұрын

  No

• 
  @hisinvisibleness-fn8qj8 күн бұрын

  Come on man dont wax philosophical about a squirrel cage Im busy😂

• 
  @bryananderson37878 күн бұрын

  What would the result/symptoms be if the solenoid were to get stuck in the open(unloading) position? Would pressures equalize?

• 
  @jaybusa769012 күн бұрын

  Make this is EXCELLENT EXPLANATION!!! Wgreat video

• 
  @dubking-dm4wu14 күн бұрын

  can i use this for lifting things on roofs just extend the rope

• 
  @HVACKnowItAll12 күн бұрын

  Not really no

• 
  @liudxdx16 күн бұрын

  Man you are a hero. I have watched over 20 videos on how heat pump works, I was so confused, like fucking water actually mix with refrigerant? Like wtf, nobody mentioned or explained the coaxial coil and how it works. Thanks god I found your video

• 
  @HVACKnowItAll15 күн бұрын

  Glad to help sir

• 
  @marvinmurray552017 күн бұрын

  Thanks bro!

• 
  @hvguy18 күн бұрын

  Just what I needed! I was wondering why no freon was going in.... Turns out I have no idea what I'm doing. But now I kinda do!

• 
  @Dicktoben19 күн бұрын

  I stared my hvac business in Canada 12 years ago. I’ve always just wanted a balanced work life. I knew very little about business and hard to learn thru a lot of bumps. I was tired of working for somebody, counting on the weather to keep us busy. It’s so hard to get ahead in business, especially with the crazy economy. Here it’s hard to sell a 3 ton a/c system for 5000$. I see guys in the states that wouldn’t touch it for less than 10-15k. Business stresses me out. I’m tired of the rollercoaster and catch up game that always seems to be going on. Sometimes I wish I never got into this. There is a few perks for sure , but sometimes I just wish I stayed working for the man

• 
  @louievil71320 күн бұрын

  Nice thank you I'm getting 15.7 across all three leg start run and common. It was a little hot but all three legs are Reading the same so it is not grounded or in thermal lockout. But when the 24 volts are engaged the compressor stays at 290 on the low side and high side it is not adjusting in any way.

• 
  @Mudo9421 күн бұрын

  Any review on the pocket version I think it’s the pocket 2

• 
  @mclmm677324 күн бұрын

  Usually one of the worst issues these units have that is always not addressed at the factory is bad soft foot from those formed bases. I routinely see 0.020-0.050” soft foot.

• 
  @boywhohadatiger25 күн бұрын

  Found one like that on a carrier today tripping the breaker

• 
  @BernWag25 күн бұрын

  can you cut steel with that rig? Also, when brazing, do you have the option of using just MAPP or do you have to use O2 all the time?

• 
  @l.crossjr25 күн бұрын

  Geat video. I know you did not flow nitro for demonstration purposes, what is the best way to remove those flakes from that txv afterwards?

• 
  @HVACKnowItAll7 күн бұрын

  Using a flush system like RX11 flush but nitrogen will avoid all that. In reality RX11 is only for linsets

• 
  @JorgeMontes-ji2sd26 күн бұрын

  Boring mtfkr

• 
  @jgarcia806726 күн бұрын

  How much was the set, an estimate since it was last year. And how much is each tank? 🤔✌🏾 I’ll plan ahead, thanks in advance.

• 
  @Ray-gf4vf28 күн бұрын

  the whole static pressure is a shit fools gimic to make more money

• 
  @HVACKnowItAll28 күн бұрын

  Lol, that's hilarious bud!

• 
  @ja255329 күн бұрын

  Golf clubs? Lame.

• 
  @HVACKnowItAll29 күн бұрын

  The fact you took tike to leave a negative comment is lame lol. Here's a hug pal.

• 
  @Ray-wr2wr29 күн бұрын

  Is it Boost spp6 would be efficient for 45+5 mdf capacitor? Thanks!

• 
  @sarahgibon5610Ай бұрын

  .

• 
  @odl1307Ай бұрын

  Hey is it possible to use the super evac manifold on a Mitsubishi heat pump for example the MXZ models when pulling vacuum, on the port inside the heat pump? Basically I was wondering if it’s possible to connect 2 hoses there to pull a vacuum faster. @hvacknowitall

• 
  @ShahidKhan-ws8rcАй бұрын

  You have comprehensively covered the whole topic in such a short description n video. It's an incredible brief technical guide

• 
  @chrissipple1018Ай бұрын

  Always ask if the nitrogen cylinder has been used for clean nitrogen only. Sometimes the cylinder was used for some other gas and it just gets repainted. If it has had some other gas in it you now have dirty nitrogen and you can get high levels of copper oxide inside even though it's clean gas. If possible get only medical grade nitrogen, the sales person will probably give you a strange look but tell them that is what you want. And even with clean and pure nitrogen you will get some copper oxide build up.

• 
  @HVACKnowItAll7 күн бұрын

  Counter guy will zero idea about this

• 
  @angrynas9668Ай бұрын

  Cheking superheat near desire temperature

• 
  @l.crossjrАй бұрын

  Very good

• 
  @USA-GreedyMenOfNoIntegrityАй бұрын

  Heat the joint first. If your gap is snug, heat will transfer quickly to pipe. If not snug, use a lever type swaging tool.

• 
  @josecruz3237Ай бұрын

  The 40 F minus 75 F in my opinion . The 40 F . is just the temperature at what the refrigerant begins to boil with out gaining any heat just as soon passed through the metering device. The more standard temperature measurements is Delta T . Temperature of the air coming in the evaporator and temperature coming out of the evaporator. The other temperature that is importance is S.H that is the gain of heat in the refrigerant after it saturated or is changing state from liquid to vapor. But this is a different way to see the temperature difference Thanks

• 
  @HVACKnowItAllАй бұрын

  TD is used in coil design and is very important.

• 
  @steveashcraft718Ай бұрын

  My Heil furnace is eating blower wheels. It's getting it's second wheel this week. They're only lasting maybe 4 years.

• 
  @HVACKnowItAllАй бұрын

  Buy a better, more expensive wheel! Or have your airflow and staic pressure checked.

• 
  @steveashcraft718Ай бұрын

  @@HVACKnowItAll , My HVAC man is using OEM wheels. I'm not the only one having this problem.

• 
  @espinozajc64Ай бұрын

  Excellent 😊