That was a Masterclass in Soldering!

hi sir this modification for what

Nice work man iv just plugged in my turbolamik and i have a short to ground fault on speed sensor 2 do you think i possibly messed up with the soldering or mashed the sensor putting it back together

@ryutech_automotive

11 ай бұрын

Check continuity between speed sensor 2 and TCM body. See if the solder connects them

@rayjones3473

11 ай бұрын

@ryutech_automotive I have now sorted it it turns out it was a faulty pin on the tcu itself changed the pi and I'm cooking 🍳

Hi! Great job! Is it works with standard bmw software? Can I use this instead of programming the transmission immo?

@ryutech_automotive

6 ай бұрын

Hi Max, this PCB is not to replace the stock TCM. This is to bypass the valves inside for the use of aftermarket controller, hence can't be used with standard installations.

@Amaxauto

6 ай бұрын

@@ryutech_automotive Thank you! I understand now.

Question: Did you replace the 4 plastic rivets when finished?

@ryutech_automotive

2 жыл бұрын

We put a dash of epoxy covering the used to be rivets, but it is not necessary because the plastic cover has a lot of latching locks.

@adalbertbusch70

Жыл бұрын

Qweston ZF6HP26 09E

@ryutech_automotive is there a difference in PCB between an HTG and a Turbo Lamik? The reasoning behind the question... Let's say, I'm using an HTG TCU, then decided to switch to Lamik. Will there be a difference between the circuit boards?

@turbowankel1264

10 ай бұрын

All the boards seem cross compatible

@RS-lt2ue

10 ай бұрын

@turbowankel1264 thanks!

Do you like turbo lamik or HTG controller better? And why?

@BEYTEK

2 жыл бұрын

Lamik imo

@piovo5222

2 жыл бұрын

@@BEYTEK why bro?

@maderpl1

Жыл бұрын

only HTG. Closed loop works perfectly. You can launch, do transbrake. Also HTG does frequent updates.

Do you get any codes from doing this?

@ryutech_automotive

2 жыл бұрын

It is for a standalone controller so it will not be compatible with oem functions

Maybe you don't know ZF6HP26 Audi pinout wiring?

Can this be done for Benz 722.9 the control strategy seems simple enough

@ryutech_automotive

2 жыл бұрын

Contact HTG Tuning for the control, they might have plans to add it in the future

Can you do this for a 6hp?

@ryutech_automotive

2 жыл бұрын

Possibly yes if there are demands for it

@jdmtechllc6589

10 ай бұрын

Demand

Hii

피시비 판매 하시나요

@ryutech_automotive

2 жыл бұрын

당신은에서 구입할 수 있습니다 : www.ryutech.co.th/product-page/8hp-pcb-for-htg

Ooh this was painful to watch for many reasons. I've got one of these gearboxes. No idea what this modification is for, but I can solder, I'm an engineer, Painful. Use a toothbrush to leave any metal filings on top of the old circuit board? Mental.

@ryutech_automotive

2 жыл бұрын

The fact that you have no idea what this is for; an 'engineer' would think about searching google for 'why' and try to understand complexity of modification rather than thinking 'painful' :)

@jdmtechllc6589

2 жыл бұрын

@@ryutech_automotive Brutal bro, he could be a bridge engineer right? Also his comment seems spur of the moment, and he just didn’t care enough to research. But I do see your point as well.

@ryutech_automotive

2 жыл бұрын

@@jdmtechllc6589 The solder methods in the video might not be the best, nor using the best of equipment, the purpose of this is that installers (garage) can follow through with off the shelf tools. He does have a point for using toothbrush, but if you ever do the modification you'll know that it is quite frustrating to clean thoroughly.

@jdmtechllc6589

2 жыл бұрын

@@ryutech_automotive totally understand, and I know there’s a lot of white knights on the internet who never turned a wrench.

Can you please send me 8hp70 pcb

@ryutech_automotive

Жыл бұрын

you can order them here: www.ryutech.co.th/product-page/8hp-pcb-for-htg