Listen, there's nothing you can do to stop me from using the Chain Machine to press in BB30 bearings

@BikeNewLondon

Жыл бұрын

You're gonna get a little home visit from "Customer Service". :)

@kwizmon

Жыл бұрын

I say go for it.

@Mauricio-oq1tm

Жыл бұрын

GO boy, go!!! That's your shit! It's your money!

@ethanbowering9944

Жыл бұрын

Chain machine?

@cebruthius

Жыл бұрын

@@ethanbowering9944 Cyclone chain cleaner I guess?

When mentoring junior bike mechanics in the shop, my first (jokey but firm) warning is that anyone found using the 15mm cone wrench on axle nuts will be immediately fired. 😉 Next is to get in the habit of spinning nuts and bolts the 'wrong' way when threading them on, until you feel the ''click of the start of the thread - it greatly reduces the chances of accidental cross-threading, especially in soft metals. Also, get used to to feeling the tool's feedback through your hand - especially important with chain-riveters - once you've felt how it feels when it goes well a few times, use that 'finger-feel' knowledge to immediately back off and re-seat the tool if you feel the pressure going past what you'd expect - saves a lot of bent tool-pins and damaged chain-links.

@dudeonbike800

5 ай бұрын

Ha, ha, love it! I wrote using a cone wrench on a 15mm nut above before reading your post. Genius minds think alike!!!

The key to tool use is to engage one's brain before engaging the tool. Think about not just what you wish to accomplish with the tool, but also what could go wrong. For example, go through the motions of loosening a very tight nut or bolt without the tool, and see where your hands will wind up if the tool slips. I've avoided many knuckle injuries, and saved damage to parts and tools, by applying this process.

@ygoeb13

Жыл бұрын

this is basically exactly the thought process of orthopedic surgery too

@kevinruiter8715

Жыл бұрын

Lefty loosy righty tighty

@rangersmith4652

Жыл бұрын

@@kevinruiter8715 With bikes, not always. In fact, every bike has at least one thing that's lefty tighty.

@RickyHolton

Жыл бұрын

What’s the park tool part number for a brain? I’m not sure I have that tool…

@Yoda-em5mt

Жыл бұрын

@@rangersmith4652 two things if you have a threaded bb . Forwards to tighten backwards to loosen with bike up the right way .

Top tip, assess where your bodily extremities may end up if the tool slips. Particularly important when working around anything pointy like a cassette or chainring. Scrubbing drivetrain grime out deep cuts is never fun. Top Tip #2: It's not always lefty-loosy. I learnt this expensively the first time I tried to remove a BB cup from a frame. Destroyed the cup, bent a breaker bar, and almost trashed the BB itself. On the subject of applying leverage I wonder if you also agree that certain jobs (removing BBs, cranks, and pedals) is best done on the ground, particularly if you don't have a pro-level workstand.

@LasseGreiner

Жыл бұрын

Yes, the ground is your friend for applying pressure!

Man, I’ve seen Calvin okay it so straight for so long. I had no idea he was so funny.

Calvin you are simply the best. I review parktool videos and I always look at your first. Never been disappointed.

That last tip, “bring the tool levers together”, is excellent. I’m guilty of making that mistake myself. Why struggle? Seems like common sense, but I never really thought about it before. Thanks Calvin!

@maxrainwater

11 ай бұрын

Use the mechanical advantage, Luke!

As a retired auto tech/instructor I couldn't even start to list all the misuse of tools or the use of the wrong tool. good video.

@jamble7k

Жыл бұрын

a hammer fixes everything

@jm19592011

Жыл бұрын

@@jamble7k At least once :-0

Took use timing: the last time you want to use a tool is immediately after you have messed something up a little bit…great chance of messing a lot! Instead, go for the coffee-drinking tool and sit on the butt-supporting tool until you have stopped swearing and are calm enough to use the skill inflation / thinking tool again. Seriously though, the most recent mistakes I have made have all happened when I was too impatient to go get my reading glasses (which I only ever needed after turning 50), and tried to do something without actually being able to see!

Can we have a video on the proper use of Vice-grips for polished aluminum parts?

All the best for the new year Clavin. Best mtb service/repair content on the Internet!!! Thanks for the service 🙏

Check your surroundings when you're going to crack a nut or screw too. Consider where your arm is going to go. You don't want your arm to move past or into anything sharp after you crack the fastener. This is especially true if you're working on machinery with cutting tools in it, not just chain sprockets.

@flashwashington2735

Жыл бұрын

Or around the sensitive ears of wife and kids! @##№$h¡7 😉😆😆😆

Great job , Prerequisite for Anyone starting a repair !should have had this when I started repairing my bikes as a kid. Park Tool saving components tools and mechanics .

i love watching these videos. They have helped me to fix my own bike in a pinch and helped me learn to to help to become a bicycle mechanic and my own study on the subject. keep up the great work

Thank you Calvin and Park Tool for the advice and the many great tools over the years. We run a community bike shop. Our tools get used by people of all skill levels. Park Tools work best and hold up the best. A few we have found out the hard way that care is rewarded, and the lack of care ends up in broken tools or worse. Chain tool tips are a good example of this. All in all, Park makes the best and most appropriate tools for the job. I do have one complaint, perhaps an objection to the idea that we're using the tools wrong. We work on a lot of tired old bikes, either repairing or parting out. So of course, removing cheap MTB freewheels is a regular thing. We have broken numerous FR1.3 tools in doing this. They just crush and split, either in the vise or adjustable wrench. Inside a 1 inch box wrench they survive a little longer. But the packaging and the video for the tool show using a large adjustable to spin off a freewheel. The 1.3 is not strong enough. What works to do this? My trusty 20 year old FR1.1, or a small socket wedged inside the 1.3 for support. I don't want to return any more of these. I wish the tool was stronger! Thanks for the tools, support, and videos!

@flawless7019

Жыл бұрын

While park tool is truely great, companies like Wera make outstanding quality tools.

@zharifwahab1793

Жыл бұрын

@@flawless7019 Wera doesn’t sell freewheel socket.

@DennisWurster

Жыл бұрын

One technique I've seen is to mount the tool in a bench-vise and then set the wheel on top of it. Then you can use the wheel itself as your lever to loosen the freewheel.

@BikeNewLondon

Жыл бұрын

@@DennisWurster Thanks, Dennis, yes we use this technique as well. Without something to reinforce the center of the FR1.3 it can crack and fail in the vise too. I think we're up to 4 or 5 that we've had fail in the shop in 3 years. We also have now a 1 inch socket modified with flats on the outside, so it can be clamped in the vise and hold the tool without slipping. Seems to work, with a few spacer washers inside it for correct engagement height.

I've got one!! Hex keys and soft steel bolts. AVOID BALL END HEX KEYS on high-torque applications. Example would be crank arms and derailleur cable bolts. Ball end hex keys can twist in the fitting and lodge in, possibly marring the threads or allowing bad engagement with the bolt. USE NORMAL, FLAT HEX KEY sockets for proper tool engagement and to get the proper torque spec. on your proper components. Also; when driving on large bolts e.g. cranks or pedals, use a large driver. It's difficult and unsafe to try to load 30-40nm with an allen key - step up to hex key sockets with a 3/8" ratchet driver for much safer and more effective tool use and result.

You can use the smaller (square taper) crank extractor to remove octalink and isis cranks, you just need to put something in there to cover the hole in the spindle, there are adapters for this specific purpose. Some crank extractors also have interchangeable feet to match the cranks being extracted. Phillips screwdrivers will eventually round out derailleur adjustment bolts/screws so instead of buying a JIS screwdriver (the proper tool for this), I find that it is easier and cheaper to just replace the OEM bolts with hex socket head bolts and use allen keys

@martinkrautter8325

7 ай бұрын

easiest makeshift type of adapter for isis cranks is an adequately sized counterhead screw. been there, done that.

It's always nice, too to know which way to turn the tool. There are always exceptions to Righty tighty, lefty loosey. I spent many a wasted minute turning the wrench the wrong way.

Explained very well and found useful. Thanks Calvin.

Great advice Kalvin Thanks.

Happy New Year, your tips on how to service bikes come in handy and I recommend your tools to everyone

I'm dying 😂 This is the best tool video I've seen from anyone in a while.

You're the man Calvin Thank you so much for your videos.

Calvin really rules!!

Proper positioning of a crow’s foot on a torque wrench. Gotta be 90° to the shaft, if placed straight out off the end, the torque setting will be off.

You actually got me on one. I bought an old bike to refurbish for my son. The BB was square taper. Without even thinking, I just grabbed the tool I normally use on my bikes. It managed to remove it. It forced the wider foot through the smaller hole. I just thought it was being difficult because it was an old bike hasn't been used in long time and it was stuck. When the crank came off, my tool is now stuck in the crank. LOL! I quickly realized the error of my ways. Fortunately, I wasn't reusing the crankset anyway.

Using cone wrenches for anything else. Once saw a one-star review for a cone wrench online from someone who'd destroyed it while using it for a pedal or something - but complained about it being just stamped metal. The vendor replied, very carefully and politely saying, basically, 'you idiot.'

Great tips, thanks!

Incorrect tool use: using just about any tool as a hammer. On my job site in the bush we often have limited tools available and "can you pass me the adjustable hammer" has become a common request. 🤣

My favourite was not having the correct hex bit, so I'll try that star shaped one, whatever the hell that is. Well done me. Well done.... Moron!

I always install and remove pedals (and crankarms) with the wheels on and the bike on the ground. That way I can position the tool to allow me to push down towards the ground, using my body weight to apply force and the drivetrain and tires to hold the crank arm in position.

Calvin, thank you for making this video. I’ve rounded out a few bolts in my time but I didn’t realize there were so many ways to use tools wrong! My worst offense is using a. TW-5.2 torque wrench at bad angles because of a tight angle. Is there a better tool to use for tight spots?

Would be worth mentioning considering the handle path of the pedal spanner when it suddenly comes loose - i.e. making sure you don't send your fingers straight into a chainring.

@weast2123

Жыл бұрын

absolutely. it was kind of unintentional, but the name "teeth" is certainly fitting.

Bonne résolutions 2023 😊 Thank you Calvin .

Every tool is a hammer

Man you guys sure have a lot of funky lookin' hammers.

I learned early on in my tinkering to pay the extra and buy a Park Tool tool for the job. Never had a tool fail and they always work.

@DrewskiTheLegend

Жыл бұрын

I’m still selective. For anything high tolerance I will buy park. I don’t need the mallet or the dang grease gun. Great tools, just pricey for what you get sometimes.

4:10 For safety, I put the rim in a vise and prevent it from turning with a piece of wood through the spokes. Air tools help a lot too.

i grew up BMXing. and installing a-headset cups and those press-fit bottom brackets with a hammer and a piece of a 6x6 post was normal in the 90's

I need to see if any of my Park Tools talk in Calvin's voice next time I am in the garage!

nice job guys

When I first got my chain whip, I accidentally turned my sprocket the wrong way, overtightening it. I eventually had to sheepishly take it to my local shop for them to get it loose again.

Not holding the bearing cup when using the extractor. Sending the cup flying across the shop 🤣

7 seconds into the video and I had to hit the like button.

Been using the park tool crown race setter for ec34 cane creek crown races and they’ve never been a good match but it took me years to decide to order the right fitting from cane creek.

When I was head mechanic at one shop that was shared with an outdoor shop, the outdoor people often used my JIS screwdrivers to make product displays. So one day, I bought a decent quality screwdriver for every one of them. When I handed them their screwdriver, I told them that if they came for my screwdriver again, we were going to fight. My beautiful screwdriver would last THEM one use before they damaged it. It would last me many years.

Using a knife as a tyre lever, using a rotor alignment tool to straighten a bent rim, using needle nose pliers to unscrew a perfectly good stem bolt, removing the self extracting bolt from self extracting cranks and wondering how to remove them, 3D printing a dust cover to stop a BB from unscrewing, someone else taking rubber rim tape and peeling it apart when you look away, when the left pedals doesn't screw in the right crank, use the wrench harder. Some fun.

That thumbnail is amazing

Calvin or the awesome Park Tool team… what do you say to a little trip to Fiji to help a super bloke and his 2 sons get set up with a much needed bicycle repair shop (they don’t have one there). Boy would that make a good video and be a great trip out for you guys plus being the main sponsor for the growing cycling community in Fiji of course 😉

I broke the plastic needle "Proboscis Tube" of the Park Tool TSI-1 sealant syringe months ago. I see that it's $1.83. I'll get around to buying it some time.

¡Feliz año nuevo don Calvin!

Funny this vid should pop up as I just bought a Park Professional truing stand and disc brake alignment jig. For years built wheel in the bike frame. Love the spoke wrenches. A cheater pipe can be a knuckle saver by the way.

excelente 👌

Comedic talent and a great instructor.

Sales guy vs web dude!! Classic!!

I have a number of Park tools in my MTB kit. Very good tools that have served me well. Could be I did have my brain engaged, grin.

Calvin are the only one true repair master! 🙃

As a lifelong bike mechanic I have seen many instances of people using their tools incorrectly, or using the wrong tools for the job. The thing that steams me the most is rounded nipples as I assume some of the damage was done by some teen working in some bike shop who could not be bothered to find the correct spoke wrench! Most bike buyers do not try to true their own wheels. Also, I often see deep scratches and divots on rims from screwdrivers used as tire pry bars! I use either the Park TL-5 levers or heavy duty plastic ones. Never screwdrivers! Sure way to pinch a tube! Last, I use only good quality stainless cables and the correct housings. When I see brake housing on shift lines I want to hurl! Not the biggest sin perhaps but easily avoidable by not buying those prepackaged cables/housing with a brake end on one side and shift on the other! I have not used these things after age 12! When I knew no better! Last, when I see rusted chains I want to scream! It is not difficult to service a chain! And stop leaving your bikes in the rain!

I use my Park Tools CM-5.3 chain cleaner to clean my neckties and suspenders. Win!

Thanks so much for this guys. As a You Tube certified mechanic, my education never included all the theory parts like this :) This is super helpful stuff. Also, gee I'm starting to dislike lock rings on disc rotors for this reason. Have a couple I want to take off, and getting decent purchase on a through axle wheel can be really tricky.

@zygmuntthecacaokakistocrat6589

Жыл бұрын

'YOuTUbe CeRtified MecHanIc' lol

@AlanHead

Жыл бұрын

Just wait till you encounter a T47 BB. Similar width of engagement to a rotor lockring but torque spec is 50Nm. Naturally Park have a new tool to help

Nice, need many tools

Funny stuff. BTW, love my PP 1.2 brake tool. The metal handle is sort of funny, but the black rubberized portion is perfect for tapping my XT lever and caliper for bleeding and the hard blue plastic end is great for tapping them to work the bubbles up! Keep up the great work! 🎉😂

I'd go back to square taper BB in a heartbeat if I could. I don't like Hollowtech 2. Octalink wasn't bad. I run a M970 crank that (as far as I know) is the only one that exists in the form factor it does - it's got a 24mm Hollowtech 2 size spindle and thus it works with all Hollowtech 2 bottom brackets, but it has a far more chunky mating surface, quite like an Octalink. Also, this crankset doesn't have the typical (and stupid) 2 bolt system found on HT2 cranks (where the bolts strip, ruining the left crank arm) for tightening, it has just one huge bolt that gets tightened to 40Nm on the left crank. I love it. You might wonder why I use it, if I "would go back to square taper in a heartbeat" - well because my bike has a stupid press fit BB shell and thus, I have got a Praxis Works converter on it (PF30 to HT2) and that's why I have to run a HT2 spindle... Praxis Works just don't make a converter from PF30 to square taper and even if they did, I don't think it would be sensible in a press fit shell. The old M970 crank is the best design I have seen, whereas the most recent HT2 cranks have a weak mating surface and the M5 bolts that say 12Nm on them often strip. I mean isn't it obvious why? M5 bolts (or maybe they are M6) and 12Nm don't go together well! The max I'd say a M6 bolt should be taking is up to 8Nm. Design flaw. Why not use the M980 crank since it's newer? The chainrings are a proprietary BCD, whereas the M970 is standard 64/104 BCD. There isn't a better triple crankset for MTB other than the M970.

Hey calvin! I attended the two-week course at Barnett bicycle inst Colorado springs. October 1992. Damn you are good instructor. I've been a mechanic and a shop manager on and off. Sadly I no longer have my sutherlands or Barnett bicycle mechanics book. Happy that you are doing well.

Why can‘t all tool manufacturers‘ videos be like this? Excellent video!

Thanks Calvin nice tips video see you later

Love your videos! I guess the most miss used tool I've seen is tire removers! They should provide a nice easy glide when inserted correctly, but most peopel.tend to struggle to move them.

Use the right torque and/or make sure to never over tighten anything. I've seen so many people over the years (especially the general public) think a screw or a bolt needs to be as tight as possible. Either use specific torque wrench, use the right torque setting on your screwdriver, or manually quarter turn backwards

I abused my square tape bottom bracket tool on a stuck cartridge bottom bracket rounding off the splines a bit. So now I need to add a bolt into the pedal threads to hold the tool in place so it doesn't slip out. Also I now use impact guns to loosen cartridge bottom brackets (which is not very often anymore).

I was once accused of misusing Park pedal taps (tap-3) to clean up the threads on a one-piece crank. The description says they are for use on alloy and steel cranks, but the shop manager wouldn't hear it.

Last tip in the video, avoid pushing with one arm and pulling with the other when opening a tight thread, very easy to hurt your back.

hello!! very good video! they are always very helpful. A tip to improve would be to increase the lighting of the recording set. greetings from Argentina. Jorge

I often use wheel QRs, a bolt or all-thread, washers and nuts to secure bb tools, rotor lock ring tools and others to hold the remover secure. Then it's impossible to slip off under incredibly high torque. This is great trick for over torqued and corroded components. Then you can turn the remover with an open or box wrench. I'm NOT a fan of the newer Park aluminum bb tools with no wrench flats. They're also thin walled and appear flimsy. I'll only buy them if I have no other choice. To be honest, I haven't broken one yet, but they don't instill confidence and I can't turn them with an open end wrench. I generally like Park's STEEL TOOLS and use them every day. Park, PLEASE make ALL STEEL tools that are designed to be used in high torque applications with breaker bars. Competent and or pro mechanics are willing to invest and pay extra for quality long lasting STEEL tools. Quality,long lasting tools are made out of steel. Steel is real. I'm a retired machinist/inspector/4wd nut become bike mechanic.

This was all solid! One addition would be that Philips head screws are as good as aluminium chains...

This is why I got the Shimano TL-MH10 curved breaker bar so you easily will get the forced applied as close as possible to the engagement point.

I think the worst is using cone wrench for pedal removing... ugh the worst I do is using anything large enough as a hamer

If you have a square spindle on your bottom bracket and find it hard to take off try this. Get an empty milk bottle, put a piece of string through the hole at the end of the tool and then thread it through the milk bottle handle. Fill the milk bottle, the weight will pull the tool down, if need be use two milk bottles.

Glad I'm not the only one spinning the THH-1 like a helicopter

@mattgies

Жыл бұрын

I even added a drop of lube so it spins better.

Tool tip: If you're trying to undo a stuck screw, ideally before you round it off, but even afterward: Use the principle of tool engagement (apply downward force to prevent the wrench slipping), even tap it a bit with a hammer to get full engagement. Then, use the grippiest pair of pliers or vice grips you have to grab the head of the screw and turn both the wrench and the pliers in unison. This has given me just enough grip to remove many a stuck bolt that wouldn't budge with either method alone.

Park Tool the best tools.

Anything can be a hammer

I used a quick release skewer to hammer out the crank tool foot. I just slid the quick release skewer in from the opposite side. It was easy.

Wear appropriate gloves for the job. When unscrew locking rings for disc rotors for example, like Calvin did. Nice to see how easy you can slip and end up cutting your hand on the sharp rotor edges. I learned that the hard way. Nice heavy leather glove for the hand holding the tool on the rotor from that point onwards. Also prevents injury when sending your hand in a chainring when unscrew crank arms.

I'm new to mountain biking, but I swear I've seen video's with this guy labeled at least 7 years ago, and he looks exactly the same.

I, no wait, a person i know uses the small foot crank arm puller on octalink bb by putting a drift punch inside the bb which pushes against the bolt on the other side.

Use of a crescent wrench to tighten spokes. Spoke wrench, better choice.

My biggest problem is not allocating enough time to do the work

Regarding the pedal tool and levers, I like to have the wrench only a few degrees off the pedal arm and squeeze the two together to torque the pedal down. Then you don't have to grasp the opposing crank arm at all

The thumbnail lmao 🤣

Hold your torque wrench from the middle of the handle!!!

Use a wheel quick release and washers if need be to hold the tools in place.

@BikeNewLondon

Жыл бұрын

I bought a longer bolt (M12 fine thread) at the hardware store, and washers for spacers, to keep bottom bracket tools like the BB30 engaged while getting cups loose. Engage into the bolt hole in the end of the square taper spindle, break loose the cup, then back off the bolt as needed as the cup unscrews so nothing binds up.

@brandonreimer184

Жыл бұрын

I have used a bar clamp to do the same with square taper bbs.

I'd like a talking pet chainwhip alligator to encourage me to use tools properly. Will Park Tool sell me one?

JIS cross-slot derailleur limit screws don't play well with US Phillips screwdrivers (it's not you; it's a different standard). If you don't have the JIS screwdriver, the screws are generally also slotted for a small straight blade. Try it; the gods will be pleased.

@parktool

Жыл бұрын

Yes we do, see www.parktool.com/en-us/product/derailleur-screwdriver-dsd-2

@ajwitt7472

Жыл бұрын

Also the case for stroke adjustment on some Shimano MTB brake levers. Only JIS will do, a standard Phillips will cam out and destroy the screw (and potentially scratch your lovely titanium-look XTR levers). I'm pleased current Shimano mechs have finally switched to hex head screws for limit adjustment.

Using metric keys/wrenches on imperial bolts and nuts (and the other way around).

Cross threading. Using a tool with leverage to tighten something before it’s done up by hand as far as possible

#5 was one of the first things I'd ask a new hire to do if they said they wanted to work in the shop, and not just on the floor.

Lude my mate always lubes his bike wrong

nice nice

Calvin is there anything I CAN'T repair with the HMR-4?

Calvin looks like he needs a vacation from taking phone calls