Good video guys, very helpful tips for seasoned riders and especially new ones, great job!! Sure, wish we had these bikes when I was young. Dale

Great video that many of us have been looking for, thank you!

@RyderSigety

21 күн бұрын

Glad you liked it Tom, working on our next one as we speak

Great video guys!

@RyderSigety

16 күн бұрын

Thanks so much!! I please subscribe for more set up videos!

All joking aside I know Mike and he has always took time out to help out other riders from new to older and he has been around the track more then once He has helped me out more then once Thanks for all the help and tips...

@RyderSigety

21 күн бұрын

Right on, best wishes! Sounds like this is all old news to u, but thanks for watching!

This awesome! I struggle with the front axle on the TM and I think they are binding since last tire change. Sorry again about the confusion at the check yesterday. Great see you guys!

@RyderSigety

21 күн бұрын

No worries! Great day yesterday! THanks for all that u do. hope to ride with u sometime

Finally, I have been waiting for this video!

@RyderSigety

21 күн бұрын

Thats awesome! Anything help?

@noahbanewicz8287

21 күн бұрын

@RyderSigety the Sud frame mod and the guts seat. I was looking for ways to lower the seat height. and some of the jd jetting. I haven't gotten it right since it warmed up. Thank you so much!!

@RyderSigety

21 күн бұрын

@@noahbanewicz8287 u will be good now!!

I am way slower than your kid, so my jetting is a bit different. I found the midrange to very rich on my 24' YZ125X, so I bought and measured a few different needles. The Suzuki NExx series of needles is leaner at 1/2-3/4 throttle, so I use a NECW needle with a 52 pilot and 172 main. I do a lot of trail riding with the gf, and this jetting is a happy middle ground for my c/slow b class race pace and trail riding with her. Great video with lot's of info. Thanks for putting in the time.

@RyderSigety

19 күн бұрын

Thats great u get to ride with your GF and thanks for sharing and commenting and nice words!

The one radiator cover product looks like the fiber mesh used by stucco installers as a reinforcement. Not sure what they call it. I use the gutter-guard plastic mesh. Important to leave some pouching of the material during install so the material can flex which helps shake off mud and grass. I also leave a small bit of it loose at the bottom for the same reasons.

@RyderSigety

22 күн бұрын

Great advice, I didn't think I would actually learn by sharing info, but what you say makes sense, thanks!

Nice, video with some great setup tips for the Yamaha's. FWIW, I spent a bunch of time jetting a friend's 23' YZ125 last year. The biggest problem with the Keihin carb on that bike, is the slide. They are trying to share the carb with the 250, but the slide is just too lean to be effectively used in the 125. Once you put in a richer slide, I was going back and forth between a 5.5 and a 6.0 slide, Ideally, I would just cut a 5.5 into a 5.75 and be done with it. It really opens up your jetting options. On another note, Those bikes are very sensitive to altitude, so you're looking at dropping the main jet probably 2 sizes for Snowshoe (as your jetting stands now) The pilot and needle should be good though.

@RyderSigety

20 күн бұрын

Wow, sounds like you know your bikes!

@chintzygarage2819

16 күн бұрын

@@RyderSigety Hello Ryder, I will use your code to get a couple of GUTs seats. Thank you. As Michael mentioned , try the richer 6 slide and a CCL needle. Curious what you think vs JDs kit. It has by far improved jetting over anything I have tried. I have the GYTR(Y4) kit, but have not tried the JD kit. kzread.info/dash/bejne/hnh6qdiupKfQp9I.html

It would be nice if you could measure diameter and taper starting position of jdkit needles

@RyderSigety

7 күн бұрын

Interesting

@loremipsum6984

5 күн бұрын

Mentioned yamaha NYCH diameter is 2,72. Same diameter needle from ktm is NOZH. But the taper position of this two are different, yamaha needle is more lean. So it would great to compare them to jdkit blue needle

Thanks for the tips. Are the DT1 air filters available for Beta’s? I looked on there website and can’t tell

@RyderSigety

21 күн бұрын

i just checked and yes! GO here mxfilters.com/BETA-Air-Filter-_p_99.html

Great video.....We wanna know about the Y4 needle!!! ;)

@RyderSigety

21 күн бұрын

Yessssss!

@greg042

20 күн бұрын

We talked on FB in a yz 125 group. I never tried anything but the GYTR kit from Great Britain. It really helped, but that, the VHM head and Get ignition made it my Go To bike. My 250's and 450's here at Club sit. It's by far the most fun bike to ride! The kids here at Club have rode it. So much better than the new FI Austrian bikes, or so the kids say when they try it. Don't know how your video showed up, but I liked some of your tips. Think my wife's 125 is going to get that sub frame mode. Looks like the OLD JGR subframe trick Nice video ❤❤

@RyderSigety

20 күн бұрын

Sooooon! And thanks!

@RyderSigety

20 күн бұрын

​@@greg042thanks! Yes that's exactly like jgr mod, you know your stuff. We are hoping to get a complete gytr kit from Yamaha, I'd be very curious as to your detailed report on the entire kit.

Man that's some good info on this video!! Sold me on a few of these products!! Looks like the mika and dt air filters codes are expired just fyi

@RyderSigety

18 күн бұрын

Glad I could help! i just contacted Mika and DT-1 to see whats up with thier codes and they said they should be good by end of the day, ill let u know

@barkeep25

18 күн бұрын

@@RyderSigety works now!! Just ordered some stuff and made sure to mention your name !!

@RyderSigety

17 күн бұрын

​@@barkeep25wow thanks!

@barkeep25

17 күн бұрын

@RyderSigety no problem, do you happen to know the brand of that chain guide gaurd? I can't seem to find it.

@RyderSigety

17 күн бұрын

Bullitt proof designs makes a very good one, the one in the video is by a company called nice cnc, someone else has the same question I'm working off a phone so I can't find it exactly right now but it's in the comments here with a link ​@barkeep25

Got the y4 needle coming this week. Pro circuit called me yesterday and finally got them in. The carb in my son’s 23 came with the mid block gasket leaking air and no oring on the air screw 🤦‍♂️. It was leaking air everywhere. I tried the jd kit but was way to lean for me it was just bogging to death off the bottom. Could have been the air leaks but jd was no help and said I was doing something wrong so I sent it back. I will be trying the y4 with pro circuits jetting specs once the needle comes.

@RyderSigety

19 күн бұрын

Sounds like u do a lot of testing too. My dad said he read about someone with a bad carb on fb, maybe that was u? Please report back here with ur Y4 testing. thanks!

@SoCalMisfit712

19 күн бұрын

@@RyderSigety as soon as it comes. Jetting on the bike was miserable, I tried slides needles everything. They say the y4 is cure all we will see. 🤘

@RyderSigety

19 күн бұрын

Good luck!

Can you post a link for the Chain Guide reinforcement?

@RyderSigety

21 күн бұрын

Here ya go! bulletproofdesigns.com/yamaha-swingarm-guard-2012-2024/

@glassapology

21 күн бұрын

@@RyderSigety Thank you!

what is the tape you use on the levers? Is it tacky?

@RyderSigety

19 күн бұрын

any tack tape

oh boy there's a brand new 250 thumper sitting in the driveway!!! I'm betting you will like it for 1-2 races and then the 2 stroke will come back out of the truck

@RyderSigety

20 күн бұрын

idk why, but i love all the bLU bikes when i ride them.. Thanks for the comment Peter

@peterstebbins1815

20 күн бұрын

@@RyderSigety like your Dad said, they are the best bike for what you guys are doing.

@RyderSigety

20 күн бұрын

@@peterstebbins1815 Thanks, ill let him know u agree

Where is the option to add and send tips?

@RyderSigety

19 күн бұрын

Right here.

The Alco discount code is invalid. Do you have an updated code?

@RyderSigety

19 күн бұрын

dammm ur right! I just texted Alco, let u know when its corrected, sorry Aaron

@RyderSigety

19 күн бұрын

working now, again, sorry about that.

what abt an 85

@RyderSigety

21 күн бұрын

WOW we really should have done that when we had a slew of them. I wonder if we can borrow a bike and go over a list...

Not gonna watch this because I don’t have a 125 but I will make my dad😂

@RyderSigety

21 күн бұрын

yeah, u show him! actually u can use a lot of our ideas on any bike

How to make your yz125 a better bike Buy a YZ250 lol

@RyderSigety

21 күн бұрын

haha, my YZ125 plenty fast for me~!

Great video guys!!!

@RyderSigety

21 күн бұрын

Thanks so much Sergio!