One of the most thorough installation videos of planar / autotherm 2d that found so far👍 (and i have the same impact gun 😁)

Thanks for taking your time to make our lives easier! I will mount one myself with your previous tutorial! Greetings from Norway

Video has been a great help. After watching this I bought the autoterm planar and fitted it to my T5. Really good video and description which defiiitlet swayed me into buying me fitting this model👌👌 Now it’s on I’m very happy with it, a good quality item, easy to use, runs very very quietly and gives out great heat! Thanks!!!

Hi Owen, thanks very much for these overviews. I fitted the 2kW heater on the weekend. As a side note, the vents it came with needed a 64mm and 70mm hole saw, as there is a step in the vents now. You mention this in the video. Thanks again

Great job ! Loads of useful info and a great help.

First video I saw on installing a diesel heater that was actually helpful, and this was the 6th or 7th I watched... Great explanation!

@Heatersandfridges

3 жыл бұрын

There are a lot of people putting poor installation videos up and people follow them and do and awful job. Its why I made this video. I have personally installed hundreds of these heaters and fine tuned the position of everything to get to where it is now. It works perfectly now. It took two days to make the video during the first lockdown but I am happy with the final result. Thank you.

@Fidgester

2 жыл бұрын

I agree great video thanks

Really helpful clear instructions. Would’ve like to have seen dropping tank and connecting fuel. And all wiring up done too. But honestly thankyou for putting this video up👍

@Heatersandfridges

3 жыл бұрын

Check out the rest of my videos. There are more that cover this job.

A top video, makes installation of this unit into a VW T5 as easy as it can be. Just get armed with the correct tools, and a decent space to do the work. We will publish our install diary in an issue of Advanture Magazine

very good found this most helpful.

Thank you so much your vídeo was very useful for me!

Excellent tutorial 👌

When installed correctly there will be no fumes at all.they put out a tiny puff of smoke out of the exhaust when starting and stopping but during running there should be no smell at all And noise is very minimal. Less noisy than a standard household fan heater.

I managed to adapt a VW bracket for A Transit Custom. It'd be great if you could produce a specific one that utilised the AdBlue tank mounting bolts - remove bolts slide in your mount and put them back. Helpful video all the same.

Brilliant video of how to do this installation. Thanks

@Heatersandfridges

3 жыл бұрын

No problem at all. Something good to come out of lockdown 1.0

Very helpful video

Can I ask what size The self drilling bolts were to hold the underslung mounting bracket were? Thanks good Video

On an underslung installation, should one duct (the main heat outlet) be inside the can and the other duct be outside or inside the van? I have one installed and the heatering duct is inside, but the other one ism just left open, outside to the cold air?

Bravo

Great video... Can I ask what is the black spray used arounf the duckting and also what did you use to treat the metal holes after cutting and what size Teh Screws did you use?

@burnerofbiggerthings

3 жыл бұрын

I ended up buying two small pots of primer and colour mathed paint. In little Tip-ex style pots with a built in brush. The black spray I used is Waxoyl.

how long does the install usually take when having fitted under the van ? thanks

Hi Owen, a really good easy to follow video, thank you. I am wondering about if it is possible to bring the air outlet out of the B pillar by the seat belt mount. It looks possible from the underside but may be a bit tight ?

@Heatersandfridges

3 жыл бұрын

Its definitely possible. I have seen it done but not done it myself.

@mcjjordan

2 жыл бұрын

You mentioned it can go up by seatbelt - is there a picture of where it comes through from inside?

Hi Owen, I am looking at buying a Luton box van and converting it into a campervan. Probably a Ford transit. I hope to take it skiing in the French alps for a month at a time in the freezing temperatures. Would an underslung planner heater be able to function in sub zero temperatures? Also is it possible to box it in so no debris from the road can hit it? Could the exhaust from heater be extended to the very rear of the van? Where are you based please? Thanks. Michael Lewis.

Absolute brilliant, clear video. One question before I attack this... Can I have the outlet pipe come up between the two front seats and point towards the back of the van? Reason is I'll box this in where the hand brake is (Keeping clear of hand brake)! and just have the vent hole in the boxing aiming rearwards. Thank you in advance.

@Heatersandfridges

3 жыл бұрын

Yes, thats no problem at all.

quality job

Where about on the exhaust did you fit the insulating sleeve please?

Thanks for making this video! I had thought of mounting it underneath to reduce cab noise but was worried it would then be louder on a campsite near others; what's your verdict on the noise levels vs in the van? Thanks!

@Heatersandfridges

Жыл бұрын

Noise levels are always quieter with the heater fitted inside the vehicle. Its quieter outside and inside. The ducting seems to transmit more noise inside.

Hey there. Great video! Do you recommend to fit this underslung the VW or inside under the driver seat? Witch way is less noisy inside the van? After you fit it underslung, the covers will fit back over the heater as it was? Thank you

@Heatersandfridges

3 жыл бұрын

Under drivers seat is quieter generally and much safer for the heater but space often means we have to fit underneath. Make sure the trays are complete before deciding as this can add a cost you weren’t expecting.

Excellent fitting video. One question. Do you think the fuel pump cable could be cut shorter. That's a lot of excess cable. Thanks.

@Heatersandfridges

2 жыл бұрын

You can do yes but it gives no adverse effects and when people self fit it often causes problems due to bad joints etc. They come plug and play for a reason.

So I would be concerned with fumes and noise. How does something like this work regarding these factors?

Hi what size is the ducting did you use. And can you use the green fuel line instead Thanks.

Tool list: 7mm socket 8mm socket 10mm socket 13mm socket “Star clip” = T20 or T25? TBC Flat head screwdriver Tech screws or rivnuts (not supplied with kit) Angle grinder Exhaust paste (optional) *64mm & 70mm hole saw - Important - the video is out of date and they now use a stepped grill similar to the eberspacher as described in the video* Rust proofing for hole (paint)

Great video. Wish I’d seen this before my install. Question: the hole in the heat shielding for the exhaust is this a feature of the T6 as I don’t remember seeing it.

@Heatersandfridges

4 жыл бұрын

Marionville Multirotors thank you, yes its also on a T6. The heat shields are exactly the same on a T6 and the covers are also identical.

@MarionvillemodelsMultirotors

4 жыл бұрын

Yes I had a look under and can’t believe I missed the hole. Another question. The exhaust hose you use must me different from the Chinese heaters as I cut mine to day to copy your install and no longer fits the exhaust. The plane flanges at either end are slightly bigger than the concertina section. I’ll need to order another.

@ianchrisstewart

4 жыл бұрын

Hi Owen, what size tek screws do you use. Seems like quite a big hole.

@Heatersandfridges

3 жыл бұрын

@@MarionvillemodelsMultirotors hi yes chinese exhaust is a different size and not as good long term. It rusts away. Better to change for a decent one.

@Heatersandfridges

3 жыл бұрын

@@ianchrisstewart they have an 8mm head and 25mm long for the plate and exhaust parts. The pump can be a bit longer maybe. I have a selection.

Fantastic video I'm currently installing a diesel heater under my t5. Tell me does the hot air outlet pipe become very hot. I'm actually going to put the hot air outlet through the drivers step. My heater doesn't have a return pipe. The actual screw cap holds the heater lid on. Your video is perfect by the way very well explained.

@Heatersandfridges

2 ай бұрын

Hi. You definitely need to install the return air duct as per my video. You just remove the cap and the ducting will hold the heater together. Use a jubilee clip to make sure it stays on but don’t over tighten it and distort the casing so it touches the fan. Im assuming the heater is Chinese as you have that type of cover so they do run very hot outlet temperature. An outlet in the step will quite possibly melt the door card with a Chinese heater. I would exit via the seat base if possible. I have another video showing a few possible outlet places.

Where are you based for fitting Owen?

Owen have you tried connecting the fuel supply line into the return fuel line from the van engine.... Heard this is a way rsther than dropping the tank?? Pros n cons??

@Heatersandfridges

3 жыл бұрын

It only works on the latest T6s I believe. It definitely does not work on T5s as the return does not go to the bottom of the tank. Its not a big job to fit in the tank so we always do that.

What size Tek screw are you using ? Thank you

Hi Owen, thanks for your video. Should you mount a fuel filter as well?

@Heatersandfridges

2 жыл бұрын

In a vehicle installation there is no need. They cause more trouble than they save. On yachts they are required. The fuel sits around much longer on a boat and bacteria grows and causes problems on boats. Road vehicles tend to have a dip tube which is cut short of the bottom of the tank so any dirt does not get sucked up anyway. Just run it every month for 30 minutes to stop bacterial growth in the heater fuel pipe. This will avoid blockages.

HOW MUCH TO FIT ONE OF THESE TO MY VAN?

I'm wondering if they will run on a veg oil mxture like the oil diesel cars?

@Heatersandfridges

2 жыл бұрын

They will but not for long. They will soot up so it’s not approved for use.

Hi, great video, but I'd like to install mine under the driver's seat. From the instructions it looks like the turret plate supplied isn't used, so I'm a bit confused! It's a T5

@Heatersandfridges

3 жыл бұрын

Have a look at my other videos. There is a turret plate installations too.

Hi, great job! what's the cable protector called?

@Heatersandfridges

3 жыл бұрын

It comes with our looms pre installed but its kopex.

what is a gas drop out ? to watch out for when running the exhaust pipe

@granddadmark7639

2 жыл бұрын

Not an expert but when we bought our campervan we were told not to block the gas drop out vents in the floor (cupboard under the gas hob) which provides a safe route for any gas leaks to disperse as LPG Gas is heavier than air and will drop downward through the floor vent. Hope this helps.

Thanks for sharing this ! just one question, following the constructor notice the distance between the fuel tank and the fuel pump should be 1meter max no ? in your installation you seems have more than that ? thanks

@Heatersandfridges

3 ай бұрын

Yes, correct, however I have installed hundreds of them this way and found no issues with the distance from the tank. It’s because the pump is actually below the level of fuel in the tank and the pipework goes uphill after the pump. I would actually be surprised if the distance from the pickup to pump is more than 1.5m so only 0.5m more than advised.

@bems5066

3 ай бұрын

@@Heatersandfridges thanks

Great video 👍. I notice you don’t install an inline filter between the fuel tank and the pump . Is there a reason for this ?

@Heatersandfridges

Жыл бұрын

Yes, the reason is its not necessary in a road vehicle. Its just another place to leak and the fuel is clean and gets changed often.

@philipharrison8440

Жыл бұрын

Thanks Owen. Makes perfect sense to me 👍

Is the return air part necessary? There's no mention of it in the manual and would really like to limit the number of huge holes in the floor if possible

@Heatersandfridges

Жыл бұрын

Yes it’s absolutely necessary. Its not in the manual because the heaters usually are mounted inside the vehicle. You do not want to suck exhaust fumes and moisture into the living space

@ShadowV

Жыл бұрын

@@Heatersandfridges Thanks for the info!

Owen,thanks for this great video,but could you please tell me how to remove star clips?thanks Barry

@Heatersandfridges

3 жыл бұрын

Star clips?

@barrygiles8116

3 жыл бұрын

@@Heatersandfridges taking the under tray off there is starclips in places?

@Heatersandfridges

3 жыл бұрын

@@barrygiles8116 ah they twist off (at least most do) they kind of unscrew but some can be too rusty or damaged and you just have to lever them off. Good to have a few spares if doing it regularly.

@barrygiles8116

3 жыл бұрын

@@Heatersandfridges Thanks,i have got some just in case

Hi great video! Do you have monting plate for vw cady 2017 4M ? Cheers . Philippe

@Heatersandfridges

3 жыл бұрын

Thanks, we use a turret plate under the drivers seat. Mounted on its side of the footwell.

@Phil-dg1yg

3 жыл бұрын

@@Heatersandfridges tank you!

Super video 😉.. i have one question .. is there a reason ,to take the air from the inside cabin ,and not from outside ?

@Heatersandfridges

Жыл бұрын

Yes absolutely, you don’t want to bring cold, moist air into the heater. You want to circulate the air inside the van to make it more efficient. Also if you bring the air from outside you risk sucking exhaust fumes into the vehicle and making your own portable gas chamber.

@mulleboy2

Жыл бұрын

@@Heatersandfridges thanks for answer ..

great video that owen

Hi Owen. Great, detailed video! Do you not run a fuel filter?

@Heatersandfridges

2 жыл бұрын

No, no need on a road vehicle. We find it causes more problems than it solves

@neiljackson5137

2 жыл бұрын

That’s good to know! Thank you.

So how do you connect to fuel supply?

@Heatersandfridges

2 жыл бұрын

If you look in my KZread channel there is another whole video explaining it.

Does anyone know how to cut the exhaust pipe and where is the best place for the heat shield?

@Heatersandfridges

Жыл бұрын

Its all explained in the video. Cut the exhaust pipe with a grinder or hacksaw (grinder is easier). And the heat shield is not required on this installation if done correctly exactly as per the video. In any other installation install it anywhere the exhaust is likely to contact anything combustible. Although you need to try and ensure there is nowhere that it is in contact with combustible material.

@ShadowV

Жыл бұрын

@@Heatersandfridges Thank you! I have the external mounting box, do you know if it's better to have the connectors of the cables in the box with the heater (if they fit) or out of the box for easy access/ less heat? Also, does the fuel line get hot? Is it okay if it runs along side other cables? Do you know what the minimum distance should be between the ducting and exhaust pipe/mufler? Sorry for all the questions, the manual doesn't have any of this info

@Heatersandfridges

Жыл бұрын

@@ShadowV connectors are better in the box if they will fit. Make sure the heater is mounted the correct way up (wires out at top if on its side). Fuel pipe does not get at all hot if installed away from exhaust as it should be. All the important points are mentioned in this video. No matter that its for a VW they are all essentially the same.

Is it possible to fit under passenger seat on VW T6 ,

@Heatersandfridges

Жыл бұрын

Usually no, its only possible under the drivers seat because the adblue tank is under the passenger seat on a T6. (RHD) i have another video on how to install under drivers seat.

@justineknight3580

Жыл бұрын

Thank you for replying Owen ,

Did this install have a fuel filter fitted?

@Heatersandfridges

3 жыл бұрын

A fuel filter causes more trouble than it solves in a road vehicle installation when coming from the main tank. Not required as the fuel is all clean.

@garrychapman3224

3 жыл бұрын

Good to hear thanks, just fitting one of your heaters 👍

My undertray has damage, and concerned heater will be affected. Do you have a part number for a new tray? Thanks

@Heatersandfridges

3 жыл бұрын

Sorry not got it at the moment. tPS will give it to you from your chassis number on request.

Why not just use rivnuts? The second I see tekscrews it just shouts shoddy

@Heatersandfridges

Жыл бұрын

Because it was made for self installers to do easily with tools they may already have. I mention in there that rivnuts can also be used. Its a matter of choice. Thanks for the comments.

Any feedback now its months down the line... Are you pleased with the planar...

@Heatersandfridges

3 жыл бұрын

I have to say as the distributor I an probably biassed but I think we have many hundreds or even thousands of happy customers now. You cant go wrong value for money wise. More expensive than poor quality heaters and cheaper than the ones with a name tag. Just the same quality as expensive ones for a lot less.

@linoleumbonypart385

3 жыл бұрын

@@Heatersandfridges ahhh I didn't know you were... Good to hear... Just the fuel tank dropping is a worry...

@Heatersandfridges

3 жыл бұрын

@@linoleumbonypart385 there is a video for that too. Have a look in the library.

@linoleumbonypart385

3 жыл бұрын

@@Heatersandfridges does it come with all nuts n bolts needed for fixing... I've got a handy son so we can do it together

@Heatersandfridges

3 жыл бұрын

@@linoleumbonypart385 You get everything except a few 25mm long tek screws.

The heaters are reliable but be careful what company you use to purchase this from.

@Heatersandfridges

3 жыл бұрын

www.planarheaters.co.uk is our webshop as per the video. We are the sole UK distributors. Guaranteed to be genuine UK market models with two years warranty which can be increased to three if fitted or checked over by an official service centre.

It was going so well untill he said, he use tech screws

@Heatersandfridges

Жыл бұрын

Well all I can say is I have seen rivnuts corrode and fall out and none of my tek screws have….

@Heatersandfridges

Жыл бұрын

But as i state, you can use rivnuts if you wish.

Autoterm with comfort controller (comfort so the wrong word) Worst product I ever bought. Unreliable no connection in the digital display. The installer and the manufacturer arguing between themselves who and what is causing it to be £1000 of trash

@charliegee777

10 ай бұрын

Why, can you explain your issues please as I'm looking at getting one of these.

@under2boots

10 ай бұрын

@@charliegee777 unfortunately my issues remain - you go to use it and it comes up no connection in the display. So you wake up freezing and cannot switch the heater on. The distributor who initially reached out to help is proving just as unreliable as the installer. With my experience of Autoterm, I do not recommend unreliable product with a 3 year warranty that so far has proved to be non existent. The last contact from them was that it was my fault for not living in the same town as their location. A complete waste of £1000