For all those, who have trouble with getting HAL_TIM_PWM_PulseFinishCallback() to work - You have to Enable the interrupt from corresponding DMA channel in NVIC settings category in Cube and set its priority. Otherwise, the interrupt is not fired and the function never gets called.

@ControllersTech

2 жыл бұрын

I thought the interrupt is automatically enabled once you enable the DMA. I guess they have changed it.. need to check it again

You're a hero! Thanks!! Definitely the best resource on this topic I found on the internet

Great video! Thanks for the guide. I was actually reading the documentation and thought of doing something just like this, but since there was a tutorial already just followed it and it just makes a lot of sense to read when coded.

@jakobvarney9357

2 ай бұрын

Did u buy the led strip

Excellent video! Only issue I have encountered is the excessive RAM memory utilization when driving 300 LEDs: 14.2 kiB. The best (but hard to implement) solution would be using circular DMA, but I couldn't be bothered. Instead you can also go back to the DMA configuration screen for the timer and say you want "Byte" data size at the memory size (and leave the peripheral data width alone, still "Half Word"). Then in code you can change the DMA buffer to uint8_t instead. This will half the memory footprint. Be careful what you pass to the the length parameter of HAL_TIM_PWM_Start_DMA, I suspect this counts in "data width" units.

For mapping apparent brightness to an LED duty cycle (the 8-bits per color channel in the WS2812 protocol), take a look at gamma. It’s basically an exponential scale. That should map better to perceived brightness than the tangent.

@valentineeze4777

2 жыл бұрын

Do you have a video tutorial on how to make it? I am interested. This video makes me want to learn more. What if I want to control more than 12 LED rings?

Thank you so much for the tutorial, it was perfect!

Fantastic tutorial, thank you!

Excellent video!

This is so freaking usefull and easy to follow.... :)

Wonderful video! Thank you very much :).

I don't know if I translated the code properly, but in my case I had to put the pixel data from MSB to LSB into the pwm array starting from 0, not 23 as in the original code... Excellent tutorial btw

Very nicely explained ...!!!

Thanks a lot!! After simple modification, I successfully reproduced on the bluepill board. F103C8 have 20K RAM can drive 333 LEDs (With Brightness adjustment) or 358 LEDs(Without Brightness adjustment) I think... If we use DMA's Half-Transfer Complete event (HT event) and Transfer Complete event (TC event) to DMA processing... Able to use less RAM and can drive more LEDs.

@hulyjoe

Жыл бұрын

Hi, can you please help me with the code modification for the bluepill board? Thanks.

@GuiMVII

Жыл бұрын

@@hulyjoe You just have to use TIMER2 with the same configs, for some reason there is an conflict using TIMER1 and external clock

you've on the logic analyzer a decoder for WS2812 protocols.

Great video. Question: Could you show me how to control a section (few leds) of the LED strip with a push button.

I successful made the project works on STM32F407, with Keil C IDE. One strange point that I noticed when porting is that the program would unexpectedly stuck at: while (!datasentflag), even this variable shows value 1 when in debugging mode. To solve this bug, I had to declare it as volatile variable like this: volatile int datasentflag=0; (with #define USE_BRIGHTNESS 0) Thanks you very much for this great tutorial!

@jakobvarney9357

2 ай бұрын

Question what files did u include with your project to run this code

Excelente!👍

You can do it without DMA. I've had the W2812B running with PWM on an xmega32. You use the "overflow" interrupt to update the duty cycle for the next cycle since W2812B timing is essentially PWM with 33% and 66% duty cycles for 0 and 1 respectively

@berndwacke7083

Жыл бұрын

That's basically correct, but using DMA you are offloading the task of updating the timer's CCR-register (PWM's duty-cycle) from the CPU to hardware (namely, the DMA). This way, you save valuable processing time for other (possibly real-time-)tasks, which may otherwise become delayed themselves.

@Sayeesh-kc5yy

11 ай бұрын

can you please bit elabrate the this idea

@TheEddie581

10 ай бұрын

@@Sayeesh-kc5yy the golden rule is: use the DMA controller when possible, in order to free the main processor for other things. your main chip is too precious to do just dumm byte sending and receiving. Of course, this scheme is only fully functional with the usage of an RTOS.

thanks!

Great video, Can I expect a video on UART parsing? Ethernet related And TI controllers videos

@ControllersTech

3 жыл бұрын

No TI, at least not in near future.. but yes I'll work on ethernet probably

Hi, I guess most of the video is correct. But please have a look at 11:54. You want to send 24 pulses. If you count those shown in the oscilloscope recording you find 28. I had a similar issue on a STML4 with 80MHz. It seems that the DMA callback invocation is simply too slow. I tried to put all the code into RAM but without success. The only thing that cured the problem is to stop the DMA and write a 0 length pulse and after that stop the timer. Certainly to configure a 25th pulse with 0 length will do the same because this will be the repeated value after DMA is not updating anymore. So you comment 'DMA doesn't stop' at 10:56 is actually wrong. The reason why PWM continous is because the timer is running. Therefore you don't need to stop DMA (it stops reliably after 24 updates of the CCR register of the belonging timer). However, you need to stop either the timer itself or the output of the belonging timer channel.

@TheEddie581

10 ай бұрын

You're quite right. The DMA callback routine takes a little time, enough to send an additional 4 pulses. I had the same issue (using an STM32F373 @ 72 MHz). My solution was to : a) put my LED code data in an array with 48 bytes offset data at the the beginning that only contain zeros, my real data at element data[48] and further. b) change the DMA mode from normal to circular. In this way, the DMA will loop back to the beginning and load the TIM OC register with '0' values (the offset stuff), therefore making the PWM output value low until the callback routine is triggered by the NVIC. My pulses are now a perfect multiple of 24 bytes. Also, you could make the DMA do data conversion, so store your led codes as bytes, then let the DMA covert them to words. This really shrinks your memory usage if you have a lot of LEDs in the string : dmaInit.PeriphDataAlignment = DMA_PDATAALIGN_WORD; /* UInt8 ==> UInt32 ! DMA doet de konversie.*/ dmaInit.MemDataAlignment = DMA_MDATAALIGN_BYTE;

Great

Thanks a lot! I'm going to try this tomorrow. Thank you

Very nice

Hello This is South Korea.

@oldchannel8148

Жыл бұрын

hello

How to use logic analyzer for debugging please let me know?

Im using this method and try to control more LED strip ( 8 led strip with 64 led on each strip). Im using STM32F407VET6 with 2 different timer and DMA set like you did. The led strip now is only shining half the number of LED on each strip. I think this is because limitations of DMA. Can I try this with using DMA burst feature ? And if you could do you have any document or example of using DMA burst transfer.

Thank you! Got it working on the F031K6 board, I had to use the HSI clock instead because the board dosesn't have a external xtal. I also had to modify a few of the calulations but go it working just fine in the end. The only really question I have is I ended up having to modify the effects code a little bit to get my WS2812 LEDs to work. I ended up having to increase the strip count to double +1 what I was actually using. If I went 1 over I would only get one LED to light but my board had 7 LEDs so I had to set it to x15 LEDs to get it to work. This was this line of code I had to change in the begenning of the for loop in the effects code. for(uint16_t j=0;j

@ControllersTech

2 жыл бұрын

effect code was just for fun. Even I was surprised when I got it to work. And obviously I don't know what's happening inside it, as I never tried to find out more about it

Why do you need an extra cell 0 in LED_Data? The LED number is already clear from the array cell number :/

I have one extra bit in the beginning and I can't get rid of it

hi Controllers Tech, I am very new to microcontroller programming. I have question on the effect of why you initialized pwmData[24] as uint16_t type on line 67 in main.c and then when starting the HAL_TIM_PWM_Start_DMA function in line 80, you then cast it to uint32_t pointer? How does this affect the data stream? Sorry not sure I get this part.

@ControllersTech

2 жыл бұрын

Initialised with 16 bit because that's the maximum length of the data we can send. i used a 16 bit timer right.. Hal pwm start dma takes 32 bit parameter, that's why needed to typecast

Great job!!! So You decidet to publish PWM solution first. :-) I have a question about peripheria clock source (1min 39s). Can You give a link STM32 clock source diagram or which secion in datasheet contain theme?

@ControllersTech

3 жыл бұрын

I a snapshot from cubemx

How do you think is it complicated to create FTP Server with STM32 + ENC28J60 ? This could be useful for backup files. Thank you.

@ControllersTech

3 жыл бұрын

Don't know haven't worked on it... Don't have the module

llike it

Hello, How can I make the LED strip start from a non zero. Example I want my LED to start from the forth (number 4) LED on the strip instead of number Zero. I did try to use range. The code compiled but it didnot run on the stm32. I need help.

@ControllersTech

2 жыл бұрын

You have to keep the first 3 of them to 0. They are connected in series so you have to proceed in that manner.

@valentineeze4777

2 жыл бұрын

@@ControllersTech Hello, Thank you for the feedback. I did try this it worked. The difficulty that I am having using a range to do it, instead of hard typing the whole SET_LED one by one. Please help. If there is a video tutorial on LED i will gladly use it. I just want to do more.

You can choose to do the hex color setting with this void Set_LED_HEX(int LEDnum, uint32_t colorValue) // { LED_Data[LEDnum][0] = LEDnum; LED_Data[LEDnum][2] = (colorValue >> 16) & 0xFF; // R LED_Data[LEDnum][1] = (colorValue >> 8) & 0xFF; // G LED_Data[LEDnum][3] = colorValue & 0xFF; // Blue }

what a good video, thanks I needed it although I have a question is it necessarily to use DMA to send data?

@ControllersTech

3 жыл бұрын

You can use other things like spi, or timer interrupt. But with dma, the cpu remains free for other work

@andresceballos1451

3 жыл бұрын

@@ControllersTech OK thank you

@edwinvp

2 жыл бұрын

Been there, tried without DMA (using just GPIO pin registers): it was barely working. And if you have also interrupts for other peripherals, forget about it.

@Sayeesh-kc5yy

11 ай бұрын

hey hi can you please explain how did you do@@edwinvp

@edwinvp

11 ай бұрын

@@Sayeesh-kc5yy I used the STM32F072RBT chip. Inside my program I converted the RGB values for each LED to a long array with PWM data that the timer peripheral would understand. Then a DMA memory transfer would send the data to that timer which would generate the pulse train on the h/w pin. I have sources if you are interested.

Hi! i have problem with HAL_TIM_PWM_PulseFinishingCallback. When I call it, no pwm pulse is generated. Can you help me.

@ControllersTech

2 жыл бұрын

You don't call it. It will be called automatically when the pulse is finished

@vantuyeno3161

2 жыл бұрын

Thank you

Hello, for unknown reasons I have problem with "HAL_TIM_PWM_PulseFinishedCallback" function. I don't know why but my f429zi won't execute this callback and stop DMA. Any idea why can it be so? DMA data is sent but PWM wont shut up. :-) And HAL_TIM_RegisterCallback is disabbled in c file.

@silelis1980

3 жыл бұрын

What is most strange sometimes this interrupts works but when I change some setting it dissapears in next compilation ... :/

@silelis1980

3 жыл бұрын

I had connected my nucleof411R E tyo check it and "HAL_TIM_RegisterCallback" is working. After that I connected nuclewof429zi and it also started to work.

@ControllersTech

3 жыл бұрын

You are using rhat transferfinished variable right ? Because if you load pwm with another set of data, it will keep going..

@silelis1980

3 жыл бұрын

@@ControllersTech Funny and strange thing. I made some additional ivestigations and tests and noticed that: void HAL_TIM_PWM_PulseFinishedCallback(TIM_HandleTypeDef *htim){ HAL_TIM_PWM_Stop_DMA(&htim1, TIM_CHANNEL_1); HAL_GPIO_WritePin(LD1_GPIO_Port, LD1_Pin, GPIO_PIN_SET); //I add this line to test callback execution } is not executed in debug mode (LD1 led is not lighting) BUT when I run program HAL_TIM_PWM_PulseFinishedCallback is executed. Do You have idea why is it so?

may i ask where is the variable color at 8:44 come from?

@ControllersTech

Жыл бұрын

check 9:57

This works with LED strips ?

@ControllersTech

2 жыл бұрын

if the driver is same, then yes

Unfortunately, it didn't work with my processor stm32f030f4

@ControllersTech

2 жыл бұрын

If it have DMA and timer, then it should work as usual

@fadial-baghdadi6157

2 жыл бұрын

@@ControllersTech Unfortunately i try a lot

@fadial-baghdadi6157

2 жыл бұрын

@@ControllersTech I have question about how I can change idel from high to low

Nice video. But when I try to put LEDs in a loop it doesn't work. It stays same as start up colors. How can I fix this?

Çalışmıyor hiç boşuna uğraşmayın

You are way too fast for a "tutorial" in the section of CubeMX, expecially in the part of clock selection. What, why? Nothing really explained. And why the computer generated voice? DMA control is cool though!

@ControllersTech

4 ай бұрын

There is nothing to explain there. Anyone who used the STM32 mcu would know how to configure clock.