Love the trash talking.....lol just like working with my dad.....😅

@hammersgarage

10 ай бұрын

Lol, glad you enjoyed it, thanks for watching!

I could watch this guy all day 😂🤘🏼🇺🇸💪🏼

@PrimeG2

15 күн бұрын

For real lol, funny guy right

The boss you around booklet. Love it😂

@hammersgarage

Жыл бұрын

Thanks for watching!

@10:40 had me in stitches

@hammersgarage

Жыл бұрын

Thanks for watching!

@TorqueMediaau

Жыл бұрын

@@hammersgarage FYI, nappa part number 10077 is a 3/4 to 5/8 hose with a right angle at the firewall side that will perfectly suit the application.

The best video I have seen on how to install this system. Thanks!

@hammersgarage

9 ай бұрын

Glad it helped, thanks for watching!

Very nice truck and well done sir!

@hammersgarage

14 күн бұрын

Thanks 👍

Recently just finished my vintage air project - universal 86 c10 gen IV😅 tips 1) I’m not what you would call handy .. 2) mechanics recommend a 20 hr project- 40- 50 project for me 3) the template was a disaster for me : ended up just cutting a huge hole in the fire wall so the holes didn’t have to be exact and would give access through the engine compartment vs being forced to tak it out if I had problem 4) would recommend taking the seat out 5) didn’t use the duct work under the steering wheel and used extra 2-3 tube to extend it 6) I needed an extra hand to mount the condenser 7) you will need a drill and you will be drilling a lot of holes 8) if you have a stock engine or what not , the compressor will be on the drivers side( but the hoses were pre crimped ) 9) the compressor bracket was a pain , and to loosen the the power steering pump 10) wiring was intimidating but once I laid it out , it made sense ( directions were good ) and spliced into the radio hot wire for power 11) hoses are small and used zip ties and aluminum duct tape 12) you will need to cut the glove box for it to fit , but it will still be functional 13) you will have to run all power directly to the battery 14) condenser didn’t line up exact , so I did take the radiator out and the grill off 15) you will have to be creative with the belts ( vintage told me to buy a few belts and go use the trial/ error method Did end up cross threading the compressor All in all I got about 90 percent finished and took it to vingate air dealer to finish ( my water pump needed a new bracket ) it would line up correctly I did save about 2200 dollars by doing it myself and I am very in tune w/ my truck and learned a whole lot - 😂😂😂😂😂

@michaelhood1291

3 ай бұрын

Would you do it yourself again or spend the $2200. I’m looking at being in the same boat you’re in.

Glad to see a new video!!!

@hammersgarage

Жыл бұрын

Thanks for watching!

… and great video. Most videos show truck in complete restoration stages , so they have a lot of room to work with. This was more spot on

@hammersgarage

4 ай бұрын

Thanks 👍

This guy is funny asf “oh I’ll just throw these lose screws on the ground I’m sure they won’t go no where”

Very helpful video

@hammersgarage

Ай бұрын

Thanks!

Great content

@hammersgarage

Жыл бұрын

Thanks Mike!

Great Content!

@hammersgarage

6 ай бұрын

Gracias!

It was told to me that when lubricating o-rings for AC systems to always use the same oil that the AC system uses so not to contaminate it.

Flipping awesome

LOL at 21:50 i like that man , did you do it :)

@hammersgarage

Жыл бұрын

Yep, all me!

@hornetbad

Жыл бұрын

@@hammersgarage by the way. I am now seeing all the videos for this truck build man LOVE it , keep it up 👍 and yes I subscribe for sure

The link to the kit isn’t populating. I’d love to see the full kit you used as I’m about to go down this route. Thank you!!! Great truck

@hammersgarage

4 ай бұрын

I updated the link, but try this one and select which kit you want; www.vintageair.com/surefit/complete-kits/?make=Chevrolet&year1=1985&model=Truck

@Drakes_Garage

4 ай бұрын

@@hammersgarage thank you so much!!

Fantastic video! Can you tell me how much (real life) time you have into this instal?

@hammersgarage

3 ай бұрын

Basically a full weekend, but if I was totally focused on it without filming and such it could have been done in a day.

Hey brother, I am not running the vintage air, but I did have a question on the factory air system. I was wondering if it’s possible to keep exhaust smoke at stoplights from being pulled in while running the AC or heat my exhaust does not leak only happens at stoplights pulling in the surrounding Exaust.

@hammersgarage

Ай бұрын

Hmmm...that should not be happening. If you have no leaks I would look into where you are dumping, or if the smoke is coming from a small oil leak or something dripping onto the exhaust. Hard to say without seeing your setup.

@martinolivas319

Ай бұрын

I appreciate your response, I’ve just redone my Exaust so no leaks there and I’m dumping behind rear tires so that should not be an issue. I was thinking that maybe my blower motor was pulling in the Exaust from neighboring vehicles at lights or possibly through the vent in passenger kick panel

@hammersgarage

Ай бұрын

Maybe...try idling somewhere with no one around and see if you still get fumes in the cabin.

Hey, what's the paint code for your dark blue square body. I am ready to do a two tone with that dark blue. Thanks

@hammersgarage

Жыл бұрын

29/WA7349

@NorthGaKayak

Жыл бұрын

@@hammersgarage Thanks, I'm in Dalton

@hammersgarage

Жыл бұрын

Cool, maybe we’ll cross paths at a show or something one day!

Have you had any over heating problems

@hammersgarage

8 ай бұрын

No overheating problems.

If you don’t Mind me asking but where did you get your engine cover?

@hammersgarage

5 ай бұрын

Specialopsmotorsports.com

@NDB390

5 ай бұрын

@@hammersgarage OK. Thank you. Ever figure out the stumbling problem? Ever try spark plugs or compression check?

@hammersgarage

5 ай бұрын

@@NDB390 compression yes, plugs are new but someone did suggest different ones. Gettin’ ready to do a Holley Terminator setup on it, that should bring anything else to light. Thanks for watching!

@NDB390

5 ай бұрын

@@hammersgarage That could eliminate a bad harness. I’m restoring a short sq 4wd at the moment and did a 5.3 in it.

I'm trying to find a c10

@hammersgarage

11 ай бұрын

Just be cool, the right one will come!