I've been milling local lumber since 1982, first on a neighbor's 40" radial Foley Bellsaw powered by a Chevy 350, then with an Alaskan sawmill, and now I own an LT40. I have never found small dimensional, construction lumber (one bys through 2X8s) to be profitable. 4X8s and up are profitable and take much less time to mill. I would reach out to a few general contractors and let them know you can cut large beams and posts to order. You can offer them at a price that is profitable to you and saves them a lot of money. My most profitable milling was always live edge slabs. I would mill standing dead cedar and Doug fir into wide live edge slabs (16"+ wide, 6'-8' long, 2" thick). I would build a few live edge slab benches, load them and about 25 slabs into my pickup truck, drive to Grass Valley/Nevada City CA, park in a large pullout on the side of highway 49 or 20, set out a couple of benches and lean about 6 slabs standing up against my pickup truck. The slabs I would consistently sell for $75-$100 each. The plain (no back) benches I sold for $150. Benches with backs $250 each. I also received orders for slab tables that fetched $1,500+. That was in 1994. I now live in North Central WA. I recently sold an Aspen live edge slab table for $3,300 and two benches for $350 each. There are a couple of tree trimming guys down in the valley below me who will call me and offer me the butt logs off "yard trees" they are hired to remove. They don't want to mess with the butt logs, so if I come with my trailer when they call, they will load butt logs of maple, elm, walnut, and oak onto my trailer for free. I know a few woodworkers around the area, and occasionally I will call them and let them know I will be milling hardwoods "upon request" in an upcoming Saturday. I usually get 3-4 woodworkers to show up. I throw say a maple log on the mill and take off a slab to reveal the inside. The wood workers take a peak. I then ask, "what do you want me to cut?" I then mill the boards they ask me to right then and there. They love it, and I have a blast watching them drool and bicker over the boards. I have sold quite a few boards that way. Large (18"+ wide, 6'-8' long, 2"-4" thick) maple slabs can sell for $400 each. I've never tried to make a full blown business from my milling. It's more of a hobby that pays for itself and gives me a ton of enjoyment and has a social element to it as well.

@WilsonForestLands

10 ай бұрын

A lot of good information there. The trees I am working with right now to thin out the forest are not very big and not very straight. Occasionally I have been working with a few that are good for bigger timbers and those are what are selling most. But most of what I am working with right now is the type trees that just produce the smaller common lumber that isn’t that profitable. Those trees are just better to send to the commercial mills. Once I get those trees thinned out I can move on to better material then maybe pursue more of the timber material.

@Graybeard_

10 ай бұрын

@@WilsonForestLands With the smaller tops, I mill dunnage and cribbing. Heavy equipment operators love the dunnage and will almost always take some. I'll cut one 6X6, 7X7, 8X7, etc. from a six foot tree top, whatever it will produce. Dimension doesn't matter, really, whatever the top will produce. Wane on the corners is usually acceptable. Some will twist bad, so I cut those into 24"-32" long chunks. They are still handy for a lot of uses. I always have a pile of them handy, no need to even sticker them, as they're just gonna get abused anyways.

@j.jacobson

7 ай бұрын

Ride on we use to prospect all over California including French gulch last chance ext. I was born there in that place lol. Anyway I ended up after all my travels I landed in Tennessee bien here 21 yrs on and off,to get to my point I’ve got a wood business and rescently bought a mill and have lots of experience selling thing on the sides of highways involving wood so your story was cool for me to hear.

@j.jacobson

7 ай бұрын

I’m 43 years old trying to make my way same as the old timers.There’s a fair chance I passed you at some point down fishing on the American river.

@kurtdowney1489

6 ай бұрын

Have you heard of sealing the ends of fresh cut to prevent cracking and warping?

Never quit. Your in the best wood. I would cry in ontario to be cutting that, the mill is probably payed off just with the looks from your little pile of saw dust. Milling is my passion, cut in winter haul with skidoo stock pile for summer fun. Kept out of sun the wood is good for years and years. When lumber prices go up then your ready. Or build anything any size for yourself really cheap. Don't quit stay positive it's a great spot

I bought my LT40 Super in 2000 without having done a lot of market research. I'm in Indiana and saw hardwoods which were hard to locate in small quantities for the amateur woodworker. I built 3 solar kilns and a large warehouse. Despite not having done my homework, word got around and I spent as much time marketing as sawing. I can't say I ever thought it could be a highly profitable business but I love wood and selling to woodworkers and making enough that I haven't had to touch my retirement money. I will say that if all I had was an LT15 I would have given up years ago. There are lots of those around under tattered blue tarps.

@WilsonForestLands

7 ай бұрын

I think you have an advantage in that part of the country with all your hardwoods. I enjoy milling and working with wood and I’m glad to be back to doing it as more of a hobby.

@brinkee7674

7 ай бұрын

@@WilsonForestLands You have to make your money with custom lumber. A large beam should cover and then some of all the off cuts from the log. Sell them and it's all profit. Does make it tougher with your sized mill but everyone starts somewhere I guess.

As good as your videos are...the comments from other loggers and millers is an awesome add on...and thx for responding to so many of them....

@WilsonForestLands

7 ай бұрын

I do appreciate the comments I get. Some are a wealth of information. I do like to respond to them but I have been getting so many lately it’s getting difficult to keep up. Thanks for your comment.

I’m very fortunate to be surrounded by both softwoods and hardwoods. Hardwood is worth so much more for the same amount of effort.

@WilsonForestLands

9 ай бұрын

Yep that is where a sawmill makes a lot of sense, when you have higher dollar material to mill.

You make a lot of good points. I don't blame you a bit for cancelling any sawmilling.

Nice to see a honest review of the realities of a small bandsaw mill. In my area there are many people doing milling as a side hustle. The problem is, even the local smaller production mills beat them on price and quality. They always compare their price for hardwoods to Home Depot or Lowe’s, which they do beat however, they don’t come close to the small production mills. Having said that, I would still like to have a small hobby mill.

@WilsonForestLands

9 ай бұрын

Having said what you said and what I said, I am still looking forward to getting back to the mill this fall after wildfire season ends to do a little milling. It’s something I enjoy doing.

@mikeingeorgia1

9 ай бұрын

@@WilsonForestLands sometimes that’s all the reason you need

@jerrytalley802

7 ай бұрын

If I could get my physical energy back, I’d love to have even a small mill. One small project and the stater mill would pay for itself. I know a guy that restores vintage trailers, lives in Nevada, says a 1x6 or 1x8 x 10’ is like $24, crazy!

@mediumrare9051

6 ай бұрын

well considered.

@TheBurtle005

4 ай бұрын

That's the problem around here. There's a lot of woodmizers around. There are tons of guys who will mill for nothing. The cheapest guy is 65.00 per hour. The most expensive is around 150.00 per hour. The average mill owner is at 80.00 per hour in this area. I counted 20 mills open for business on facebook within two hours from me.

Such a heartbreaking realisation. Even when just doing projects around the farm I’m plagued with the reality that things will take 3x as long if I log it, mill it, and then build it. I want to build a gabled carport using questionable lumber, imagine the risk I’m taking parking my truck underneath it for the next 20yrs, not to mention the heartache of rebuilding it if the lumber doesn’t hold up. Already spent a few $k just buying lumber to build the sawmill shed so I didn’t have to work under sun. I drew a line in the sand at that point and said if I can’t build at least half a project out of milled lumber then I won’t build it. Thanks for hearing my rant! 😅

There’s a thousand things you could use the lumber to add value to it. You could build trusses. You could sell barn and shed kits. You could use the lumber to build modular homes. One thing for sure is it’s not going to cut itself down.

Good on you. The superpower of micro mills is that they can start up and shut down in response to market conditions. Georgia Pacific can't look at low lumber prices and say, "well, this is a good time for all twelve thousand people who support our sawmill to go on vacation, anyway." Even a small commercial mill has hundreds of people- workers, truckers, loggers- depending on it staying in more or less continual operation. But you don't have to coordinate with anybody but yourself and your customers.

Trying to make a hobby into a business isnt easy. But if you make your own doors / tables windows the mill is awesome. Also use it to make up window / door trim, cabinet material , large custom rafters / beams. Mostly not to sell . Your right about having a huge supply of pine . I noticed the blue stained pine is now in demand where a few years ago Mills wouldnt accept it. Cedar definitely the wood in demand if you can get it. One thing that is a problem selling wood is bugs in the wood that make a showing a year or two later with little piles of sawdust they leave behind on the floor. All in all I love wood milling.

Good job thinking thru the cost - benefit angle. Some guys just stick with doing the same thing & get bitter. Moving on to other projects makes sense. It’ll come back around. It always does.

I bought my saw a few years back but never with the thought of selling lumber , I realized that that market was not worth the effort . But I could design and build structures , gazebos etc that were more beefy then those built by the commercial sellers , sheds with unique designs etc that caught peoples eyes as unique .

Enjoy your time off. Look forward to new videos when you start back. Have a great vacation my friend.

@WilsonForestLands

10 ай бұрын

Thank you Timmy.

first mill I worked at was also an "exterior siding" mill. they would buy medium grade lumber in bulk from canada, plain it down a bit and put chemical and paint on it to sell as exterior siding instead of structural lumber. they turn quite the profit just from remanufacturing lumber into a different product.

Well I'm enjoyed your videos. brings back a lot of memories for me. I built a little sawmill in Clay County West Virginia in the 90s, before I came out to California. it had a 60 inch blade and a school bus motor set up a blower for the sawdust bought a four-wheel-drive tractor 6 foot high rear tires 4 foot high front tires bought and repaired a log truck wound up hauling logs for a local sawmill so I was out in the woods in the mud and snow on their jobsites driving logs back to the mill two or three times a day it was dangerous work and a lot of close calls a few saw cuts one particular time where where a log I just cut the top Free after falling it decided to walk me back 20 feet up against another tree stump 6 inches of squishing me like a bug it's starting to feel like like 10 years of riding dirt bikes with all the close calls anyway I quit the dirt bikes left the Mill I'm in beautiful weather in California and I've been here ever since now i ride mountain bikes gives me back a little piece of that takes me further out into nature! thanks for the videos!

@user-lb3ql1ef8j

10 ай бұрын

😊

@WilsonForestLands

10 ай бұрын

Sounds like you would have some great stories to tell. Thanks for the comment.

@mandy2tomtube

10 ай бұрын

@@WilsonForestLands Well, if you were my neighbor, I’d come over and help you and tell you a few stories how many years do you have? There was an old guy named Charlie Young his wife, ran the post office in Bomont Clay County West Virginia this guy was a millionaire lived in a single wide trailer on 1000 acres. He said his best day was when his dad came home with 450 John Deere bulldozer with a six way blade and the next morning he didn’t have to get up and feed the horses just get logs that man told me stories every day for a year helped me with my mill in every way possible he sit down on the floor in a sharpened draw out machines tell me stories I couldn’t of done it without him he was like a father to me a father I never had wished I had I’d love to tell you stories and help you catch some boards, but I’m down here in Southern California for the last 32 years stayed because I couldn’t believe that it’s the weather this good anywhere on the planet never managed to buy a home, but I never wanted for anything really other than a home I could call my own but I’ve had a good life I feel like the luckiest man in the world wonderful wife and wonderful daughter trying to figure out what I’m gonna do with the last 20 years of my life I ride mountain bikes every day you stay safe out there it’s been really good to hear your stories. Thank you.

Now that is using your head thinking about the future of everything you love. Good luck on your vacation and always have fun and get some rest.

@WilsonForestLands

10 ай бұрын

Thank you James.

Thanks for the video ---I've always wondered how having a small mill might work out. Wow! A good many tough comments. I appreciate your sharing the realities of that business. I live in urban Seattle and heat with wood. I have zero wood of my own, but nearby light industrial businesses throw of lots of scrap wood they are glad to have me haul home so they don't have to pay to dispose of it. Much of it is random lengths of dimensional lumber which I just cut to length on my table saw if needed. Also a lot of chunks that don't even need to be cut ---just tossed in the stove. Of course, wood heat is never "free"! There a lot of labor to that but as a retiree it's something I enjoy. I'm guessing that high interest rates cut the guts out of construction and the lumber needed for that. The big growth industry continues to be government and the taxes and debt that finance it. I shake my head in wonder with what goes on in California, which makes Washington State and Seattle look almost sane by comparison.

I was able to pay a guy to mill lumber, that bought his own mill. I thought that was a nice compromise in time vs money. His father sharpened the blades. So, I harvested the logs, and put up a small structure. I still bought 2x8's from the lumber store.

@ronbell7920

5 ай бұрын

Good move! I like to think about how much money I am saving running my own mill. If I include cutting, clearing, stacking, milling, drying, etc. Buying lumber is cheap! Its a lot like fishing, the most expensive meat one will eat is at the end of their line.

Enjoy your time off, you are spot on about the economy since 2020. If you don't mind me asking, what does Doug fir pay per thousand bf? Hemlock logs were through the roof last year. Worthless this year. White pine stays about the same give or take a few cents. We can sell all the 1x10's and 1x12's we can cut. It goes for cabin, barn, and shed siding. "Bat n board" 4- 1x12x8 boards with batting is a lot cheaper than plywood. Clear "no knots" 1x whatever, sell really fast as well and a higher price than siding. Like others have said, large timber's as well but handling them can be a pain. We enjoy your videos as I'm sure a lot others do as well. Hang in there.

@WilsonForestLands

10 ай бұрын

Right now DF is a little over $800 per MBF at the peeler mill. Just under $800 at the stud mill. That is for long logs Scribner scale. They were at about $1100 a while back.

@Twobrothersoutdoors

10 ай бұрын

@@WilsonForestLands wow! That is ridiculously high! Hard maple and cherry doesn't bring that here!

Wood Mizer nice units made Indianapolis. Just spent time Kalispell, White Fish and Missoula Montana and Cour d’Alene Idaho. There are a lot more custom homes being built northwest part of country than Midwest. Interest rates definitely holding down lumber prices. Enjoyed your video.

Wilson Forest Lands, my family has been in the Sawmill/Lumber business since 1948, and I’m 3rd generation in the industry. I own a Baker full hydraulic mill, with flip table, return belt, etc, for a two man operation to cut 6-7m feet per day. These lower lumber prices won’t last forever, and rest assured, when the demand returns again in the next few years, the price will go to excessive levels never imagined. The secret in the current low cost environment is to find a product that is in a niche market that doesn’t exist from the large mills. You’ve got to cut special custom sizes. Beams, custom cuts, or value added cuts. You can’t compete with the large mills cutting 1x4, 2x4, 2x6, etc, within the current low end markets. The only time you can make money within the market your trying to serve is the short period of time the supply doesn’t exist which is usually only for a short season or up to 1 year at the most, and after that rise in demand in the markets always drop out. It’s a long term return, and you’ve got to know the industry well enough to make money in the tough times. My Grandfather always said, if it was easy Pickens Grandmas would be doin it.

Good info. Thanks for sharing.

Enjoy your vacation bud. You’ve earned it. See ya on the next one whenever that is. Cheers

@WilsonForestLands

10 ай бұрын

Thanks Walt.

Hope you enjoyed that vacation! Well deserved.

Low T " man ...get up , stay on the scene man , keep your head up you can do it , hang in there, don't get weaker get stronger....whatever it takes , bud....

@WilsonForestLands

10 ай бұрын

Maybe you didn’t watch the whole video? That comment doesn’t really apply to what I have going on.

I weighed out buy a mill but found its easier to take my logs to have them milled, I just get a bunch together and run them over when I get low, hell he even unloads them and loads them up on my trailer plus he gets rid of the junk :)

I have had a similarly configured sawmill for about 2 years now. I own it with my son-in-law. I would never have expected to make enough money to be worth the work with a sawmill that small and especially selling softwood. I'm not saying it can't be done but these small manual mills are an enormous amount of work for one person. I have a tractor with forks and even then it is a lot of hard, time consuming labor. Now, if you had a source of high dollar hardwood and ready buyers at hand that's a different story. Having said that, my similar sawmill has paid for itself with the lumber we have cut and used for various building projects (not including the cost of our labor and time!). I think this is about the only way these small mills make sense and even then only if you enjoy the milling. We both do. Neither of us wants to do it every day but we enjoy the logging and milling and using our own resources. So if you enjoy the work and need a fair amount of lumber for your own use I think these small manual mills are great.

midwest area- dried and sized d.f.4x 4 's apx. 1.90 b.ft. any help ? ( no clue on log value)

Do what's right for you in the now. I watch milling vids for enjoyment - have an LX25 purely for personal use, going to be building a log cabin, so not driven by seeing it produce $$ - pure hobbyist. Will look forward to vids on the coastal property, should those come to be - I'm betting the project will be a cabin...but that might be personal bias! Fair winds and following seas!

@WilsonForestLands

10 ай бұрын

That was more of my idea when I bought the mill. To use it for enjoyment and not so much focusing on profit. Instead of using it to process the massive amount of what I need to take off the place, I may get back to using it more for its original intended purpose.

If I owned a Mill for my own personal use, I would make fireplace mantles and table tops. They fetch thousands depending on the slab quality. We are getting one at the Farm, but that Mill will be busy with building projects.

I had a large Poplar hit by lighting. The logs were too nice to think about making into firewood. Invested in an Alaskan Sawmill to give it a try. Made some nice 1 1/4” x 24” x 12’ live edge slabs out of one log. I was going to use it for myself somewhere. Just sold 8 of them for $2800. I cut the next log as 2” x 24” x 12’ live edge. I has me thinking about a mill and selectively processing from my 44 acres of mixed hardwood forest in Southern Maryland.

I agree. If you can find a big cedar, pecan, or something like that that has a pretty grain that somebody would want to use for a dining room table or custom furniture. That's probably hard to find up in the mountains where you are.

I've been very interested in started my own hobby sawmill. As somebody who has worked in the mill industry for 3 years, one this I've noticed is that specialty products makes a lot of money. I work at a fencing mill, and that market is going way way down. we Mill cedar and fir, the fir is treated with mycostat and some is stained. My buddy works at a reman mill that makes tongue and groove and such products, they even use some of our products and turn them into a higher quality higher value product. Making a substantial amount of profit from buying and repurposing lumber, pretty high recovery

The real money in one of these mills is making your own custom lumber to build your own home. The possibilities are endless as far as the type of home. Stick, log, or whatever fits your fancy in between. Wood mizer has a huge presence at the outdoor shows and that gets passed onto the consumer just like stihl chainsaws. If your initial cost is high it takes you longer to recover that cost. Be your own guide but that is my two cents worth.

@Jesusistheonlyway549

Ай бұрын

We are planing on building our barns and our house. The cost of lumber where I live is insane. We also do woodworking cnc and laser work so we can use as much wood as we can get.

I decided I needed a saw mill because we live in an old northern california black walnut orchard. And I was right! Juglans Hindsii is the cats meow of walnuts. I've slabbed 3 so far, around 20" dia. and I'm getting ready cut another tree, 11ft straight, 20" dia. And I have pine and black oak to mill if I want to.

So we moved from Northern Maine where I had access to all kinds of lumber to the Matsu Valley in Alaska…and it’s tough sourcing wood for the mill here…beetle kill spruce…going on 4 years now garbage…or birch..if you can find one thicker than 12 inches your lucky…cottonwood some very big ones 30-36 inches…but only good for trim..interior stuff….very tough….LT40 WIDE…figure I could sell it…but not ready yet.

I remember framing houses with KD milled Doug Fir 2x4"s back in the 70s out here in MA and it was so much better and stronger than the spruce. I also remember when everyone and their brother had a little mill on the back 40. Not anymore. Why? There is no money in it. I recently had some big estern white pine trees cut down that were too close to the house and too big for my mill. The forester said he would grind and mulch them. Right now the tall heavy pines are blowing down due to tons of rain and high winds. I will need to skid them over to the mill and cut them into 8-12" boards for projects as time allows. Take a break, hang tough and saw when you start to miss it.

@kurtdowny I use a good oil based paint, put them out of the weather and sun. It takes a couple of years. But it's most worth it. If you can keep it above 45 degrees, even better. No warpage, or rotting.

I have one but I got it knowing it would never make me money. Purely a hobby for me.

@WilsonForestLands

6 ай бұрын

That was my original intent when I bought mine. I am glad to be back to doing just that.

@ronbell7920

5 ай бұрын

That's the spirit!

I'm sure there are others here, like me, that are more into the forestry side than the milling anyways. If it is interesting, we'll watch 🙂

@WilsonForestLands

10 ай бұрын

That is good to know because that’s the part I am most interested in too. My heart is more in the managing the forest side more than the being a lumber salesman side.

So much fantastic information in this video. Living in western washington I find it funny that 35k for 5 acres is too much out that way when you'd be lucky to get 1/4 acre for $35 khere😅

Thanks for the straight shooting

Are you able to mill larger/longer speciality timbers and beams that the standard lumbers mills can't provide? 8x8s etc. What's the timber framing market like out in the PNW?

@WilsonForestLands

10 ай бұрын

Yes bigger timbers would be better on the sales side. But the trees I need to take out to manage the forest are the smaller ones that tend to be not very straight. If I was taking a out the bigger healthier trees it would make sense to do bigger timbers.

@josephpostma1787

10 ай бұрын

Is it feasible to cut those large not so common timbers and season them for 2 years and hope you find a customer? Or can you mill them on demand as green timber?

@WilsonForestLands

10 ай бұрын

I wouldn’t want to store them for 2 years to dry. I just have a small number of a few different sizes and sell them green. If a certain size isn’t selling I stop milling them until someone requests more.

@Yettiattack

10 ай бұрын

@@josephpostma1787you want to mill green, you can mill dry but its not advised for several factors.

@friendlylocal3731

7 ай бұрын

The problem with Douglas fir beams is that they can start to look pretty rough when they're on a pile for a long time - twists, checks, and other defects that I imagine must make them unappealing to customers. Is this what you've found? @@WilsonForestLands

In my area you can buy treated from box store as cheap or cheaper than the local saw mills

Makes sense to me. Most of the things I like to do I don't want to do full time lol

...i'm still logged in ...the post beam construction was depressing a little the explaination for one big place staying with pressure treated wood post into dirt as better than the two options described there as a concrete pad with a steel insert to bolt the bottom of the beam sitting on it was flimbsy in wind laterally , while the beam into concrete rotted worse supposedly somehow the thing is they always rot just above ground or concrete connection because the water condenses and evaporates more there so a steel post into the ground with some non permeable heavy acrylic maybe inside the steel sleeve which extends maybe atleast a a foot and half 2 feet above ground still sleeved , i saw a parking lot post the same day and realized that would last longer than other posts , i went with cinderblock post supports on concrete footer with 10 foot rebars and high strength fill filled to top of beam seems more traditional except the grout substitution due to cost....../ranting still maybe theres a beam post to below frostline tinker in there with a goal of no ground or at ground rot could use hdpe filled galvanized steel maybe ..../ too much to explain ....

The abundance of Doug fir is geographic! So to keep your mill running it would seem you need to do 1 of 2 things: either transport it to a location where it is in demand or develop a finished product using Doug fir that you can retail using online commerce

I don't want one for profit, I just want to cut & mill the timber on my property for myself to use... I'm not interested in making money with it...

I have a small 24" sawmill that I use as a hobby only. It's cheap, and does me just fine as long as I can get the lumber for projects. But I do understand you.

I have several Doug Fir trees down at my place and a neighbor with a nice sawmill. $50 an hour to cut me up a bunch of lumber that I don't know what to use it for yet. I do need another woodshed but just a small 8 x 16. I only burn it when in my garage. Just don't want to make them logs into firewood. My other shed has been full for several years now. I could buy a lot lumber at Grey Lumber in Tacoma Washington for that kind of $. He has stopped over a few times to see if I'm ready. Will see if I want to stack and dry some more boards. I did that years ago and built a nice 32 x 60 shop 16 ft walls on 2 ft stem wall. That worked out well. Inspector didn't see in my plans the county approved in small print said #2 doug fir or ruff sawn lumber. LOL I showed him that and he signed off for framing inspection. Remember that when you get your plans approved at the county building.

Don't blame you to take a break. At least you can still mill if you have to. Plus you could mill for other people.

@WilsonForestLands

10 ай бұрын

Yep it’s good to have options.

@joeyrector1015

10 ай бұрын

@@WilsonForestLands right. That's the good thing

Good idea, smart to take a break from milling. Thanks for sharing.👍TCT

@WilsonForestLands

10 ай бұрын

The good thing about taking a break is, it will probably make it more enjoyable when conditions improve and I do start doing some milling. Thanks for the comment.

I made my own ash boards for my kitchenfloor. From standing tree to finished tongue and groove boards. I estimate that it cost about 30$ a square foot at 25$ hr. Full length boards all different width makes a very beautiful floor but nobody in there right mind would pay 30 pr foot for a floor. I have black walnut, cedar, hackberry, hard maple and lots of ash. Havent sold 30 dollars worth.

@WilsonForestLands

7 ай бұрын

I think that’s the way a lot of do it yourself projects end up. Expensive if we calculate the time. I imagine you appreciate your floor more though doing it yourself. I have some projects coming up that I will be cutting my own lumber for. it would probably make more sense to buy the lumber but there’s something about doing it yourself.

@stumpfarm3714

4 ай бұрын

Sure your ash floor looks great. I’m doing a rustic cherry floor this summer with small production mill product - kiln dried 3/4” 4” TG matched ends for $2.14 a SF. I don’t know how anybody could match that price with their hobby sawmill. They are asking more than $2.50 per board foot for rough sawn green cherry.

I have a timberking 1220 and love it. Diesel powered.

This is hilarious, great post.

Where I live is in the SE part of Ohio, which is covered with forest. Everyone has wood. I have very mature hickory and oak and I have way more firewood that I could ever use. I used to sell to campers because this is a tourist area. There must be 200 people selling firewood within 10 miles of me. I am 45 miles from Columbus and wood sells at a reasonable prices there but transportation eats up my profit. I can't give it away here. I know how you feel.

Any video you do will be great !!! ps have fun on vacation

@WilsonForestLands

10 ай бұрын

Thank you Steve.

I also have a manual mill, but do not try to make a living with it. I am a woodworker, and my thought was to supply my own addiction. Here in Kansas we have walnut, ash, elm, cottonwood, and a few other species worth cutting, but mostly I just wanted to avoid paying 8$ a board foot for walnut. Before I bought a mill had some guys mill for me, and they just wanted to rip me off, and instead of using the 4/4 scale, and just sawed it on the inch scale, and much of the wood would not clean up at 3/4. Got frustrated and bought a Cooks MP32.

random thought but i saw a vid on here yt , it looked like in florida maybe anyway the man drills a shallow non-potable iirc well using a pressure-washer and pvc in 10' and i think one larger sleeve maybe , the thing about a well is if it's deep or tests good it's drinkable but a solar powered electric motor can be used , i fooled myself because i watched a vid here from somewhere in south east asia where a phd american man from north carolina designed their 4 or 5 barrel water filter using sand, gravel , window sceen , plastic barrel drums , pvc and charcoal could work for a rain filter but it need hieght to use a pump free ball valve or else it's same set up as a well but big hassle ...soundboarding i realized maybe the non potable water from well goes to that filter too maybe but anyway you could hose down your property for free with solar and one of those , i've been designing gutter system to go below a porch and carport roof , between the two roofs and most to rain storage as described for maybe washer machine and toilet for example ....i have other ideas but they get vultured and it's another self only forest gump d%d% ...oh the thing about my gutter makes sense is the independant roff have higher pitch than the house to act as wind fairings and better adjust from no roof or shade or full roof and maybe a greenhouse too for wintertime...../ranting take care hope you're safe ,

I bought a manual bandsaw mill a few years ago for 4k that was a demonstration unit. Thought I could earn some $$ and have some for my own use. The only thing I was able to sell was some live edge black walnut and even that went pretty cheap. Lot of people had the same idea as I did and mills are a lot more common now. Since it wasn’t that big of an investment I will keep it for my own use but as using to generate cash forget about that.

@markyax1467

2 ай бұрын

Everyone wants kiln dried and not ready to invest in that

I retired in 2020 from the military and built my own to prove I could do it. I learned a ton doing it and had a blast. I figured out very quickly that it just wasn’t worth my time, my truck and my back hustling to get logs. I switched to machining and never regretted it. Too many guys in it and too many people trying to get the same logs I was.

@phalanyx3478

2 ай бұрын

What kind of machining? Custom fab/repair or high volume production? Self employed?

Start timber framing! You could pre cut 'kits' for the dumb stuff people put together in their backyard, pole barns, carports etc. Here in the southeast I would love some nice big straight doug fir.

@WilsonForestLands

9 ай бұрын

It’s a good suggestion. My interest is more in managing my land and timber than it is manufacturing products. That’s the main reason I haven’t got into doing things like that. But I may, it might be a good idea.

Isn't pine preferable for interior trim work such as moldings, door jambs, cabinets, and shelving?

@maplebones

7 ай бұрын

There are many types of pine. Some are better than others but clear white pine is what I would choose.

I wish I had a Woodmizer. It probably wouldn't pay for itself. I have a lot of walnut that I could saw up. White pine too. I could find other nice hardwoods to slice up too.

@WilsonForestLands

10 ай бұрын

Mine easily paid for itself but that was when the price of the type of lumber we have here shot up. If you have walnut and other nice hardwoods, that’s a different story. I think that kind of wood is a lot more valuable than what we have out here. When you have that kind of high dollar wood, it may be completely different economics than what we have out here.

In the Midwest we'd buy all the fir and ponderosa you could mill

@WilsonForestLands

9 ай бұрын

If I had an economical way to ship it I would be happy to send you some.

Not sure how well you build but why not make sheds, shelters, pens, etc. ? What about Hip Camps? Camp grounds? People are looking for ways out of the cities for various lengths of time.

Lost all my doug fir trees to a fire last year so I’m buying a mill to make use of the charred but still valuable standing dead wood. It’s ironic because i wanted to sell the logs to a mill but the land is too difficult to make the deal come out cash positive. So I’m better off milling and using the timber for my own projects which will pay for the mill many times over.

If you want to get into milling lumber for just the satisfaction, build your own mill, don't buy one. Money can't buy happiness. You have to make that for yourself. Ultimately it is your choice in what will and won't satisfy you.

You could mill thicker fence boards and thicker 2x4's for higher quality fence materials.

after all us small farmers went out of business local family owned mill 3 miles from my place tried to keep it going with contract to make pallets local budweiser botting company but even with that they could'nt afford employee's anymore everything ended up big auction sale the next nearest sawmill is 2 counties away from me and home depot is 24 miles shit ton of traffic road construction detours to get there all my project on hold right now 😖

What did the mill cost?

Enjoy your vacation 🎉

@WilsonForestLands

10 ай бұрын

Thank you Ron.

Great video

You need to see the price of lumber in the UK, infact I cannot buy the lumber I need except from one timber yard 10" x 1" planned all round Ive convered it for you $7 a foot. £21 per metre which is 39.25 inches. I wanted it for beehive boxes I can buy them cheaper all cut to size.

@Jesusistheonlyway549

Ай бұрын

It’s the same in Ireland. I’m going to get one of these small mills to mill my own lumber. We are trying to build a barns and a house, plus we’re starting a woodworking business. I figure it would be cheaper this way.

@madeingreatbritainchannel

Ай бұрын

@@Jesusistheonlyway549 When you buy in bulk the price is a lot less 40% less

We're in the same "boat" so to speak in Linn County with the heat/fire danger. I however can't stop, because I'm still recovering the windthrows from this past winter. Another small advantage is the low fire danger of work on the "electric tree farm." Using the battery-powered equipment is safer/cooler to run during these conditions. (I'll stop there, so as not to excite the battery-powered equipment haters.) Enjoy the time off, I'm envious. Cheers from your neighbour to the North.

@mandy2tomtube

10 ай бұрын

If the electric Grid goes down and there’s no gasoline to buy. solar and battery power is the only thing that will work, that sense of off grid, back up alone, justifies, electric tools, and vehicles personally, I find I need a lot of batteries, but I don’t miss the smell and the sound

@lpeterman

10 ай бұрын

@@mandy2tomtube You hit it in One.

@WilsonForestLands

10 ай бұрын

Regardless of what the battery powered haters think, the fire danger situation is a legitimate advantage to battery powered equipment. Considering at some point we won’t even be allowed to use the gas powered equipment when fire danger gets too high.

I recently bought a mill . It's been a ton of work . Probably cheaper to buy the lumber. I had a bunch of trees I cut down for a shop build .

It's like the east with freaking oak. You can't get away from it!!!!

“I’m not running my mill because it’s not profitable. Next week I’m going on vacation and after that I’m going to my other castle.” 😏

....also ...got rid of the trees to mill on the property , looks like a hydraulic fire pellet or some fire brick set up for the sawdust could be used now ..../i saw vid on those on here too....darn/lol...youtube , i get a lot of good links, info on here , i saw that mill twice was the thing and i only have one tree maybe for now i could probably chainsaw mill that much , it's a cedar and cedar is claimed about same bug resistance as pressure treated , therefor it seems easier because other than that they kiln dry the wood for shrink it and that kills any bugs already in the wood if there were any the cedar is much more knotty and brittle than pine seems like the reason for high cost and not much supply near me anyway

New drinking game: take a shot every time he says fir.

I would never waste my time cutting a 2x4. Not even for myself.

Well this is exactly how i feel right now. Mine is pine that had a surprise beetle infestation. Could have got more not milling it.

Any chance you could supplement your income by compressing your saw dust into burnable firewood similar to Presto logs? Not sure what the setup cost would be, but I assume your have a large quantity of saw dust. Just a thought.

@WilsonForestLands

9 ай бұрын

I am such a small operation, I probably only produced the equivalent of a cord of sawdust in the last year. I use it in the garden, I think it’s more valuable there to me. It’s an interesting suggestion and might work for someone who produced a lot more than I do.

@metalrooves3651

6 ай бұрын

NO

I think it depends a lot on what trees you can get to make lumber walnut, cypress, oak , cedar should all be profitable, so many storms are knocking trees down all over, too bad they cannnot be salvaged for wood

Well I almost didn’t click because I thought that’s just click bait lol. But you’re serious and have good reason for it. Maybe it’s time to build a product with the lumber instead of selling it. Like little sheds or something. You know the saying about a pound of steel is worth 50cents but a pound of steel in the form of needles is worth $100.

@WilsonForestLands

10 ай бұрын

It is a good suggestion and I might do a little bit of that. My interest and focus is more on the forest management side so my time to spend on manufacturing is limited. But I may incorporate some of that at some point.

Right on point

@WilsonForestLands

10 ай бұрын

👍

Well, I bought my Woodland Mills band sawmill in 2015 because I have 33 acres of old growth forest, huge eastern white pines in the 18” to 48” diameter, spruce, fir, beech, white cedar, white and yellow birch, apple, butternut, sugar and rock maple etc. I never had a plan to sell the lumber just mill it for my own use, making rustic furniture, but, that didn’t last long once the word got out, so now I do custom sawing only, nothing that can be purchased at the local lumber store or sawmill. It’s a lot more satisfying when it’s for personal use and not commercial. Sounds like you had a plan but the world took a turn for the worse and now your stuck with a mill and forest.

@WilsonForestLands

6 ай бұрын

As I said in the video, my plan was not to sell much if any lumber. But after I got it, the lumber world unexpectedly took a turn for the better and the price of lumber shot up to ridiculous levels. That’s when I decided to start selling some. Now that it’s back to more normal, I can go back to my original plan. Just use the mill a little here and there and sell the logs to the commercial mill. Not stuck with anything.

Also, it many counties you cannot build with ungraded wood. You cannot compete with box stores, and their product is kd and planed. So its very hard to sale. The only thing i have had good luck on is wr cedar. 1” boards at different widths 6-8-10-12 other than that with a manual mill it is just too much physical work and wear and tear. Blades only last for about 2 hours even if they are still sharp. They need to be reground to keep them from breaking and that cost is usually around 20-25 per blade when a new one is around 30.

@walshwoodworks8964

9 ай бұрын

I don’t know anyone who charges more than $10 to sharpen and set a bandmill blade.

@Yettiattack

9 ай бұрын

@@walshwoodworks8964 your area is different than mine.

Wish we had Douglas fir here in the south…

Adapt. Learn markets, refine into products. Bandmils are just a tool, business is about creating markets or finding them. That said the mill industry is particularly tough to deal with because of its feast or famine and fluctuating log costs.

Custom cut. The money is in custom cutting. Like someone that wants trailer decking at 2x6, 2.25x6, 2.5x6 or whatever size they want. . Another aspect is pressure treated wood. Basically all the stuff at stores is hemlock. Or at least out west is. You sell them fir, and they go pay to have it treated. Not something you find at a box store. Especially custom cut, full dimension posts.

Don't worry.. a new bug is on its way in September or October. You should be back in business in no time.

No nothing is more said than a sawmill with no logs. I watch my neighbors woodmizer LT40 go unused for months and it breaks my heart

Dude, nobody with a portable sawmill will ever be able to compete with the big mills on construction limber. Specialty hardwoods are where the money is.

Maybe if you get really bored you could do a video on your logging accessories for getting the logs from point A to point B. Don't make the mistake of selling your mill. 👍🍺

@WilsonForestLands

10 ай бұрын

I do have videos using my logging equipment. But maybe I don’t have one where I just talk about the equipment specifically. Maybe a good idea. Thanks for the suggestion.

@WilsonForestLands

10 ай бұрын

I don’t have any plans to sell the mill. For all I know prices could shoot up again and I might start milling again. And I have some other uses for it.

*In my best Samuel L. Jackson voice*: "SAY DOUG FIR ONE MORE TIME MOTHER...!" 😂

@WilsonForestLands

5 ай бұрын

😂

I'd prefer to buy dimensional lumber but stores don't carry it. That's where small batch mills have an advantage. Plus, cutting up walnut and oak into beams and planks would make it worthwhile, in my opinion.

IN 1976dad bought a 52 inch circle sawmill.He messed with putting a Mack diesel engine on it with an air clutch all summer.We are short of logs around here so we would have hadno competition.Iremember telling dad .if we could clear $30 A DAY,it would be worth me becoming self employed.....ON PAPER,we couldnt have done it more than a couple days in a row...thats not figuring the unknown expenses..Of course,one reason is we were making the cheapest commodity EVER..PALLET lumber..As bad as l am entranced,ive never tried to go whole hog into it...I love to see these marketing wizards producing specialty lumber,THE ONLY WAY to actually make a living.

Add value. Make something from the wood. When not cutting hardwood I used to make custom log home packages.

@WilsonForestLands

9 ай бұрын

I have thought of that. I probably would if I didn’t have too many other things to do. It’s a good suggestion and I may at some point.