*Dear good gentlemen of KZread* you can get in contact with me, support me directly, and find all my socials/store/etc thru my Tazet profile: www.tazet.com/foureyes Let’s get into some Mustang stuff (assuming you watched the whole video)... The Mustang’s current engine was built for boost, but so far I’ve just been trying to squeeze as much NA power out of it as possible, which is kind of silly considering it has a compression ratio of -- We’re going to install the Vortech supercharger mentioned in the video (the head unit’s good for 950 hp) -- While we install that, tune it, race it etc, we’ll build a high compression (12.5) NA motor on the side. When that engine is ready, we’ll do an engine swap and find out what a 3-valve can do when it has similar displacement and compression to a gen-3 coyote engine. -- Then we’ll refresh the low-compression engine and install as much of the turbo kit on the engine as possible while it’s out of the car, then we’ll drop in the turbo engine and full send. -- Somewhere betwixt all this I may try to install a sequential, if it’s not crazy expensive. All that being said, the next video will be about putting the Viper back together, hearing its new cam, tuning it, and racing a BMW V10 and an Audi V10. Should be a good one.

@JonR35

Ай бұрын

Always a great day when you upload!!! Been waiting for a while

@Full_Speed_Ahead

Ай бұрын

Make triple sure you install those lifters facing the right way or you’ll be tearing it back apart. You may know that but never hurts to make sure. Prefix has good stuff. I buy Gen 3 Hemi stuff from them. Should sound pretty sick with the new cam!! That spalling on the cam lobe is a major issue with multiple brands so it’s not isolated to Mopar. I think oil is a major player and OE keeps recommending too light of a viscosity because they want gas mileage and to keep EPA happy. Prefix should get you straight on what viscosity to run. Joe Gibbs driven, Lucas oil, or Penn Grade is about the best 3 out there from personal experience having built several hundred engines and using them. Keep us posted! Love the car ❤

@reddoesthings6225

Ай бұрын

Heya Four_Eyes Im planning to build a Supercharged V6 S197, However i have had problems finding a cam for her, Do you know of any sites that do or would have cams for her? love what you are doing btw always happy to see you post.

@hva4897

Ай бұрын

see you in half a year….

@Wasmachineman

Ай бұрын

Sequential?

"hopefully i'll see you in the next one" *disappears for the next 6 months*

@HorrorUberAlles

Ай бұрын

_He can't keep getting away with it!!_ 😭

@Daredax

Ай бұрын

Coryxkenshin be like

@subyob

Ай бұрын

@@Daredax he said he is gonna disappear for 9 months, he is like a pregnant woman that never fails to deliver, the 9 months are almost over tho.

@TravisFabel

Ай бұрын

This makes sense.. His video popped up in my feed today (its now 4 days old) and I realized I didnt see a vid about this viper in awhile...but I didnt see what video I missed.

@Bluebuthappy182

Ай бұрын

Takes time to do this kind of stuff. Kind of reminds me when Kraftwerk were asked once when is the new album coming out. The reply was, We're still building the instruments.

FINALLY A NEW POST 😭🙏

@nono-oz4gv

Ай бұрын

was COPING SEETHING AND BALDING at the fact it takes so long for his videos, they're so well put together makes sense they take so long but THEY TAKE SO LONG edit: bad news: t'was a trailer :( good news: he's not dead

@user-pn5hg8ln5z

Ай бұрын

Get ready every one the g has poster 🫡

@ThePower1037

Ай бұрын

Yay!!!

@dantevito1193

Ай бұрын

It's been 84 years

@tinman7551

Ай бұрын

I came here to say the same thing 😂.

Man I never knew vipers were THIS fast, 20 years old and still beating new cars with minimal mods and relative ease. Amazing.

@harrison00xXx

Ай бұрын

Stock they are not, especially corners are a mess, as with most american cars with V8 or more. I dont know a V8 except from a old 69 Mustang GT, but i was driving a lot with V6 Diesel, regular 1,9 and 2l R4 diesels, as well a NA 1,4l and 2l as well turbo 1,6l and 2,4l petrol. The cars which were the most fun and "fastest" (in general, including corners and driving "agile") were the ones with small/light engines as well a light build in general with a good weight distribution as well low point of gravity. Neither light engines, nor a good weight distribution the average american muscle car give you, including the otherwise pretty iconic and nice Viper. My favorite cars i drive are either my old, turbocharged Renault Clio RS with all wheel drive, drives like a charme also normally, is somewhat "fuel efficient" and goes like hell if i want to. Has just 970kg dry weight and is one of the lightest possible cars with AWD. Sadly its a collectors item somewhat and its a "sunny day" and weekend car. Or, which is a nice cruiser with good handling, my Subaru Impreza from 2010. Has "just" the 2l Boxer Diesel as well its pretty "bad" (not the AWD i hoped for) visco clutch for the AWD. But with a 220 HP chiptuning, removed DPF, disabled EGR and a bigger turbo it also goes nice, just the 1500kg hinders it from being a sports car.

@HochstartHarry

Ай бұрын

A whole bunch of talk, but no real information. Ofcourse the stock viper is still fast, especially compared to a 2l diesel boxer.

@ruelitocayamanda8162

Ай бұрын

That's a huge V10 engine. What do you expect? I don't know what is so surprising about it.

@DomSchiavoni

Ай бұрын

Check out those dyno numbers. 500 Tq to the wheels NA. Most cars cant even match that with a blower!

@johnbutler2780

Ай бұрын

Vipers are pretty light as well aren’t they?

I appreciate that you focus on the N/A engine! I love an N/A engine much more than a blower (unpopular opinion, I know). Also, the fact that you walked a GT350 is astounding! The GT350 is my favorite modern Ford to boot and I was so happy to see you get em!

@MrRangersfan123

Ай бұрын

A gt350 weighs like 3700 lbs. I’m sure this viper would walk one bone stock

@BC08

Ай бұрын

2016 Shelby GT350 - 3781 lbs M/T 1/4 mile - 12.4 @ 117.8 1997 Dodge Viper GTS - 3375 lbs M/T 1/4 mile - 12.2 @ 119.3

@MrRangersfan123

Ай бұрын

Yeah not surprised at at all that 400lbs of weight makes a differnce and especially considering the shelby only really makes good power above 4k rpm

@AnnatarCarvour

Ай бұрын

​@@BC08the GT350 (R).went 12.1 needs to run it Have been bone stock on a tire cobras like mine crack well into 11s but thats boosted 😆

@BC08

Ай бұрын

@@AnnatarCarvour Just used a common resource for both. Motor Trend. Stock GT350s have gone 11s, but so have Gen 2 Viper GTSs.

WAKE UP BABE, NEW MASTERPIECE DROPPED 🗣️🗣️🗣️

@mmllmmll22

Ай бұрын

I'm waiting for masterpiece called "cammed mustang idling for 10hr"

@user-tb5lc5ps6q

Ай бұрын

6 minutes os not a real video tho

@kyleanderson3775

Ай бұрын

It's a 5 minute video about troubleshooting and a little driving. Hardly a masterpiece but whatever floats your boat.

U dont know how much people are waiting for ur videos…. Bcz they are fucking special

@thunderymelons7081

Ай бұрын

the people or the vids

@Cptkiller2010

Ай бұрын

​@@thunderymelons7081Both

@s.prabhdeepsingh

Ай бұрын

@@thunderymelons7081 the vids bro…😂

@chasemer6

Ай бұрын

this is easily the most underrated car channels on KZread.

@toddthezondalover645

Ай бұрын

​@@thunderymelons7081Funny shit

The Viper is such a wildly distinct piece of engineering. For me it's the only American muscle car that truly, wholly supersedes the inbuilt tropes and expectations associated with it's class and manufacturer. In fact it transcends classification as a whole. It did not have a "style", nor a competitor, nor a target audience, per se. It reminds me a lot of the Lexus LFA in that regard, and a few others (that glorious V10!). It is, by design, the purest, most outlandish work of art that its creators could muster. We need more cars like this.

@patrickderp1044

Ай бұрын

yeah when he took the head off i just said to myself "what a beautiful work of art"

@billdang3953

Ай бұрын

Somewhat in the spirit of the over the top classic late 60's muscle cars or late 50's "Super Stock" cars (which boasted big solid lifter cams in Circa 400 cubic inch engines and high gear ratio rear ends).

@TecnamTwin

Ай бұрын

Except the LFA was so expensive and so pointless that some new ones never sold. Nissan GTR overshadowed it at launch. 😁

This man needs a round of applause. Goes out and gets his dream car, breaks it, and actually takes it apart himself. Love seeing people work on their cars 🔥

@nean9894

Ай бұрын

It brings a tear to the eye to see an american idol be found by someone who gives it the love it deserves

@ocdgarage

Ай бұрын

@@nean9894 It sure does!

@chrisS19019

Ай бұрын

I thought your comment said applesauce

@ocdgarage

Ай бұрын

@@chrisS19019 😭😂

This is the quite literally the most underrated channel on KZread. I’m not trying to glaze but you make the best videos as far as quality and informative.

@subyob

Ай бұрын

GLAZING ALERT

@americanosbadassius9292

Ай бұрын

Agreed! Best DIY vids on 3 valve Mustangs I've seen!

@hesliterallyme.

Ай бұрын

@@subyob your parents had you for tax benefits

@smlbder352

Ай бұрын

there's nothing homosexual about giving a compliment or being passionate about giving your thoughts, the people who say this 'glazing' are bottom-feeders who will live with their parents into their 30s and can't hold jobs and usually aren't even African-Americans

@josheakins5137

Ай бұрын

You don't understand what literally means or subjective

Can't wait to see how the maxxed 4.6 responds to the procharger... That car is something special!

@AstroJoe-ts7qd

Ай бұрын

Is the maxxed version going to happen?

@joelarocco5679

Ай бұрын

@@AstroJoe-ts7qdhe needs to milk it for 4 more years first

@caydendavis885

18 күн бұрын

​@@joelarocco5679😂

This channel is filled with great projects! I can't wait for them to come out. Keep up with these cool ass projects

To this day, still a beautiful design...one could argue a work of art. Almost makes up for the PT Cruiser. 🤭

@rcnelson

Ай бұрын

Hey! The Cruiser was a great modern iteration of the old street rods. Maybe it was impractical but so are the Viper, Mustang, etc. Wish I had a Cruiser.

@cpainter56

20 күн бұрын

@@rcnelsonno

Living in Australia, a Viper is financially out of reach, and having loved these since I saw the prototype in a magazine as a 9 year old way back in ‘89, it makes me so happy to see these still getting the love to this day. Mustang project is excellent as well.

@wigletron2846

Ай бұрын

They're financially out of reach here too lol. Its sad because about a decade ago you could get a decent 2nd gen Viper for $25k.

@toddthezondalover645

Ай бұрын

​@@wigletron2846Decent ones have always been over $40k

@benlangley1763

Ай бұрын

My favourite is the 1st gen and like you, I I've been in love since I saw them in magazines as a kid (although I am a little younger than you 😉). About a month ago, I saw one in my tiny little country town in NSW. I would've looked like such a weirdo just standing there for 10 mins drooling 🤤. This is the only time I've seen one in real life and it definitely lived up to my childhood dreams.

@GL-xz3xk

27 күн бұрын

@@benlangley1763 I saw a very early red side piped RT/10 in left hand drive in the early 2000s here in Melbourne. Just stopped me dead in my tracks. Amazing design. Still jaw dropping decades on, especially in a sea of Commodores and Falcons. (And yes I am old 😆)

@user-jp9ox9zd2k

19 күн бұрын

Also in Aus and with you mate, but sadly every bloody thing in australia is out of reach in the car world.

Awesome video! Your content editing is on point, not a second wasted, entertaining and informative all the way through

Guys Four Eyes uploaded, it's a good day

Your Viper ROCKS ! At first, I thought it was a bad lifter, but seeing the way the cam is scored changes the story. I would send an oil sample to Blackstone Labs for a comprehensive oil analysis, that might reveal the cause of this issue. Good luck !

@allanpolk2681

29 күн бұрын

I was thinking the same thing. A possible oiling deficiency, but why only on one lob of the cam. Possibly a clogged oil galley. Or... wild speculation; possibly a bad metal compound on that one lob. Glad he found the cause and provided the remedy.

Awesome quality and a easy watch as always! I dont mind these shorter update videos at all, fills in the blanks between the juicy content :D

As a retired aerospace engineer that did mostly mechanical engineering, the frosting on the lifter's roller and the damage to that cam load suggests three possible (either individual or a combination of): (1) lubrication; (2) metallurgical; and (3) dimensional. Looking at the spalling on the cam lobe and more specifically - where in the roller path (at the ends) suggests the load (side-to-side) profile and that roller's "crown drop" was not optimal. If the surface treatment (nitriding, carburization, ??) on that cam lobe was less thane designed, the surface would fatigue earlier. And a lubricant (tribology) generated fault could also be the cause or a contributing factor. en.wikipedia.org/wiki/Tribology

@ckratzet5286

Ай бұрын

Spot on. Cams were flame hardened DI. Not too precisice as to how hard and where compared to induction. Same on Hemis.

@kylelawson91

Ай бұрын

would it be easy to just say check the oil for metal and check the lifter for spacing.

@IRON_D

Ай бұрын

So you saying a poorly manufactured campaign shaft or this guy used cheap oil? 😂

@livewire2759

Ай бұрын

@@IRON_D No... he said it's most likely the crown on the roller of the lifter wasn't machined quite perfectly... or possibly metallurgy/treatment of the cam (a "soft" spot in that lobe), or the cam lobe wasn't machined perfectly, or that lobe wasn't getting adequate oiling... or a combination of any or all of those factors. The Viper is a supercar, but it's still a mass produced supercar, vulnerable to tolerance stacking just like any other mass produced car. This is why cars have warranties...

@jayk7781

Ай бұрын

Came here for this kind of a response. Thank you very much.

Seeing your GTS on Donut was honestly the coolest thing a carguy like myself could see. As soon as I saw the video and that distinctive color I knew it was your car too lol Every single time I see you post something I watch it. Absolutely love the vids!!!

@Four_Eyes

Ай бұрын

thanks brother 🙏

As a child. This was my dream car. I remember seeing one at a gas station randomly, and the guy must’ve seen my staring at it in awe. Long story short, he let me sit inside it. 20ish or so years later and I still remember that.

Man I really enjoy the videos and information about each car! Keep up the good work man!👍

I don't think I have seen a video ever that gets to the point and doesn't drag on. Very nice work. Looking forward to the results.

@Four_Eyes

Ай бұрын

🙏🙏

Best channel there is. unique builds really well filmed and edited. As well as very informative and entertaining. Please never stop making these.

I love seeing you post about the Viper! I've been hooked ever since you got it!

Man I CANNOT wait for these next two car upgrades. I love both those series so much

Saw this suggested and as a classic viper fan had to watch. Subbed. Looking forward to more!

I wait for these videos to come out, I absolutely love your content man, keep it up!

Please post more often, you have lots of subscribers… take advantage of it! 😢

@conner768

Ай бұрын

it’s harder for small creators cause they usually have full time jobs plus putting out the types of videos he typically does usually involve spending a decent amount of money on parts to upgrade a car then go test it. i do agree though i really enjoy his content, even if the videos don’t involve a bunch of expensive modifications or super time consuming work being done on the car id enjoy seeing more upload’s about small updates with the cars or racing/ driving.

@dailydrivenclassics46

Ай бұрын

@@conner768lol not expensive you say? He built a 3v NA and if I had to guesstimate he dumped over 20 k into the mustang alone also with all the different revisions he does of each stage, it is super time intensive. And he is no small creator at 220k subs he could easily make 10 k a month just with his audience and replace his normal job.

@retrograde11

Ай бұрын

Quality over quantity....

@davidmeloyaan2635

Ай бұрын

@@retrograde11 sure, but I don’t think you should post every 3 months for a 5 minute vid. I love the channel and would love to see more that’s all I’m saying

@ryland69420

Ай бұрын

You think this shit is cheap bro? lol… please sink tens of thousands more dollars into custom racing gear so I can see, please!!!😂

In my opinion it was probably floating that valve (weakened spring) and hammering the cam. Or possibly slightly sticking valve in the guide doing the same thing.

One vid every few months, I’m fine with it because they’re so darn good. Reminds me of the days KZreadrs posted because they wanted to and not for ad rev. Cheers bro

One Four Eyes video a day keeps your Rock Knock away ❤️

Such great cars! Awesome video man, love the journey with the Viper!

great video , short , sweet and to the point ! keep up the great work

My neighbor had a Viper when I was in high school. White with blue racing stripes. Looked so sick

My only gripe of your video is just that it's not long enough! Always delighted to watch your new videos though!

I don t killing myself about cars and stuff,but man,your skills are above and love to see supercars well maintained.Of course subscribed

man your videos are literally S tier, please don't stop making them

HE FINALLY POSTED! KZread trolled and didnt send me the notification, but i came here 1 day after and luckly the video was there!

Thank you for the new upload❤

Thanks for the vid, you're good at making them and best of luck with your viper build! If it's not too much trouble I would pull the oil pan off and look at the main and rod bearings, that sound was very rod-slappy to me.

This channel is criminally under subscribed. Amazing editing, fantastic content with great presentation. What more could you ask for, besides frequency ? Absolutely love the video. Can’t wait for the next. 🥰😍❤️

He aint resting the mustang until its gonna be a demon destroyer 🗣️🗣️🔥🔥🥶🥶

@petesmith5092

Ай бұрын

THAT may never happen though...

I love this car so much. Great episode.

Finally man, as much as I love the stang vids, I was hoping to see the vioer get some well needed attention and love. I love v8’s a lot but something about a v10 that has the American v8 feels and sounds is just amazing.

I wish I could hemorrhage money on my cars!

You bought a Dodge ... sorry for your luck, but you should know better ...

@ScottAT

Ай бұрын

Sad but true.

@JHKCF

Ай бұрын

Viper engines are usually pretty bulletproof.

@SuperYouTroll288

Ай бұрын

@@JHKCF That must be the reason why I've seen so many that are hurt ...

@riogrande163

23 күн бұрын

Found the lsx fanboy. Yikes. Brand loyalty sheep are so pathetic.

@SuperYouTroll288

23 күн бұрын

@riogrande163 Says a troll that knows absolutely nothing about performance and reliability ... GM sucks too, but out of Ford, GM and Dodge, GM has the best gas engines ... always did.

this is one of my favourite builds ever, DON'T DISAPPEAR AGAIN

nice to see the Viper get some love.

Awesome video dude, always loved the viper. Almost bought a salvage one a few times. Also the 2017 acr is probably my favorite car of all time.

I don't think there's anything more exciting to see another new 4eyes new post 😭

That just sounds MEAN!! Love that exhaust note.

I’m astonished that the Viper walked the new Mustang. That’s one bad ass snake I love that car. The right year, right color, right wheels and no stripes. 👍🏼

The Viper was my Dream Car when I was a kid, it is awesome to see how well it holds up even 20+ years later

the viper was my dream car growing up, I used it in every video game it was featured and then I kind of forgot about it. This video made me feel 12 again. Whay a beautiful car.

Our king went hard on the editing in this one.

For a guy with more money than I'll ever see, you sure do have some serious fun with it!

Awesome vid/content! Brings back great memories of my ‘02 snake! 👏🔥👀😎

Great job on the proper disassembly to find the issue. I know what a horrible, time consuming and expensive job that is so kudos to you for doing it right, finding the problem and making it better. Most people would have ignored it until it killed the car.

Beautiful car....sits with such poise..perfect on every level...lucky man to own the piece of motoring history..

V10 Viper...heck yes! I had a chance to drive a GTS in around 2001 on an Autocross track- I was impressed. Amazing amount of torque! Only thing I could find with torque anywhere near is a Buick GS455 with power adders.....You are making me think Viper though...goddang beast!

Never been a huge Viper fan, but my God that color is awesome. With the color and the tinted windows, that's probably the nicest looking Viper I've ever seen :)

"So if you are into dope shit, you know what to do" You bet I do. This is how you make people sub, good freaking job.

@ 1:21 OMEFFIN'G, THAT CAR IS SO EFFIN' BEAUTIFUL!!! That GTS body are just so freaking gorgeous!!! Really, 2nd gen Vipers are absolutely magnificent works of art, and unbelievable marvels of automotive engineering. I can genuinely feel it in my stomach when I see them in person, and very, VERY few cars have that effect on me...

Your GTS is one of, if not my dream supercar, ranking extremely high on my bucket car list. I actually saw the video that Donut made about the different generations of Viper, and I picked yours as my favorite one, way back then...

You can pinpoint vibration/sound location putting a wooden broomstick/dowel on the engine and then place your ear on the rounded end for comfort. My friend showed me that to pin point rod/rocker valve chatter with the valve cover on. Works really well.

Awesome video. Love the Viper!

It really is amazing how little power they made out of such a huge engine

Oh snap! That was some VERY loud ticking. I would have been terrified driving it to the track and back. That cam lobe damage looks really weird, especially considering the roller is fine. Maybe it was just some fatigued metal, or it had some problems during the casting or hardening stage of fabrication. Huh... Well, i hope the tick/slap/rattle is gone after the new cam and heads. Pumped for the next video!!!

Seemed like porosity in the cast process, or maybe just fatigue, good thing you diagnosed it in time!

I think this is my favorite viper gen. Just a nice blend of retro and modern styling. Also idk how I've never heard of this channel. You're making cars I make in forza but irl! lmao

Good video mate. I think U did a good job. I got stick into the engine no worries. U know U stuff. Hang in there

Very nice upgrade to the V10. Glad it was just a lobe and lifter.

Nice and concise, good work

Love the look of your viper! Great colour too, makes a nice change from red! Shame I’m in the UK, would love to go head to head with my Aston Martin DB9!👍🤣

Sick car, love all the N/A work!

@Four_Eyes

Ай бұрын

🙏

Dude,I had a dream today that you uploaded a new video,was so real that I went check

love to watch, cant wait to see the mustang !

Great content !! No super click bait whatsoever ! And that v10 was made to last forever.

Awesome! Very nice and straightforward video!!

Really awesome vid mate. You rock bro. Well done.

@Four_Eyes

Ай бұрын

very kind thank you thank you

The Pedro Chespirito plug from the Simpson's was a nice touch. That had me laughing pretty hard.

Vipers are just so beautiful car, classical icon of that era too.

love your content sir, thank you

im always happy when i see a new video come out man keep it up

That car is drop dead gorgeous!

As you took apart the engine I think it’s funny a viper shares some of the same lifter and push rods as my 98 dodge Dakota lol

its nice to see a sports car still being used like a sports car 🥰

The Viper is a classic. Beautiful Car.

Modern Viper content is what we all need right now.

😢 finally a new video but I can't never get enough of them please me them longer 😢

Loving the videos. Just waiting for that mustang build to be completed.

The vipers still look f-ing awesome! Most old sport cars are slow compared to modern cars, but the viper is still out there killing it. They will always be in my top 5 list I envy you, i wish i had that viper.

That Viper!!! Love to see it!!

The Viper still looks damn good today :)

Looking forward to the next upload ..

Awesome video man. And car! New subscriber ✌🏻

I remember a magazine talking about this before it was released. A new Shelby monster... but the side pipes were showing and it looked like a beast. Wish they left them uncovered. Always looks like a pretty girl that's covering her charms...

I honestly didn’t know your viper was the one on donut, but I’m super happy it was.

That Milwaukee ratchet is such a great tool, it made me buy a 12V Milwaukee tool even though all my other power tools are 18V Makita. I'm sort of committing battery adultery, but damn that compact 12V battery is convenient. Fits into tight spaces. That thing has saved me lots of aggravation, a very useful tool, one of the best things I've ever bought.