super explanation and talk about load cell and encoders

@realpars

5 жыл бұрын

Thank you Ganesh!

Your videos are of very high quality.

@realpars

2 жыл бұрын

I appreciate that!

Verry interesting, thanks!

@realpars

5 жыл бұрын

Happy learning!

thank you for your great work

@realpars

2 жыл бұрын

Our pleasure!

Thanks for knowledge sharing

@realpars

5 жыл бұрын

You are very welcome!

Great thanks

@realpars

4 жыл бұрын

Thanks for your support!

excellant video...

@realpars

5 жыл бұрын

Thankyou!

I’m glad to subscribe to ur channel

Good explanation

@realpars

10 ай бұрын

Thank you very much!

Merci, cette vidéo est très utile.

@realpars

6 ай бұрын

You're very welcome!

Very informative. How do belt and ball-screw rails compare from durability perspective?

@realpars

2 жыл бұрын

That really depends on the service and the size of load being moved. Typically, belt-driven systems will require maintenance more often than ball-screw drives. Belts tend to stretch an deform if not tensioned properly or aligned properly. Ball-screw drives are very durable, but maintaining good lubrication is very important. Generally, ball-screw systems can transport heavier loads than belt systems and can develop higher thrust. Belt drives are much more economical if a load has to be moved a long distance (>3 meters).

Iam interested in this video

And also interface module function in plc please Difference between et200s and et200m(failsafe)

@realpars

5 жыл бұрын

Thanks for the topic suggestion, Aqeel! I will put this on our list!

Please sir can you help me ! I want to input analog signals from potential transformer and current transformer to the analog input of PLC SO what interface do i have to implemt So the output of these two transformers can be measured and plc can read these signals?

@realpars

5 жыл бұрын

First, you need to make sure that the analog input card that you have for the PLC is able to receive the type of signal that you want to connect to it. Then you can read the manual for the sensor and follow the exact wiring diagram to wire the sensor to the PLC input card.

@Ghauri7863

5 жыл бұрын

Suppose that plc can accept analog input but what device do i need to convert A.C secondary current to measureable by PLC?

i still dont understand how the screw is not coming out when spinning. Is there any suggested time stamp?

@realpars

2 жыл бұрын

The screw is fixed at the drive end. When the screw rotates, the load nut moves along the screw shaft. Physical stops at the end of the screw shaft prevent the load from moving off of the end of the shaft.

Please make a video on difference between et 200s and et 200M And

@realpars

5 жыл бұрын

Thanks for the topic suggestion, Aqeel! I will pass this on to our creator team.

@aqx1729

5 жыл бұрын

@@realpars i really need to know about that Thank you

❤❤❤❤❤❤

Genial

@realpars

Жыл бұрын

Thank you very much!

Please make video about PID Regulators logic

@realpars

5 жыл бұрын

I will pass your request on to our team. Happy learning!

also start plc siemens servo programming tutorial

How to increase speed of servo motor to servo drive...

@realpars

4 жыл бұрын

There is a limit to the speed that a servo motor can run. Check the motor nameplate to insure to understand this maximum. Increasing speed above this maximum will require a new motor or a different gear reducer. Many times, there is a maximum speed that is configured in the servo drive. Check for that parameter and see if it can be increased. Often, the maximum speed is set due to limitations in the device being driven. For example, many conveyors cannot be operated faster than a certain speed or they might jump a track or cause excessive vibration.

@Lecky215

4 жыл бұрын

@@realpars thank you sir for your responce and sugestion...

Got here because of michael reeves and I still haven't taken a single engineering class yet thanks(?) youtube