After watching so many of these, I cannot go into a bathroom with Tile and not see some “interesting” things 😂 Another gem of a video brother. Killing it!

@LandbergTileTV

Жыл бұрын

thanks for the kind words! 👊

as always, impeccable work

@LandbergTileTV

Жыл бұрын

thanks!

You make it look easy!

Thank you 4 this review, I've become a better tile installer due 2 your videos which has helped support my family giving us a better life

@LandbergTileTV

Жыл бұрын

Great to hear!

Usted es mejor 😊muchas felicidades

nice work as usual. whats a little strange is grout joints on subways or any basic ceramics these days. as you know grout joints have gotten smaller these days , when i started the basic joint on floor tiles were 1/4 in, then when it went to 3/16 it seemed so very tight, now everything is 1/16 more or less. now take your basic 4- 1/4 , 6x6, or any basic ceramic wall tile/ subway tile, which years ago were always butt. i use to do boat loads of this basic tile and never put a joint in it. those ceramics had a nub built in it to give it like a 32nd of an inch and if they didnt have that you just spaced it very tight, but now ceramic wall tiles are spaced much bigger, you hardly see any ceramics with a butt joint....so all joints have gotten smaller over the years but ceramic joints have gotten bigger...

1/8" Horseshoes in back of niche sill to get your slope... And I thought I was the only one doing that 😂

@franciscoibarra1232

Жыл бұрын

Same here 😂

I stop in the chat to say this every six months or so, but you have the best tile videos on the internet

@ryangunderson5064

Жыл бұрын

Curious though. I saw the 16th inch spacer used to pitch the piece of quart on the sil. You also have the water proofing under the sill pitches too right ?

@LandbergTileTV

Жыл бұрын

Thanks brother, I really appreciate the kind words! 👊

@LandbergTileTV

Жыл бұрын

Yes, the prefab niche is waterproofed

Recommendations for a tile saw? I do only 2 or so bathrooms/year and odd backsplash - usually large format porcelain. Maybe 1" thick fireplace stone too. I know the DeWalt d24000 does it all, but it's huge and around $900 with stand and taxation.

@LandbergTileTV

Жыл бұрын

We are absolutely loving the Kobalt 24v tabletop cordless tile saw along with a simple 24" tile cutter. This setup is small, light and does it all. I have a new video uploading today on that saw.

Question about backboard piece you installed above the niche. Did you screw through Schluter membrane and then waterproof the screw holes before tiling over? Looks amazing 👍🏼. Thank you.

@LandbergTileTV

Жыл бұрын

Yes I did and thank you!

Great work as always, just wondering why there was no waterproofing between the Kerri board and tub?

@LandbergTileTV

Жыл бұрын

We run a bead of silicone as well as Kerdi band.

Omg. What the fuck could I ask for. Wow. Rbeam 300, sprinkled in some oldie but goodie scores. Fuck yah. Thanks so much.

@LandbergTileTV

Жыл бұрын

Tile on brother!

when wet shimming, how long until you begin to put screws into the studs? The next day? seconds after wet shimming?

@franciscoibarra1232

Жыл бұрын

Next day, when the thin set is hard

very tight work... dont you need to cover the kerdi board washers? maybe you were going to do that one on the right side of the niche after placing the sill?

@LandbergTileTV

Жыл бұрын

Yes, we covered them afterwards with band

👊👊👊👌🏾

Go Berg! I see that Kobalt is getting a lot of action! 😅

@LandbergTileTV

Жыл бұрын

lol it's getting used and abused! but holding up like a champ!

@angelhernandez1526

Жыл бұрын

Is it getting harder to slide the tray after every job

@angelhernandez1526

Жыл бұрын

Seems like mine is starting to get stuck

@reddbeard2030

Жыл бұрын

@@angelhernandez1526 Yeah! Berg and I were just discussing that issue. In the instructions it Does Say to keep the rails oiled. FYI: Take the table off the rails. Clean rails and oil up those little ridiculous bearings. Every Time You Finish Using It 😪

Water indeed cant do nothing to that Pica pencil led. 👍

@LandbergTileTV

Жыл бұрын

Nope! 👊