Insightful teachings, Sir. I'm sure you'll make 80k subscribers :) Ever thought you'd be doing this 8 years on? Congrats, and thank you!
@rayfalcone68976 жыл бұрын
very nice video John I really enjoyed........you really know your stuff....great job....I watch them all......I'm also a retired machinist millwright.......79 years young.
@stanleyrodgers337511 жыл бұрын
Thanks, John! I like that follow rest (traveling steady rest). Carriage really does always seem to speed up when close to the end of the thread! Nice tip on setting drive gear clearance.
@vicebi10 жыл бұрын
Happy New Year. I enjoy seeing all your videos. In this I really drew attention, that contrary to what my dad taught me, you tools to thread the counterpoint and not towards the head around. Just wanted to share this with you. Congratulations on your talent and thanks for sharing. A hug from Mexico.
@FredMiller11 жыл бұрын
Nicely done! I picked up that you have a handle on the nut that holds down your tool post. That is a great idea (no wrench needed). Sounds like a project I will be making. Thanks for the tip....
@harleyghost10 жыл бұрын
Very interesting, your lathe is is very nice and well taken care of. Thank you for sharing the craft.
@thehowardnicholson11 жыл бұрын
that's a good trick to set the gears clearance, thanks
@swampratt3611 жыл бұрын
Very skilled machinist you are bravo !
@Mrbenggo11 жыл бұрын
Enjoyed your film John,I will be looking at the rest of 'em.
@BigMjolnir10 жыл бұрын
Don't know what all the fuss is about, seems perfectly understandable to me... Thanks for showing this. That insert with the "depth stop" built in is very clever. I'd not seen one before. I wonder if ball screws could be done similarly, but with a different insert?
@WojciechP91511 жыл бұрын
Didn't know about that paper trick. Good to know
@edgardoprincipe26179 жыл бұрын
muy buen trabajo bien detallado
@KyMJose8 жыл бұрын
Es increible que sin entender el Idioma linguístico....EL IDIOMA MECÁNICO, TÉCNICO...en el video, se llega a comprender mucho. Magnífico!!!!!
@millomweb
3 жыл бұрын
Translates as: It is incredible that without understanding the linguistic language ... THE MECHANICAL, TECHNICAL LANGUAGE ... in the video, you get to understand a lot. Magnificent!!!!!
@LarsBerntzon11 жыл бұрын
Nice video, what material are you using in the acme rod?
@doubleboost11 жыл бұрын
Hi All I know about the material is that it was 316 stainless I was given it so that is what I used EN8 would have been my choice if I was buying it You should give it a go on your myford some fantastic work has been turned out on "old myfords" regards John
@oudijzergek11 жыл бұрын
Hello There, noticed you have a frequency converter on this lathe. Are you aware of the related cooling problems ?. I mean at low speed the cooling fan on the motor gets less efficient while heat production goes up. To avoid that you remove the normal fan and put on a constant running electric cooling fan, you can get those made for the purpose but some ducting and a normal fan will do as well.
@millomweb
3 жыл бұрын
Really depends on how long the motor's running for. You may be thinking in this video the motor is running slow. It is not. Motor is running a reasonably normal speed and lathe gearing is giving the slow spindle RPM - which also means there's very little load on the motor to generate heat.
@Moronicsmurf11 жыл бұрын
Thats an insert tool, wouldnt that wanna go faster so the heat leaves with the chips and dont go into the insert and thus making it expand, catch and break it...
@doubleboost11 жыл бұрын
I would think in a production enviroment it would be run much faster Just playing at home nice and slow is my method John
@brucegor2 жыл бұрын
your accent says you should be calling out in metric?
@jhareng11 жыл бұрын
Could do with that 626 at the moment for the P800, need to raise the vice up 9 1/2" off bed so head clears when swung 90 degrees. Doin me ed in.
@atcaleb11 жыл бұрын
he'll be fine with light cuts like that. I am surprised the machine is rigid enough to run inserts. I am surprised to see that insert too. Light cuts and slow speeds I guess it will last forever. In production the cuts would be much deeper and much faster and yes would have issues at that speed-or so I am told.
@Darryl60311 жыл бұрын
What did you say???
@user-ww7ym8tb4i11 жыл бұрын
Хоть и не по нашему, но вполне грамотно.!
@millomweb
3 жыл бұрын
Translates as: Although not ours, but quite competently.! ???
@doubleboost11 жыл бұрын
Hi It is 316 stainless steel
@millomweb3 жыл бұрын
3:43 Metric conversion - commonly 120 tooth w/127T - you said 100 - are ye sure?
@jhareng11 жыл бұрын
Translation please. Only kidding John.
@millomweb
3 жыл бұрын
I note there isn't a transcript with this video. I wonder if that was the problem :)
@doubleboost11 жыл бұрын
It is made from bronze lol
@stuknda80z11 жыл бұрын
could you up load this in english please. for clarity when i say english I mean the english we here in the states speak,thanks
@millomweb
3 жыл бұрын
LOL ! I wonder if that's why the transcript's not available !
Пікірлер: 34
Insightful teachings, Sir. I'm sure you'll make 80k subscribers :) Ever thought you'd be doing this 8 years on? Congrats, and thank you!
very nice video John I really enjoyed........you really know your stuff....great job....I watch them all......I'm also a retired machinist millwright.......79 years young.
Thanks, John! I like that follow rest (traveling steady rest). Carriage really does always seem to speed up when close to the end of the thread! Nice tip on setting drive gear clearance.
Happy New Year. I enjoy seeing all your videos. In this I really drew attention, that contrary to what my dad taught me, you tools to thread the counterpoint and not towards the head around. Just wanted to share this with you. Congratulations on your talent and thanks for sharing. A hug from Mexico.
Nicely done! I picked up that you have a handle on the nut that holds down your tool post. That is a great idea (no wrench needed). Sounds like a project I will be making. Thanks for the tip....
Very interesting, your lathe is is very nice and well taken care of. Thank you for sharing the craft.
that's a good trick to set the gears clearance, thanks
Very skilled machinist you are bravo !
Enjoyed your film John,I will be looking at the rest of 'em.
Don't know what all the fuss is about, seems perfectly understandable to me... Thanks for showing this. That insert with the "depth stop" built in is very clever. I'd not seen one before. I wonder if ball screws could be done similarly, but with a different insert?
Didn't know about that paper trick. Good to know
muy buen trabajo bien detallado
Es increible que sin entender el Idioma linguístico....EL IDIOMA MECÁNICO, TÉCNICO...en el video, se llega a comprender mucho. Magnífico!!!!!
@millomweb
3 жыл бұрын
Translates as: It is incredible that without understanding the linguistic language ... THE MECHANICAL, TECHNICAL LANGUAGE ... in the video, you get to understand a lot. Magnificent!!!!!
Nice video, what material are you using in the acme rod?
Hi All I know about the material is that it was 316 stainless I was given it so that is what I used EN8 would have been my choice if I was buying it You should give it a go on your myford some fantastic work has been turned out on "old myfords" regards John
Hello There, noticed you have a frequency converter on this lathe. Are you aware of the related cooling problems ?. I mean at low speed the cooling fan on the motor gets less efficient while heat production goes up. To avoid that you remove the normal fan and put on a constant running electric cooling fan, you can get those made for the purpose but some ducting and a normal fan will do as well.
@millomweb
3 жыл бұрын
Really depends on how long the motor's running for. You may be thinking in this video the motor is running slow. It is not. Motor is running a reasonably normal speed and lathe gearing is giving the slow spindle RPM - which also means there's very little load on the motor to generate heat.
Thats an insert tool, wouldnt that wanna go faster so the heat leaves with the chips and dont go into the insert and thus making it expand, catch and break it...
I would think in a production enviroment it would be run much faster Just playing at home nice and slow is my method John
your accent says you should be calling out in metric?
Could do with that 626 at the moment for the P800, need to raise the vice up 9 1/2" off bed so head clears when swung 90 degrees. Doin me ed in.
he'll be fine with light cuts like that. I am surprised the machine is rigid enough to run inserts. I am surprised to see that insert too. Light cuts and slow speeds I guess it will last forever. In production the cuts would be much deeper and much faster and yes would have issues at that speed-or so I am told.
What did you say???
Хоть и не по нашему, но вполне грамотно.!
@millomweb
3 жыл бұрын
Translates as: Although not ours, but quite competently.! ???
Hi It is 316 stainless steel
3:43 Metric conversion - commonly 120 tooth w/127T - you said 100 - are ye sure?
Translation please. Only kidding John.
@millomweb
3 жыл бұрын
I note there isn't a transcript with this video. I wonder if that was the problem :)
It is made from bronze lol
could you up load this in english please. for clarity when i say english I mean the english we here in the states speak,thanks
@millomweb
3 жыл бұрын
LOL ! I wonder if that's why the transcript's not available !