Greetings from southern Indiana, USA. Great video. Thank You for sharing.

Thanks so much for putting this video up. It’s great to have knowledgeable people share their wisdom with us all. I think you may have just helped me identify the flat spot issue I have with the Weber on my Fiat!

@carburettorrebuildservice8964

3 жыл бұрын

I do hope this will help you, i always try to share my experiences with the hope that it would help someone. thank you for the feedback.

Great video, thank you sir.

Love the instant start up

Great info + video, thanks for sharing

Whata difference this video is from others i found searching. Its great to hear someone talk from experience. God bless.

@carburettorrebuildservice8964

3 жыл бұрын

Thank you

I just wish to add my compliments - Great content and advice for us DIY guys. I am busy sorting out a 4.1 for my truck and I have carb problems I think. I might end up sending mine in :-) cheers.

@carburettorrebuildservice8964

Жыл бұрын

I would be happy to help.

Your information fix my problem! Thank you for such great content.

@carburettorrebuildservice8964

2 жыл бұрын

Happy to help!

Invaluable wisdom there. Thanks so much mate

@carburettorrebuildservice8964

11 ай бұрын

Thank you.

Great video

@carburettorrebuildservice8964

8 ай бұрын

thank you.

That little A14 revs very willingly . Brings back fond memories from when i was preparing 2 of them for racing back in the early 90s . I used to own Renault 8s and 10s with the very popular Alconi engines . The dcd 7s were most probably the most tuneable carbs back then and all my Rs had one on . The adverts used to say "Power and economy king " Nowadays i am tinkering with the 38 dgas carbs and your videos on them is just awesome and informative . Thank you for sharing it . I live in SA and i would like to know how i can contact you other than via public comment .

@carburettorrebuildservice8964

3 жыл бұрын

Thank you for the comments, I fitted bike carbs to a Renault 9 engine, this engine was in a little R8, we also had a Gordini head on the engine, it was a little rocket. my number is 0-6-0-6-5-4-6-9-6-6

@freddieverreynne3344

3 жыл бұрын

Hi please if you can help me a have 32/36 weber a install it on vw 1800 bore 2L shim head gasflow branses on when a start it it adels when a try to ref it up slow it straggle to ref up then a ref full frottle it refs up what is the problem Thanks if you can help me

@carburettorrebuildservice8964

3 жыл бұрын

@@freddieverreynne3344 it is difficult to say but it sounds like your main jet is to small, make a video and send it to me via whatsapp 0-6-0-6-5-4-6-9-6-6

Thank you I'm going to try the F-66 on my formula ford 1600 engine to get rid of my flat spot, it's little info like this that really helps. I'll let you know if it helps

@carburettorrebuildservice8964

2 жыл бұрын

thank you, please do

Hey man thanks so much for putting this info up! , ive got a 1981 Datsun sunny b310 wagon, i always wanted to put a 32/36 weber on it but had no idea of the jetting so after watching your vids i bought a second hand weber cleaned and rebuilt it i made a 2 piece adaptor plate and have installed the weber on the car running a A15 motor the weber came with main =130 secondary=130 Airs main 175 secondary 125,idle jets are 55 and 60 and emulsion tubes are f66 with 3.5 and 4.5 venturi/choke i forget what there called lol i figure its close as a base tune it should run the car ok until i can order parts not sure when this will be as im a kiwi and NZ has just gone into another lockdown!. Im having a major issue which i cant seem to diagnose i have checked for vacuum leaks had the carby on and of 3 times now changing to different thicknesses of gaskets even trying RTV and i keep having the same result. The car will start i have to idle real high to keep it going, i get it warm still wont idle so i turn the mixture screw out until it does but it has to be about 6 turns out but the lowest i can get the idle is 1100rpm and this is with the idle screw not even engaged with the arm! Ive looked through the barrel with a torch shining up it has minimal gap much less than the old carb which was set at 800rpm. The car runs very rich and every time ive changed the gasket its exactly the same result! I have checked float height with no problems there the only other thing i havent done is disable the power valve but it has a new plunger so shouldnt have a leak there. Is there any advice you can give me to help get my car running on this carb thanks for any help :)

@carburettorrebuildservice8964

2 жыл бұрын

Hi, what size is the idle jet, it sounds like it is blocked or very small

@chrisjack4310

2 жыл бұрын

@@carburettorrebuildservice8964 its a 50 or ive tried swapping them around with the second barrel which has a 60 makes a little difference to where i have to have the mixture screw but does not effect what rpm it idles at, like i said the part i find weird is i cant keep turning the idle speed screw until the engine dies it will only go down to 1100rpm

@carburettorrebuildservice8964

2 жыл бұрын

Please ensure both butterflies close properly, and ensure you are not leaking air.

@chrisjack4310

2 жыл бұрын

@@carburettorrebuildservice8964 have checked butterflys are fully closing have even gone as far as unscrew them relign etc and still can only see the tiniest bit of light come through which ive checked the standard hitachi and theres more light coming through those butterflys and it was set to about 800rpm, ive disabled the power valve the car seems to run nice otherwise like when you rev it.im about 4 turns out on the mixture so smells abit rich, have lowered the float more just incase, tomorow i may put the standard one back on and make sure it still idles below a 1000rpm to eliminate the possibility of a manifold leak etc , im just abit stumped i really cant figure this out ive even gone as far as to loosen the carb bolts to see if any vacuum leaks apper and the gaskets and rtv are gluing the carb down i could get it to leak if i angled the carb with the bolts very loose so i dont think my adaptor plate is leaking ive sprayed degreser all around the carb and manifold and cant find any issue. Thanks heaps for your help, could it be possible that the throttle shafts are leaking air? They dont feel loose up and down but you can move them slightly in and out

@carburettorrebuildservice8964

2 жыл бұрын

The second barrel’s idle jet should not have any effect on the idling, the idle is only done by the first barrel.

Wat a sound!

awe lekker vid

@carburettorrebuildservice8964

3 ай бұрын

Glad i could help you, thanks for watching.

question to expert i got just open hole on weber where is wenting or purging to the charcoal canister, is that normal? where i can buy pipe right size? thanks

Thank you so much for your video. I am a little curious as to why you sealed up the power valve. You mention that a 1400 doesn't need it and I would like to understand why. Is it the size of the engine? Or something else? Would enjoy hearing your thoughts. Thank you in advance!

@carburettorrebuildservice8964

2 жыл бұрын

Yip, the size of the engine. Must of the Weber mods on 1400's are on standard engines and with the power valve still active it could over fuel. thanks for watching the video's.

Hi! Just came across your videos. Very interesting and helpful. I've just installed a 32/36 on my mk2 transit, 2.0ltr pinto. She runs great, pulls well with very little flat spots. It ticks over fine too, but when I drive through the gears and come to a set of traffic lights or junction, the carb refuses to find idle and the engine cuts out. Any suggestions?

@carburettorrebuildservice8964

2 жыл бұрын

Perhaps try a smaller idle jet, also ensure your float level is correct and the needle and seat seals properly.

1987 Mitsubishi Montero SWB 2.6 with Weber 32/36 DAF - My carb is now fully open at stop. It failed on a restart from driving all day and now fails to adjust idle down. I'm revving at 4000 rpm now when in Park. The top flaps are open and don't close up. The car has been driven all week after not being a daily driver but performed well. Checked all throttle cabling, but the flaps don't close. Is this a broken Electric Choke? or another diaphragm? Thanks in advance.

The f66 make a big difference i ran the f50 f6 and changed both to f66 i get a bit to much fuel with the powervalve i took it out

@carburettorrebuildservice8964

3 жыл бұрын

Die F66 is net baie skaars

@koosdemeyer9105

3 жыл бұрын

@@carburettorrebuildservice8964 hulle is ja ek was velukkig om 2 in n ou weber te kry

Hi :) Thanks for your great walk thru! can you tell me why the Weber 32/36 DGV has a Vacuum Drop on the Ported Plug when Quick accelerate (from Stop to Go / Idle to Kick down).. the Distributors Vacuum Advance collapses right then when Vaccum Adavnce Timing is needed.. kind of same like connecting it to the Intake Manifold Vaccum (reacting in the wrong Way Vacuum Drop instead of UP) Thanks for your input!

@carburettorrebuildservice8964

2 жыл бұрын

The vacuum advances pipe should be connected above the butterfly on the first choke. if it is connected in the correct location then it should work correctly and the workings of the second choke should not affect it.

@motownsoulcarsrestorations1990

2 жыл бұрын

@@carburettorrebuildservice8964 Thank you! i will check again :)

Hello Gert, thank you for your videos and experience that you share - I have a weber 32/36 DGV and a weber 32/32 DGAS on my hands, can I ask you what jetting do you recommend for a stock bmw m10b16 (1573cc) Should I block all the fuel enrichment systems? Thank you and best regards from Czech rep!

@carburettorrebuildservice8964

Жыл бұрын

Hi, I would use the 32/36 just as it is. must of the 32/36 carbs came from a 1600 so it should work as is, give it a go and let me know

@marekcieslar127

Жыл бұрын

@@carburettorrebuildservice8964 Hello Gert, thank you for your response. So I've tried 32/36 (main 150 fuel, 150 air, secondary 160 fuel, 160 air, idle jets 50 primary, 55 secondary), the car runs and sounds normal on the first stage, but I don't feel any more power with the second stage, only the sound changes to "deeper burble" and I hear clicking from the engine when full throttle in lower RPM.. Is it OK or? Thank you and best regards!

Goeie dag oom. Ek wil net by oom hoor of oom carbs verkoop. Ekt nou my eerste kar gekry en dis n 1400. Ek kort al die help wat ek kan kry. As oom moontlik verkoop kan ek aseblief kintak besonderhede kry

@carburettorrebuildservice8964

3 жыл бұрын

0-6-0-6-5-4-6-9-6-6 whatsapp my asb

Hi I'm running a 272cam what is the correct tappits settings I'm currently on 35intake and 35exhaust

@koosdemeyer9105

3 жыл бұрын

Im running the R64 Lamco cam 25 intake and 30 exhaust

What would a backfire through the carb. ,while cranking ? My weber has been setting up for a while.

@carburettorrebuildservice8964

Жыл бұрын

usually a sight that the mixture is lean

Hello uncle, so I need help, I have a mk1 escort 1600 Kent, it uses that same carb, but I’m experiencing difficulty trying to start it and idle, what is a baseline for the mixture and idle speed screw, must I tune them in all the way and turn out twice as a baseline for both screws?

@carburettorrebuildservice8964

Жыл бұрын

hi, turn the air mixture screw in all the way and then two and a half turns out. turn the speed screw until you see the butterfly move, it this point it should start. you can then turn the air mixture screw in half a turn at a time until it runs smoot and no smell of unburnt fuel at the exhaust.

Were are you located at I have a Weber carburetor sitting on a 87 Honda Accord for you to look at

@carburettorrebuildservice8964

2 жыл бұрын

Hi, I am just outside Pretoria, you can WhatsApp me on 060 654 6966

I faced a problem on my toyota corona 1.8 with weber carb..idle is fine.but around 2k rpm it start bogging..im not sure whats the problem is.main jet is 138 air 160..is it in range?

@carburettorrebuildservice8964

2 жыл бұрын

Hi, what carb RE YOU USING PLEASE?

What getting I can use for my L 28 engine so I can have performance

@carburettorrebuildservice8964

2 жыл бұрын

Hi, what carb are you using or want to use?

Benimde 1600 motor bir Ford taunusum var önceden 170 km kere kadar ulaşan aracım şimdi ise 120 -130 km lere zor ulaşıyor karbüratör bakımı yaptım temizledim orinklerini contalarını değiştim ama aynı durumu fazla bi fark olmadı f66 tüp mü takmalıyım Türkiye de bulamıyorum

@carburettorrebuildservice8964

2 жыл бұрын

Silly question, did you put the jets back in the correct places, also check your float level, it could be to low and starving the carburetor on fuel. i hope this helps.

@emraherol9093

2 жыл бұрын

@@carburettorrebuildservice8964 jetlerin yerleri doğru ve şamandıra seviyesi 41mm yinede teşekkürler

Hi. Can you explain why my AC wouldn’t work when I put my Weber carb in my 1980 Honda accord? I’m new to carbs

@carburettorrebuildservice8964

2 ай бұрын

The AC (air-conditioner) has nothing to do with your carburetor, The AC unit is usually switched in by the AC controls inside you cab.

Hi just looking for some advice. I have just fitted a 32/36 webber to a 1600 twin port beetle. I made my own non restrictive manifold , from head to head. I appears to be too rich on the first stage and too lean on the second. The first stage is terribly agressive compared to to solex. Idle mixture out 3 to 4 turns , to run smooth , but ten causing a popping back fire, upon acelleration. Second stage. works initiallly but flat spots out on the road, will run with a back off and second application. Looking for suggestions for jets etc.

@carburettorrebuildservice8964

2 ай бұрын

if you have to turn the mixture screw out that much it indicated that your idle jet is to small, try one size up and see what it does.I dont have a jet chart for your carb on a beatke but this is for a 36 DCD weber on your engine - VW 1600 BEETLE venturies 23/24 main jets 110/120 Idle 45 air correction 190/180 - I would try 130 mains on first and second choke and i would use a 50 idle.

@bruceaskin9645

2 ай бұрын

@carburettorrebuildservice8964 thanks for that

Hi, what epoxy do you use on power valve?

@carburettorrebuildservice8964

2 ай бұрын

Hi, thanks for watching my videos, I use Pratley steel

Hi my 32/36 struggles in second stage splattering loudly. Emulsion tubes seem to be stuck and cannot come free. Carb is fitted to a 2.0 chev Rekord. Primary and secondary idle are 45. Primary air corrector 160 and secondary 120. Main is 116 and secondary main is 115. Struggling to set up. I guess if I can free the emulsion tubes the gunk stopping it coming free can be cleaned. Please advise how I should proceed and advise on jetting that will suit my engine. Thank you!

@carburettorrebuildservice8964

3 ай бұрын

your jetting sizes looks to small, visit my facebook page, under files i have a jet chard that could help you. must 2.0 engines jetting will be very close. web.facebook.com/groups/387029652869858/files/files

What jet sizes will fit for my 4g54 2.6L engine? Im using 32/36 also

@carburettorrebuildservice8964

3 жыл бұрын

i don't have a jet chart for the 2.6, on a 2.0 we use the following. mains 140/135 airs correction 170/125 with F50emulsion tubes in both

@foryoutubeonly2279

2 жыл бұрын

Hi i know this is a long shot. What are you running on your idle jets? And also is it primary/secondary? Thank you so much and greetings from the PH. Im also using 2.6 engine, do you think i need to try A 145/140 mains, 175/130 air correctors, and emulsion tube at f6 on both? My current jettings are 140/135 main, 165/155 air cor, and 55/55 idle and F50/F6 on emulsion tube. Thank you so much! I really love your videos. ❤️

Hallo daar, ek het n 32/36 Weber carburetor op my Toyota 4y engine. Het n flat spot problem met weg, waarna kan ek kyk. Dankie

@carburettorrebuildservice8964

5 ай бұрын

Check the accelerator pump circuit, it could also be a to small jet on the first choke. I hope it helps and thank you for watching.

Hi I see no power valve

Can anything be done about a vacuum leak at one of the shafts?

@carburettorrebuildservice8964

8 ай бұрын

Bearings can be installed, i have a video in my channel explaining how to do it.

@Ebinsugewa

8 ай бұрын

@@carburettorrebuildservice8964 thank you!

how much to rebuild a carb like this?

@carburettorrebuildservice8964

10 ай бұрын

Here in South Africa R650 excluding postage. Wharsapp me on 060 654 6966

Where are you based? I need a weber for my nissan 1400

@carburettorrebuildservice8964

2 жыл бұрын

Lindsay, i am in Pretoria. what carb are you after, you can whatsapp me on 0606546966

Ek het di powervalve se gate toe gemaak hom uitgehaal di vacuum spring uitgehaal dan is my eerste keel dood sy loop rukkerig maar 2de keel is reg hkm maak sy so

@carburettorrebuildservice8964

3 жыл бұрын

watse size jets het jy in?

@carburettorrebuildservice8964

3 жыл бұрын

het hy jou emulsion tube uit gehaal en skoon gemaak, watse size is die tube?

@koosdemeyer9105

3 жыл бұрын

@@carburettorrebuildservice8964 1st stage 160 air 122 main 2nd 135 main 132 f66 op al twee 55 idle op 1stage 50 2nd stage

@koosdemeyer9105

3 жыл бұрын

Ek het di Lamco R64 cam in ports is groter gemaak en gematch op std manifold met adaptor wat opgeweld is en n 30mm spacer stock sub

@carburettorrebuildservice8964

3 жыл бұрын

@@koosdemeyer9105 probeer 1ste main 142/145 air 155, die 160 wat jy in het sal ook werk.

Having a lekker braai while watching this

@carburettorrebuildservice8964

Жыл бұрын

thank you for the support

Weeber