Make one side of the skewer holes a notch so you can put food on them and lay them in.

@dill5500

7 ай бұрын

To close to fire

@AlgolGaming

7 ай бұрын

yeah I came to say this. if they are skewers, the the holes closest to the handles need to be notches and not holes. So you can lift them right out. Otherwise. I wouldn't call them skewers, and would call them removable grates or something.

@careyian

7 ай бұрын

Came here to say this! Was trying to figure out how to skewer my food and get it through the holes at the same time while the fire is lit. Its currently to a good solution to put a pan on, but needs to be notches on at least one side to also work as skewers.

Looks great! One suggestion is make one bigger model to. Like 1,5 or 2 times bigger.

@LouJustlou

7 ай бұрын

Yup here here in N FL fire pit season is pretty short. It would be nice to have one easy to store in shed. Mine stays outside and doesn't live too long.

What a great design. One suggestion would be have notches along the top edges so the skewers could be lifted off when they are used with meat impaled on them. As it is I am not sure how you get the food off without it going in the fire. Looks like a birthday present for son in law.

I like the other suggestions to notch one side so the skewers can be dropped in. I also like the storage hole for the bolts. Last thing I'd say would be helpful is some way to store the skewers with the kit. Only thing I can come up with so far is another plate that is just for storage. Could also be possibly the catch pan for the ashes some people have mentioned.

Awesome- if ya ad small notches on the edges above where the "skewers" go through the skewers would be easier to use as skewers. if the unit is made out of carbon sheet they can be "seasoned". Awesome n fun as usual!

Spike seems like he’s a good addition to the team. I enjoyed his voice over and I feel like he’ll be a good asset to your company. Great job! Love the content

lots of people suggested bolt storage. if you add one, you might think about doing it in the bottom of the tab that locks the unit together, so if you then place the bolts through that hole, you can't pull that one side out and it locks the whole pit together and makes it safer if the unit gets knocked around.

Flat pack! Cool! One thing I would do is make the ends of the skewers with round holes so you can attach them with the carriage bolts as to not lose them! Awesome design!!!

I think putting the notches at the top is a great idea, I also think it would be a great idea to make a stainless one and make a stainless rack to go along with the skewers.

Making it notches instead of holes on one or both sides would make it more usable! Currently, the skewers can only really be used as a grill for putting pans on, but if at least one side were notched it’d work well as a skewer too!

Just purchased two kits online. This stuff is up my alley. One will be MIG. One will be TIG. Didn't have to think twice. Never finished watching the video. Knew this was a great project.

@pprudowe

7 ай бұрын

no need to weld them... they slide together and interlock...

I found your channel searching for welding machine reviews and then stumbled on this video. I do a lot of BBQ, grilling and cooking on my channel so hit me up if you are interested in me sharing this with my viewers. I've seen similar grills but those are imported super thin, stamped out junk. I would definitely be open to show this made in the USA beefed up version.

You should add numbers or symbols on the slots & tabs that go together so that there is a self explanatory step by step system of how this is assembled. Just match the number/symbols that are next to the tabs and the slots on each side and you'll end up with a tiny fire pit. Looks cool. Godspeed meine Herren

If you put some rubber feet on the legs , it will sit on the rear seat console of my 92 suburban and won’t slip off while cruising down the road! 😮 It’s really a cool idea guys!

Need it twice size for household use!!!!! Gr8 design!!!

Add one more diamond hole at the point of the two legs meet so you can have three (3/8” longer ) carriage bolts to clamp the skewer/grates between the plates! Sides are the outer and the the legs inner to hold the bend ends internal to the pack up.

15:08 I would like to suggest you make the skewers out of the same sheet stock and slots for them to slide into. You might be able to cut these out of the scrap and they can flat pack with the rest of the grill.

Brilliant idea, well executed. Well done lads. After a few uses it's going to be messy to handle and store away. An accessory you might think about is a canvas bag to put it in.

@LiftArcStudios

7 ай бұрын

We're working on a few ideas like that :) stay tuned! - Walker

Neat little device for campers, storage is always a problem area and you solved that. The skewers are a good idea but a fail for using them as skewers as they will only cook on one side due to the weight of the handle. Love the channel do some riding in your area if it isn't raining. LOL from VB.

The skewers are much too thick for most things. The skewers being round also will allow food to twist around them. However, that probably won't happen since the skewers are also lopsided and won't properly rotate. Making them thinner and flat will allow you to rotate 180 to cook both sides. Making them another 1" or so longer with a 1/2 bend would probably be fine. But being able to rotate them is pretty key for a skewer to work properly. The bolts should have a hole to be put in on the legs to be stored also.

Just a word of advice from making pretty much the same thing years ago for my over landing setup. Make the skewers 1/2" longer and notch the end so they hook on the plate and dont slide out

I love it and would pay extra for a custom canvas pouch with slots for the skewers.

Love this design! Like other's have said though, yall need a handle too. If you add a small loop or V to the very tip of the 'handle' side of the skewars, and use longer bolts, you can use them as the handles. A lot of configurations would be possible, but I think the best would be one handle loop on each top corner, both "front" and "back" side, and with all four pointy ends pointed horizontally. They'd overlap, maybe have to deflect a little bit, but should make a nice full width handle that'd be easy to grab or lash down.

Put holes in the bottom one of the legs to store the bolts so you don't lose em once it's together.

Make it in stainless? Scallop the top on 2 longer sided so scewers can rest on top off and not be free rolling

Great idea! Tom and I could definitely use something like that. I agree with some of the other comments about the skewers being stainless steel I'm not sure about the toxicity to the food you're cooking. Then again what do I know about metal? I also agree with another comment you might want to make some kind of a little tray to go under it catch the waste for those people who were using it on their Patio instead of in the woods. I'm so glad to see you guys coming up with new ideas for the general public. Tom and I have bought absolutely everything that you have done so far. Our way of supporting you. Tay you have a great team there! A good video, show you cooking something on it that way you might be able to finesse any problems that might arise. Love all y'all! Tom and Peggy.

That's cool. only Question what is the weight, for back packing ???

These would be great for motorcycle camping

Love the channel... been watching since you cleared out the machine shop. Consider this... include a handle on the top of both, or on one, of the x shaped end plates to act as a carrying handle when the pit is stored (if you have one on each x shaped end plate then they can be used to move the pit when it is assembled). The handle would be part of the steel plate end plates that are cut with the plasma cutter. The handle would just be a little higher than the rest of the unit. Cheers...

How about a grill tray made of expanded metal big enough with turned up edges/sides that are tall enough to nest the skewers and grill pieces into the tray with the wing nuts securing it for storage?

@careyian

7 ай бұрын

I was thinking the same thing, stick that into a little canvas sleeve and it’d be perfect

Great idea, love it. My thoughts. Opposite leg of the LAS add two bolt holders or those things will disappear. Add notches along the top lip for skewers to lay in, notches would be a V cut. Then change out the skewers to square stock. This will allow for rotating the skewer and it not constantly rolling back to the heaviest side down. Keep up the good work.

Kool product. I agree regarding having skewer slots and may I add the skewers need to be longer to avoid burning our fingers when rotating them. In addition, perhaps some slots in order to pack-up/carry the pit especially after a few uses to reduce the interior soot getting all over our hands! A carrying bag would also be a very good accessory! Thanks for the "better" music from this century and not the waltz music you seem to be addicted to...

you need a box to put it in as i assume that when finished with it could be warm, definitely dirty with ashes and fat, etc. also the skewers would be better sitting in slots so they could be used as actual skewers with food skewered on them or smaller diameter skewers for cooking food on. you could offer bigger sizes as in America everything is bigger

Maybe have the option for an additional plate to be purchased to go underneath to catch any ash or embers. I think you are close to the sweet spot for size. If you go too much larger, it isn't very portable while also being relatively small for a permanent pit and you start running into increased shipping costs which pushes people to their local market. I would like to see your take on a flatpack rocket stove.

Nice Work! I feel like this is just the beginning of something bigger to come, in the shop!

Awesome. Loving these step by step tutorials on your projects. Can’t wait to see more updates and projects and many more videos soon my friends. Keep up the great craftsmanship and hard work my friend. Fab On. Weld On. Keep Making. God Bless.

Fun...now to find an agent for the shop in Vietnam for making at scale. This looks like a job for punching, not cutting.

I would try to remove as much material as possible like for example on the legs to reduce wright. Thinking if people would use it on an hike!

You need to be able to move the skewers with meat on them so go with notches on the top of the edge!!! That will make it actually useful.

Hey Spike, I like it!!!!!! I wanna buy one of these even though I do not need one. I think I will still buy one.

portapit!

Your fire pit looks great.

neat! can you create one about 3x that size? wood handles on the end of the squers to keep from burning your hands.

Gday guys. Just watching. Ok so l hope you have noticed your skewers are not useable to skewer . Try it you will find out what I mean. For the grill top maybe some stainless plate with grill lines cut into it. Maybe even just make the whole thing out of stainless. 2-3mm would be fine to make this. Love the work through guys keep it up 👍

I think you should give one to each of your patron members for xmas. Thanks. 🤪

You could also cut the customer’s name into one of the end panels to further personalize.

Love the fire pit it's awesome looking it would also be a good welding practice for noobs or even a season welder. Might have to go get one for me to check out a put it together with 308 ss filler for contrast???

Very cool i like that and love the new logo👍👍

I love it but it really needs a cooking grate so you can make hamburgers and hot dogs and not have them fall through. What you could do is make another plate and cut out enough material to have it be a grate and actually cut the skewers from that plate during the same cutting operation. That would save time making the skewers and also have someplace for the skewers to fit when the pieces are flat together for travel.

Definitely should put a diamond hole in the leg for bolt storage when the pit is being used. I’d kick those bolts into oblivion if I didn’t have a storage spot 😂

You can skeletonize the legs with some desings

love it

I like it but the skewers needs slots not holes. Also a lil bit bigger

Nice portable fire pit. I was looking for dimensions of the flat pack and also assembled? A suggestion for an accessory, a carrying case sleeve/envelope type of case. I have a deer pelt that I can sew a case if I have the dimensions. Thanks!

Can you sandwich the skewers in between the plates for storage/transport?

ya know once the fire starts you can turn off the the Acetylene. Just the ox will intensify the flame. Liquid OX will really kick it up.

Expanded metal grill grate and a full stainless version

skewers need be made out of stainless an maybe do the holes close to top notch drop in one side 👍🏻 an the flat pack pit good name

Tay! You should acquire a laser machine. First you will have better precision than plasma and less heat affected zones. But more importantly; easier prototypes! No scissors!

Should wait till end of video 124.95 good price

You need to figure out how to hook a small propane burner to it. There are a lot of places that don't allow charcoal or wood fires for fire prevention.

What design software does Spike use? Who do you do your lead in and outs?

Love the concept. But I think is too small.

Someone needs to fab up a drag knife adapter for the sharpie adapter.

How hot will those spikes get while roasting marshmallow, hotdog etc.

PortoPyroPit :D

Make it double that size. I'll buy one. Then I can keep in back of my truck for football tailgate.

First impression is the bottom air flow elements are too much - too many slots. Cut the number of slots in half to allow a slower burn and more heat control. You could deluxe-it up a little by adding a sliding air damper there as well. Otherwise, nice addition to the offerings online. OK, opinion given...good luck with sales!

powder coating or porcelain to prevent rust?

for the rest of the world, you could sell programs for cnc plasma cutter

How do you keep the Tent up when you are cooking? The skewer's, Tent Steak? Ha Ha, What do Campers eat for dinner? Tent Steak's, Ha, Ha Ha, Ha...

What are the dimensions both assembled and flat packed?

Check out the firepits here: FIREPITS: liftarcstudios.com/store/portable-fire-pit

Fire Pit🍳

Bolt and wing nut need a storing hole for when fire pit in use. So you do not loose it when in use. Squeer when stuff is on the stick should drop and lock from top. Squeer need to integrate in the flat pack as one unit for transport. Make a hole to hang the kit when not in use. Squeer shoul be stainless for food contact

Is it just me or does Spike look like Herbie the elf from Rudolph the red nosed rain deer.

I like a bigger model as this is too small for me.

What it cost?

@LiftArcStudios

7 ай бұрын

124.99 shipped to the lower 48!

Looks like a manger 😅

I mean, you might as well call it LASPIT

@LiftArcStudios

7 ай бұрын

I wanted to call it the Pocket Pit... but that's too similar to some other products we don't really want to associate ourselves with 😂 - Walker

Are you worried Baby Jesus will sue for copyright infringement?

need to add small ridges/dimples along the top edge for the skewers to rest in

God this guy is annoying. If I see him again I'm unsubscribing, this is just flat out spam.

@LiftArcStudios

6 күн бұрын

Spikes a very important part of our team and one of the greatest guys we know.