WE BUILT A CAR CRUSHER!
Автокөліктер мен көлік құралдары
Finally finished the car crusher! It took longer than I thought to complete, but I think it was worth it. Let me know what you think!
🔔 Subscribe for more / hardcorefab
Visit our website: www.hardcorefab.com
Visit our TeeSpring Store: hardcore-fab.creator-spring.com/
Thanks for watching!
#carcrusher #cowboycarcrushing #cowboy_car_crushing #hardcorefab #homemade #hulksmash
#hulksmasher
Пікірлер: 942
If you haven't watched it yet, the best smash is at 10:00. At least that's my favorite!
@imallowedmyopinionok2354
2 жыл бұрын
Cheers mate. That saved 10 wasted minutes👍
@theherocatchannel5517
2 жыл бұрын
He smash the car in the camera!!! 🤣
@WildWanderingInWestVirginia
2 жыл бұрын
@@imallowedmyopinionok2354 0
@dubiousf00d
2 жыл бұрын
What a rescue mission for that camera lmao
@butchdavis2703
2 жыл бұрын
Put 2 smashed cars on top of each other and smash them again please
In the early 80's my friend and I used to visit a scrapyard west of Montreal that had a similar crusher. What differed regarding efficiency between theirs and yours is the following: the pivoting point was only a few inches from the ground. As well an important factor of physics is sheer mass: the swivel structure was filled with concrete increasing the weight of dropping mass, thus the cars in a single drop would have been 12 inches high.
We got one here almost identical to yours that was built almost 35 years ago, quit using it because it took too long to cycle, had issues with the cable and winch , but most of all was unsafe due to no control after it was tripped. Also doesn't work well on vans or SUV's because it blows them out too wide. Hydraulic is really the only way to go. And eventually your hinges will fail and when it does it's not pretty.
@breadfan9
6 ай бұрын
Where can i put my ex?
@cryptodtgg9702
4 ай бұрын
Facts
Great job on the car crusher dude I want to see what it does if you stack one on top of another then drop it I wonder how far it will crush it
@TheLowlow1968
2 жыл бұрын
Me too, I was going to post the same comment. Can't wait to see this happen!
@sambell385
2 жыл бұрын
I wonder what would happen if they turn the car around so that it smashes more of the motor side of the car
@tonydobek8908
2 жыл бұрын
EXACTLY
@EternalResonance
2 жыл бұрын
can you submit this to the nearest city as an option for execution? of course only for the atrocious people who deserve it.
@sambell385
2 жыл бұрын
@@EternalResonance which ones are that you know occasionally humans do make mistakes and convict the wrong person
Hey Tony Another successful build ! I would like to see a car put in with the engine facing away from the pivot as well as two cars at the same time. Put a car in upside down. Stand a car on end. Put one on it's side. I mean, sense we are playing, lets try it all ! Thanx fur the entertainment. Now about the upcoming build with the Super Singles ? Play Safe, Be Well
@HardCoreFab
2 жыл бұрын
Hmmmm that does sound like a good time!
@user-zt6bt8dp2c
2 жыл бұрын
@@HardCoreFab might as well throw some semi’s in there to.
@112Dongen
2 жыл бұрын
After crushing stak 2 or 3 and see how flat that gets
@dapperdingo
2 жыл бұрын
Make sure that if they still have running engines, you red line 'em during the crushing process. But WAIT! Let me go make some popcorn.
Love it. You should pour concrete in the top 6ft of it. Reduce the bounce add a few ton.
@c50ge
2 жыл бұрын
I think the winch is already pumping it’s little guts out already with the load it’s lifting already.
@HardCoreFab
2 жыл бұрын
30k winch whole lid is less then 13K and only picking up one end. The winch is fine!
@thomasvennekens4137
2 жыл бұрын
maybe sand ? concrete might crack if you dont reinforce it
That thing is brutal. I love it. But I almost cried when you crusher the Intrepid.
That's pretty bad ass! You can crush as much of those ford's as you want! Lol
@HardCoreFab
2 жыл бұрын
Yeah not much lost there. Lol
Cool build and looks like it works pretty good. You always impress with what you build.
The crusher is cool but that dodge boom truck is amazing. I can’t believe what some people will scrap I would love to own that thing
What happens if you stack 2 smashed cars on each other and resmash them together ? Could you get another foot shorter on each car? May be easier to stack?
@C69FH
2 жыл бұрын
Yes... this would be worth watching
@Frank-Thoresen
2 жыл бұрын
Adding a bit more weight to the lid I think it would crush two cars at once. I still think that the hight between the bed and the lid is a bit too high. The hood and trunk are not affected much by the crushing
@HardCoreFab
2 жыл бұрын
We are planning on playing with it more soon
@gsp911
2 жыл бұрын
@@HardCoreFab You could also try tilting the car to the side and giving it one more smash. 😎
@watahyahknow
2 жыл бұрын
if the engines are still in the cars they probably turn intoo a wedge shape , maibe if the stack them with the noses in oposite direction the engines can embed themselfes in the trunkspace
Very cool build for sure. Looking forward to seeing how it all holds up.
Great job. Works better than I thought it would.
@spencergreenhill7728
2 жыл бұрын
Hey, give him credit, at least he was out doing something not sitting on your dead dupas doing nothing.
I would look to some sort of cable release and wieght the hook so you can free spool it down because the rapid unspooling seems like that will be hard on the winch. Cool build
@HardCoreFab
2 жыл бұрын
When the dog on the winch is disengaged the gears in the winch aren't turning so there is no stress on the winch.
@scubasteve7946
2 жыл бұрын
I'm thinking he means like the bushings in the drum etc spinning pretty fast. Probably hurt it over time. A quick disconnect on the hook end of the cable might prevent that. Sort of like a large car door latch you could pull with a rope on the cable hook end.
@tractorboy31
2 жыл бұрын
@@scubasteve7946 yes plus cable whipping at end
Hard to believe y’all painted it before you tested it.
@HardCoreFab
2 жыл бұрын
Got to look fresh for the first car
@HardCoreFab
2 жыл бұрын
I painted my vehicles before I drive them too! LOL
I was going to say that you guys should keep the car off center to the hinges to reduce the leverage on the hinges 🧐👍 great job Anthony 😎
Congrats Tony on building the Hulksmasher to show us how it smashes cars. agree that the cars need to be higher to flat it more. cool video.
Stack 2 smashed cars together on it and smash
That’s awesome!!
“”HULK MAD… HULK SMASH CARS!!! I read you had a lot of suggestions, may I make another, turn the car around so the most weight hits the engine compartment where the most structure is. Cool build!!!
Nice Job! I'm in my fifties now but when I was a teenager, I drew up plans for a crusher just like this design. One correction I see is you'll need to push the doors in so it will fit on a semi trailer correctly. Overall, I'm jealous that you have this crusher and I don't.
Built pretty much the same car crusher 45 years ago. 20 inch high beams and 3/4 steel plate. Burned up to Lincoln welders, welding at damn thing up. We use the 5-ton rear axle and the GMC V6 engine. It worked okay but it was extremely time-consuming and Messy. They ended up just letting the regular car crushers come in.
Wow that works really well. Good job!
A paint can or watermelon on each would be cool LOL Could hang a few shirts across the back wall and have a new merch line 😁
That’s Excellent Job Question will those cars look Wide when I get crushed will they fit on a tractor trailer without all the hanging
@HardCoreFab
2 жыл бұрын
None that we have crushed so far would be too wide to go on a truck. Having that said I think you would need to push the doors in on a pick up or a Van to keep them from being too wide
Hell ya looks fun !
That was too cool. Great job guys 👍👍🇨🇱
I'm impressed- but I think it would do better if the hinge was level with the table! also if you load the cars to the end of the swing it will make em flatter!😁
@pipegang6497
2 жыл бұрын
I was gonna ask him the same thing why did he position the hinge pin so high off the surface you figure it would be more stable if it were attached to the floor
@genehasenbuhler2594
2 жыл бұрын
@@pipegang6497 that's my way of thinking! I agree 100%.
@Masterfab93
2 жыл бұрын
The only reason for the elevated hinge is it allows for better momentum and keeps it from binding up.
@mikethatguy27
2 жыл бұрын
If hinge was level it wouldn't be able to crush 'flat' it would leave the cars less crushed on back side. Therefore could not stack the crushed cars. 🤷 That's just my weird little brain. Who knows 😆🙌✌
@lukelegg9915
2 жыл бұрын
@@mikethatguy27 you are correct, plus the engine is the most un crushable thing in the car, so having it level would not work
You never sees to impress me from Belding cars to crushing them lol
@brandonsciulli774
2 жыл бұрын
Seize
@bobd9193
2 жыл бұрын
@@brandonsciulli774 If you're gonna act like you're smarter than someone else and correct they're spelling, you ought to know how to spell it yourself. The word is "cease", As in "cease and desist"
@brandonsciulli774
2 жыл бұрын
@@bobd9193 hehehe
Way. Way. Way cool.. liability insurance?? We don’t need no stinking liability insurance.
My old boss built a crusher like that but he used two hydraulic cylinders off a old grain truck he got in. It to this day works very well. Great job guys!
Well it does smash cars, I deny that but thats not all flat really! It just crushes roofs! For flattening it all out, you got to raise the platform on where the car sits, so flapper comes sandwiching car in between, but because your sitting ground is way below your hinges mechanism, it doesn't fully crush properly. Its not hard to make, just a shorter panel to leave space for hinges to close in normally and just laying smasher more firmly and tighter on the crushed car. Aside from all above... Crushed cars looked in a real good shape though to be crushed, Except for last one!
@cornnatron3030
2 жыл бұрын
You will most likely run in to the problem that the lever arm has to be double the length and double the weight to flatten it completly then. Cause the lever gets momentum loss as soon as it makes contact , now the top part of the lever (fastest most momentum) makes contact first with a lower hinge the slowest traveling part would make contact first and would slow the smasher down giving it less momentum and less power.
@georgerenton965
2 жыл бұрын
It only has to crush the roof down to make it a level base to stack other crushed cars on top so they can be stacked on top of one another on the truck.
Did you get the go-pro out?LOL!
@HardCoreFab
2 жыл бұрын
Lol Surprisingly it was unscathed
First video I've watched on this channel. Can't wait to watch more👍
Awesome build!
Stack 2 smashed cars then smash them again! Lol Definitely turnd out cool. Could watch it work all day!
best thing that could happen to a ford
@clarrnceclark9482
7 ай бұрын
Yeah because the chevys are all gone rusted to pc or crushed
@trainnerd3029
7 ай бұрын
I drove a Chevrolet for a while… Then I got a job!
@cjpow4867
7 ай бұрын
The panther platform cars are insanely reliable lol
@slotripper
7 ай бұрын
Obviously a genuine millenial or the parent of one.😂
@k.a.d.msrt8326
7 ай бұрын
100%
That’s wild!
Very well built. I love it!!!
@HardCoreFab
4 ай бұрын
Thank you!
Got here by accident stayed for duration cause content!! Awesome guys
Great idea . Yup my thought was the pivot point why so high however .. flatten a car or 2 then double stack and flatten them with one on top of the other. Should have a good result ..
Someone needs to paint a lime green palm on the underside.
I've worked in the salvage business for years. And I think thing is awesome!!! Does a out standing job! I'd Bee proud to have or use a piece of equipment like that. My hat off to y'all.
@ThatRustLife
2 жыл бұрын
Thank you!
@HardCoreFab
2 жыл бұрын
Thanks man!
What a satisfying crush guys love.love that beast u made
I am a happier man now and would love to see 2 cars stacked up for a second crush. Such satisfying entertainment.
That's a much better crush with the tires and wheels off the car!!
sweet build, need to get the slomo guys in to catch the amazing power of this crusher
@HardCoreFab
2 жыл бұрын
That would be fun!
Awesome
What a great build . Looking in from Ireland 🇮🇪
GEEEZ!!!that's awesome! That "wrecker truck" is a winch truck with gin poles, it's got oddly mounted poles but it's super cool
@HardCoreFab
2 жыл бұрын
The bed is junk but the rest is sweet!
That thing is merciless… I love it
That was excellent! Nice job 👍
Sickeningly satisfying. LOL. TOO COOL GUYS!
Car-nage! Awesome
The crushed cars reminds me Panthermobile.... 😂
awesome
My dad owned Anderson Auto Wrecking in Walla Walla in the late 70's early 80's. They built one similar out of old decommisioned water locks (movable dam). They plated the faces with 1" thick steel and they filled the top (moving part) and bottom with sand. It worked so well that it was shearing the heads off V8's. One day he had a bunch of railroad track that came in, so they cut it and through it in the cars before crushing. The steel scrap / shredding company in Seattle called up and the CEO flew out to see his crusher and told him never to put railroad track in the cars again. Apparently the railroad tracks really messed up the shredding machines.
@ryanstone8209
2 жыл бұрын
His was a little different than your design, but very similar. It would winch the top up vertically, then had big hydraulic rams that would lift the pivot point and top another 6 feet or so. When he would release the pin, the top would rotate to approximately 90 before allowing the pin side to drop as well.
@HardCoreFab
2 жыл бұрын
Hahaha yeah the shedders don't like that big thick iron in car body's!
AWESOME!
That has to be cheaper than running a hydraulic press type crusher. Maybe even quicker as well
@HardCoreFab
2 жыл бұрын
100%
The use of kinetic stored energy is a novel elegant approach. Be mindful of forces on hinge point..and safety when its up
that is really really cool mate, great work
Very impressive, moves so fast you better be paying attention all the time to avoid a disaster.
@HardCoreFab
9 ай бұрын
Right!
Pancaked em. Should make for easy stacking.
when the back plate slid into position, all I could think of is Jim Carrey saying "Like a glove!"
Love it!!! Good job!!
That's awesome. You should put a car in on its side to see how skinny it can get
That whole thing whips around a lot... Long as I don't have to be around it, you do you Pal.
That's awesome man!!!!
Great video! Thanks for sharing.
@HardCoreFab
2 жыл бұрын
Thanks for watching!
That looks waaay risky, bro! …but fun!!!
Well that’s just awesome and now you can really stack those things up on the scrap trailer and send them down the road
Very satisfying watching that car get crushed
Absolutely awesome!💯🙌✌
"If you build it, they will come"
I showed my car this video, it’s never broken down since.
@HardCoreFab
Жыл бұрын
Lol
This is so satisfying
It's certainly an awesome attempt at building a home made crusher! Well done guys!👍😀
Very clever!
It'll buff out... LOL! Seriously, how has this video not had 1M views?!
@HardCoreFab
2 жыл бұрын
😂😂😂😂
@ccahill2322
2 жыл бұрын
kevat310, it is not because there are not enough maroons.
Cool!!!
The first time building something almost always takes longer than you think it would.
Cool stuff. Always fun to smash some things. Happy Smashing!
Like any project you figure things out as you go. Like your hydraulics, perfect for testing. Late maybe upgrade to bigger motor and pump. If you wanted to make it mobile, put hinges on the struts and tower. Could use the winch to erect it at the new sight. Best of luck with it all.
Built one of those when I was a kid using Legos and glue. It was only a foot long. We flattened bugs with it. Cycled much faster than the one in the video.
@HardCoreFab
27 күн бұрын
LMAO!
Way cool!
You are a very handsome bearded man! Great job on the "Crusher". Ya'll be careful. That could hurt really bad.
Nice job !!! Need some safety shields on the sids
As my Grandpa use to always tell me (every time he saw me, it seemed); "If you're going to waste your life, you might as well have fun while you're at it."
@HardCoreFab
2 жыл бұрын
100%
Awsome build you could probably fill the bit your lifting with winch with concrete that'll be interesting
That’s pretty awesome
I think i would load the cars with the engine towards the end of the smasher. I would also make another maybe 6"-10" plate to place on the platform under smaller cars to smash them even flatter since the hinge is so high. That or spin the cars around and hit them a second time might even work.
@1stontario
2 жыл бұрын
maybe have the hinge capable of dropping as it falls.
@Demonlord468
2 жыл бұрын
@@1stontario Would be easier and safer to just remake the hinge in such a way its adjustable and able to move up or down for thicker/thinner vehicles. That hinge needs to be rigid as possible to be safe as possible.
How to make instant Lowriders. You should've included War's lowrider song in the background of the video 😅
@HardCoreFab
2 жыл бұрын
🤣🤣🤣🤣 yes I should have
Hinge needs to be closer to the table , but not level, say 6"-12", good video
Big props to the camera man that sat in the car at the end🙏
@HardCoreFab
2 жыл бұрын
LOL camera yes man NO!
awesome build ...it seems to crush a little better on cars that had tires removed...no rubber !!
@HardCoreFab
2 жыл бұрын
Yes it does!
That's Cool as Hell, I think Cowboy Car Crushing would Love this Crusher.
Notice a common denominator in the cars he crushed? 3 out of 4 were Ford's.
@HardCoreFab
2 жыл бұрын
LOL funny how that works!
I believe you might want to mount your snatch block on the lid or load. This would allow you to increase the weight on the lid
Cool 😎
Love it, especially the comments from people who probably couldn't even weld to bolts together telling you how they'd build it 👍
@HardCoreFab
2 жыл бұрын
It is the world we live in!!!