This will help me tremendously. Great step by step. Easy to follow. I pulled the cover and found some tiny ball bearings and one of the pins for the one way clutch. After watching this video I am heading out to complete the inspection and repair. Thanks, Allan

Enjoyed the video. Just picked up 2008 650 can am outlander. Thanks for sharing your video. I'll know what to look at for the early warning signs. Keep posting brother 🍻🎶🇨🇦

@JPar9577

3 жыл бұрын

Appreciate it glad the video could help you

You saved me a lot of trouble and a shop bill man I appreciate it

@JPar9577

3 жыл бұрын

No problem glad I could help

In Australia tried the righty loosey technique you mentioned but was actually regular thread. Lucky we didn’t go too hard at it

Great Video. Thank you for taking the time to make the video. Working on the first side by side and doing some clutch work. This helps tremendously.

@JPar9577

3 жыл бұрын

Glad I could be of help!!

Hey thank you for going to the trouble of creating this. Very Helpful.

@JPar9577

2 жыл бұрын

No problem glad I could help!

Omg brother that clutch it’s easier than the Polaris 😳.really good video btw 👍🏻👍🏻

Was hoping you showed how to install the bolt on secondary clutch. My bolt on secondary clutch sheared off. Just taking it out of storage and getting it ready for the the summer I fixed it but did not have the right tool to hold the secondary clutch was gonna use a piece of wood but just had the dealer torque it for me 12 to 15 pounds than a 180ﾟ. The tool to hold the secondary corlayeah it's looking very cool lunch is a $180 over here. Maybe I should invest in it just in case. Great video thank you for sharing

Very good detail explaining 👌

Appreciate you making the videos on Can-Am any tips on maintenance care or replace wear and tear whatnot Would gladly watch Thanks bud

@JPar9577

3 жыл бұрын

No problem thanks for your input!! It's greatly appreciated!

Thanks for posting this video. I think I'm experiencing this. I got some muddy water in the air intake and i seized up the secondary clutch. the bike wouldn't move. After I cleaned it up the bike started creeping so when I can I'm going to take apart and clean the primary clutch. Thanks Again I hope this works for me.

@JPar9577

3 жыл бұрын

Awesome im glad I could help!!

It Just happened to me last night. I broke everything down today. Taking my time cleaning it . 2 things..1st I like to get a clutch upgrade 2022 450 Can Am Outlander DPS cause I will be getting bigger tires. can you send info on what you recommend? and #2 before you put on the box did you rotate secondary clutch 180* ? cause you didn't show it on video. thanks for the tips great video!!

thank you great tips n how to i got a mavrick but i thinks its same setup

Have you ever had a belt pop and when you replace it all gears are reverse? It was perfectly fine before now if you put it in high it’s reverse, low it’s reverse, and neutral and park same thing.

Nice job and good video💪heloo from Romania

@JPar9577

3 жыл бұрын

Thanks for the support!!!

I this same thing happen to me, I actually had to pull the bushings out and clean the dirt that was behind them, the dirt was making then push out and cause friction not allowing the clutch to operate properly

@JPar9577

2 жыл бұрын

Yeah if you ever flood the belt box that dirt gets in everywhere

I have a squeak noice coming out from primary clutch and gears won’t engage. Any suggestions?

thanks for this!

Thanks for the video. Did you need a special tool to hold both pulleys while torquing them back in place?

@JPar9577

3 жыл бұрын

Yes you do need a tool to hold them still and torque them

@iridecommando1485

3 жыл бұрын

Thanks

This is a good one!

What do you recommend for torquing them on and off? To keep it from spinning? I have to remove mine and clean it. I had a critter decide it was a good place to store food for winter 😢

@JPar9577

3 жыл бұрын

They make a special tool to hold them in place while you tourqe them. In a pinch I've improvised using a piece of wood but I do not recommend doing that because It can damage the clutch if not careful

@areenders

3 жыл бұрын

@@JPar9577 I’m trying to locate the tool.. I can’t hold it tight enough to get the factory nut off. Thoughts? The nut itself is 17mm... what size clutch socket do I need?

@JPar9577

3 жыл бұрын

@@areenders what are you referring to as the clutch socket?

Tks for sharing. I have to fix a 650 that has the same issue. Tks for showing the little springs and pin bullshit set up 🤣. Tin Can waaay over rated imo. 🤙🏻

Should I let the parts sit over night or take em out of the water? I have the bearing in the water as well that you said be careful of because of the small springs which wasn't to bad they fell out in my hand. My clutch wouldn't even move at all, and so I have it all in a bin of dawn blue dish soap and cold water. I don't wanna ruin anything, and I couldn't get the other clutch off.

@JPar9577

3 жыл бұрын

You can let me sit as long as you want the main Thing is making sure everything is clean and dry when it goes back together!

@kingdon9690

3 жыл бұрын

@@JPar9577 awesome ty I appreciate it man, I'll dry everything up tomorrow and put it back together

@kingdon9690

3 жыл бұрын

@@JPar9577 one more question is the primary clutch supposed to be hard putting back together? It was hard getting the spider part out and now it's fighting to go back together like the magnets are stopping it

@kingdon9690

3 жыл бұрын

@@JPar9577 did you grease the clutch bearing before putting it back on the shaft over the two little springs?

@JPar9577

3 жыл бұрын

@@kingdon9690 yes I did!

Did you pull off the inner sheave i have never been able to get mine off

@JPar9577

3 жыл бұрын

No I left the inner sheave on they make a special puller to remove the inner I've never removed it myself

Hey bro I might need your help with some My secondary clutch won’t come off I took the bolt out The spray ain’t push it out the spring is loose just hit me back up and I’ll send you a video for you to see what I’m talking about

@JPar9577

3 жыл бұрын

Yeah sometimes they do that may need to spray some pb blaster on it and tap it with a rubber mallet don't hit it hard or it will break just need to work it loose

At about 1000 miles, my belt started slipping so I figured it was time for a new belt anyways. So I went ahead and put a maverick belt on it. 300 miles later, it’s slipping again.

@JPar9577

3 жыл бұрын

Thats strange maybe you can try resurfacing the clutch faces? That may help

I have a can an renegade 1000 xxc and when its NOT started the gear shifter moves freely wen its started the shifter is stuck in park and i can only select reverse unless i turn it off and move it to another gear but then wen it starts it pulls forward or back depending on the gear im in ... any suggestions ? Do you think its worth doing what you did in this video ? Thanks with love from the uk

@JPar9577

3 жыл бұрын

Sounds like the clutch is stuck i would definitely try cleaning the clutches like i did in this video!!

@boristheblade0075

3 жыл бұрын

Cleaned the clutches today like in this video and also made sure the one way bearing moved freely and it does but still no change to my problem ... ive now got no idea and this lockdown of the uk isnt helping as there in no quad mechanics open and to top it off its due to snow tonight and my can am is broken 😭😭HELP PLEASE

@JPar9577

3 жыл бұрын

@@boristheblade0075 did you clean both clutches? 🤔

@boristheblade0075

3 жыл бұрын

@@JPar9577 yes i did

@JPar9577

3 жыл бұрын

@@boristheblade0075 is the primary clutch sliding back and forth like it should while revving when in park or neutral?

What size of bolt was that to spread the secondary?

@stuarthealey326

3 жыл бұрын

M8x1.25 thread pitch

@rickylee9067

Жыл бұрын

@@stuarthealey326 thats awesome thanks

Should be marking everything those are balanced

Mien is like that thanks

Hey brother I have outlander 800 n clutch area making grinding noise u know what it could be

@JPar9577

3 жыл бұрын

Have you took clutches out and cleaned them? also may want to grease the one way bearing

@JuanRamirez-dv4ou

3 жыл бұрын

Yes I have I started the bike without clutch on left side n can still here noise almost like it's coming from shaft...is that shaft suppose to move a tiny bit like in n out cuz it does a tiny bit....any suggestions....

@JuanRamirez-dv4ou

3 жыл бұрын

Wanted to add video on here but how do I do that

@JPar9577

3 жыл бұрын

You have to click the add video button and upload your video not sure what device your using, it may be different on your device im not sure.

@JuanRamirez-dv4ou

3 жыл бұрын

I did it's on their

Mine just spins & won’t open & close. In gear it won’t move.

@JPar9577

3 жыл бұрын

Probably stuck have you took it apart and cleaned it real good?

First problem is buying junk Walmart tools second having dead battery's 3rd it's a 450