Fun fact, the blade spindles are actually not greaseable despite having zirk fittings, the bearings inside the spindles actually contain SEALED bearings, so you actually gotta take them apart and pop the inner side of the bearing seal off to grease will actually touch the bearing

People are dying to live next to this man.

@MrSaemichlaus

8 жыл бұрын

Well he's full repairing a lady's ride and putting up clickbait titles, if that doesn't get him the attention...

Before you drain the oil remove the dipstick! This will allow better flow. Did you say "warsh"?

Use " Green Slime Tire Sealant " , Use Tire plugs like You have ( keeps the dirt out of the hole ) . got to give a " Twist " Two to Three Turns to make a Knot on the Inside of the Tire , before you pull the plug install tool out .

Thank you for your guidance and excellent video.

Our x394 is a beast at mowing

My lawnmower, the music of my people..lol

Neighbor must be good looking

MY TORO TITAN MAX IS A BEAST AT MOWING ITS BADDER MEANER AND THE MOST STRONGEST MOWER

Just put a tube in the tire! 💥 Boom, fixed!

Powerwashing a deck is a good way to force water and contaminants past the bearing seals... use an air compressor / blow gun instead... every rusty / rotten deere deck out there was either stored outside (horrible) or power-sprayed regularly (can be almost as bad)... particularly the shitty Tennessee-made decks

Shoulda got a craftsman, actually they're all pretty much the same

They are all made by MTD! John Deere is just a name anymore, lawn tractors are lawn tractors, made by MTD!

Uh oh Uh oh 🤣😂🤣😂🤣😂

lol 😂

That's enough trying to copy AvE...

It's a lot easier to rasp and shove the plug in when you put air in the tire first.

your need to twist the plug2 or 3 times befor you yank the tool out helps seal it

LOL..wait till the oil drains till you remove the filter. That is always a smart idea

Just a bit of advice, break loose the filter to make sure it will come off then hand tighten again. Take a punch an put a hole in the filter so it drains in the pan and not on your frame. Saves clean up and helps prevent sludge build up.

Heck those blades look perfect!!! You ought to see what they look like after a month down here in Georgia. Both sides of the blade look about the same!

@D40-MilitiaMedia

8 жыл бұрын

+former pilgrim an old lady in a city owned this though too lol, i give it a week outside city limits to become what you just described! hahaha

@firenado4295

8 жыл бұрын

I had my blades on for 13 years and they were so blunt they weren't balanced so when I reved them faster giggled a lot

I love how he just puts that pin back in there like uh oh xD lmao good one

There is a common misconception when airing up tires. The "max psi" stamped on a tire doesn't mean that it's the correct psi you need...it's only what it says, the "max psi" that can be used. The correct psi needed varies depending on what the tire is on. (The tire manufacturer doesn't know if the tire will be on something that weighs 50 lbs or 500 lbs.) An easy test is to wet a spot of concrete and drive thru it. If the track going out of the wet spot is less than full width it's over inflated.

7:00 "Turd looking things with that goopy stuff" Ha! Love those technical terms. :)

Good tip about oil drooling onto the belt! Just brought a 2016 D125 , 20 HP, 42 inch deck home. that oil looked like it was in there for the entire 300 hours! ( I was waiting for you to sit in the river! lol)

I have a john deere x300 with a 48 inch deck and I'm having trouble getting the deck off. How'd you do it?

Hey BILLSTMAXX I love how you said your 2720 shrank into the smaller tractor. I just cracked up when you said that!!

we have an x300 and we have been mowing 4 years and we mow 16 acres still running just fine most is up hill

Motion lotion hahahaha

i love working on john deer riders myself. i always have good luck with them.

on my old jd 317 lawn tractor, the mower deck I have for it has got to weigh at least 250 lbs, I'm an average sized person so when I have to lift it up with one hand while hooking up the belt, it's impossible, the new mowers are easy

At first you scared me be cause I washed mine like an hour ago.

@michaeltomlinson4761

3 жыл бұрын

Same🤣

i usually put some cement poop on the plug strip before firing it in the leaking tire. nice tractor looks like an updated version of my sabre

PS to my former post (I ran out of space). The former tip from me was a general rule of thumb technique for tires with "square" sidewall/tread areas. For more "rounded" sidewall/tread areas you obviously wouldn't try to get the full tread width in the ground (since part of the tread is actually on the sidewall). And when I say "full tread width" I mean the "majority". Meaning....you don't want your tire to be running (leaving a track) on just a small percentage of the width of the tread.

Careful washing the deck. A friend of mine deck washed his JD after mowing a few times, then went out to mow one day and heard a loud BANG! accompanied with a hard thud feeling under his feet. The bearings under the deck are water resistant, not waterproof. The washing allowed too much grease to leak from the deck causing the failure. Ritchie told him that washing the deck would void his warranty, even though the fittings and hose connector are included with the machine!

You should always check the "manual for machine that the tire is on" for proper air pressure. The tire manufacturer has no idea what the tire will be used on so all they can do is give you "maximum tire pressure". For instance, I have a large ZTR and the proper psi for the rear tires is 8 lbs....but....the maz psi printed on the tire is 32 lbs. If you inflate to that it rides like a log wagon and only runs on the center of the tread.

Do you still do decals?

Is that an Elmira farm service sticker on the rear?

"belts are gay, i like the shafts more" LOL!

I need a neighbor like you. Our GT225 is in the shop right now, gonna run 4 - 500.00 for a service. Hunnert bux just to come pick it up.

Excuse me sir what kind of air pump do you have?

Are you in cahoots with Ave?

PSS I own a commercial zero turn mower that operates nicely at 6-9 psi on all 4. This provides a much, much softer ride than if I aired them up to the max (stated on the tire) of 28 psi.

17 hp kawasaki looks a lot like a kohler though. that one has the proprietary star bldes on them with the cheap ass craftsman spindles on them. looks like she ran it really low on oil. i never use the goop the plugs are usually good enough by themselves.when you put those plugs in there you are supposed to twist them around a few times before you pull the "fork" out so that it hels form a knott and plugs the hole better

Loved the sound effects

@FMF666 thanks!!!!! :)

I have a John Deere d110 with only 11 hours on it. It will not move forward or reverse. The wheels in the rear seem locked, The rear pin is pulled out so it can move forward. Can not get anything to move any advice?

@vadawaii

8 жыл бұрын

I think the pin is supposed to be in instead of out. Good luck!

@michaelkuzmadutton7879

8 жыл бұрын

You need an old john deere 212. Something tells me that would be a perfect tractor for you. There super fast and beafie.

@daddydubz88

Жыл бұрын

The 110 has the plastic shitty transmission as well. Always get a 130 or higher with the 100 series

Hey bill, Is it sometimes creepy living beside a Cemetery???

@tonymontana897

4 жыл бұрын

I'd love to live next to a cemetery. The best neighbours you'll ever have !

@danielebrparish4271

3 жыл бұрын

You can't find quieter neighbors.

@Safwentay really? super thanks.

Engine made in Maryville, MO

Yea you wash it and it turns into a Big Box John Deere.....

i already learned my lesson. i washed my 65 hp 5310 loader and i came out to use it to see a 40hp 301-a!

Funny, why has no one else thought of this idea.

no rubber cement before u put in the tire patch?

@vector6977

8 жыл бұрын

They already have goopy stuff on them.

@yu-gi-ohconcajones2509

8 жыл бұрын

vector6977 that's not enough... they come supplied with rubber cement as well... to lock the plug in place...this was done incorrectly

@alabob20

8 жыл бұрын

+YU-GI-OH Con Cajones cheap ones come with cement. most are self vulcanizing. all that is need generally is some soapy fluid to help it slide in. not done incorrectly.

These small John Deere garden/lawn tractors get bad reviews on all the comments/review boards I've seen. I almost bought one when I replaced my 12-yo Craftsmen tractor and glad I didn't.

4:55 LOOOOOOOOOOOL

at least that is a one bolt for each blade all the newer ones have 2 bolts for each blade, makes it harder to get on and off.

put air in the tires as u ruffin up the hole with the patching tool much easier

meanwhile, back at the ranch

I see you have quiet neighbours on the side there. ..

Thats nice of you to do that for her Bill

Looks like one of those HomeDumpo Deere's junk...

that pretty sweet i have an X340 with a 26hp kawasaki with a 54inch deck its a monster of a mower!

Another GREAT video turd,tities all the things that a man talks about while working in the shop on tractors .Sounds like a day at my shop

Honey, I shrunk the tractor!!! Choooch!!

I have a big yard to but no grave

When check oil level on that Kawasaki you not suppose to screw the cap down. You just touch the cap to threads on the dip stick tube, there isn't a lot of oil in that sump. and the amount of oil that came out of it wasn't much. You said that been 2 years since last service, I have 25hp Kawasaki and it takes almost 2 quarts of multiple grade oil. I don't care for the small oil filter that Kawasaki uses. I really enjoy your video's great work very time consuming.

YOU, FORGOT TO PUT THE RUBBER CEMENT. ON THE RUBBER PLUG. BEFORE YOU ,PUSHED INTO THE TIRE .

Great vid as always!

he said bung the hole up

how was it "Dickered" what do you mean by that, why don't wash it?

Idk why??? But I was interested in this video haha

@biggdaddy2001 about 200' away

is it a mulsher

I subbed so be happy

2 years old? she still looks new! we put 400 hours a year on our machines

You have alot of close-by neighbors there my friend.

Sorry I didn't put all this on one post , You should of put air in the tire before trying to plug it ,It would have held enough air to make the plugging a heck of a lot easier!!

Your a funny fella mate :-) good vid

what is purple soap

I agree. Gay is not the right thing to say. This guy is cool. Not gay.

@Peppercatkeith good call...

2 acres that's small I have over like 20 acres to mow I don't have a jd mower I use a tank it's zero turn I like it I don't know the actual company name

It probably shrunk in the dryer.

you need a foam lance to hook up to that pressure washer !!!!

DO NOT WASH UR JOHN DEERE THE FARMALLS WILL CATCH IT

Bill has changed

@killstrees

9 жыл бұрын

Alex Reents Yeah, ever since he stopped doing stuff with puglife, he has gotten a lot better. I still think the way he used to talk was a little more entertaining at times just because, but he's much better off without the puglife influence.

Dont wash your John Deere, buy a Valmet

Reminds me of AvE.

well don't put it on high heat dry, only spin and fluff....lmao

Don't wash it. It will shrink into one of those rear engine jobs.

don't mean to mess with you while your on a roll . But if you air up the tire you'll find it works much better. In fact you might not be able to accomplish your task without airing it up..

thats a nice x300 i have a X320 myself \

very very very very cool

can you give me a power fist?

I really hope you didn't re-use the old oil filter...never do that

to use the word gay in that context is bad it implies being gay is bad. please do not misuse words like that.

@MBarker397

9 жыл бұрын

Gay

@TheLadsOutdoors

9 жыл бұрын

yer gayyyyy

@TheLadsOutdoors

9 жыл бұрын

hahahahahha lmfao George Great Hes probably gay thats why hes saying it... GAYYYYYYYYYYYYYYYYYYYYYY Discord

@thegrimreaperz798

9 жыл бұрын

NorthernOutdoors asshwole

@thegrimreaperz798

9 жыл бұрын

NorthernOutdoors asshwole

you... live next to a cemetry.

i see youve been watchin the 1puglife movies on the youtube tv eh... stove pipes yer sister

@WTFtheGreatOutdoors

9 жыл бұрын

NorthernOutdoors I heard him say "Antler" hehe

o oh... o OH ,,, O OH... haha nice vid man