Do you think a Volcanizer™ is a reasonable alternative to a full Volcano hotend?

@ucirello

Жыл бұрын

Seems legit!

@GilesBathgate

Жыл бұрын

Looks like you could also use a modified heater block with two heater cartridges, and use the same nozzle for high flow and low-oose depending on whether both heaters or just the lower one is powered? (Although maybe it would mean the heat break is higher than optimal)

@ChamaraMokai

Жыл бұрын

i think it's a good alternative to the full volcano. I am wondering what the tool is called/where did you get the tool for holding the block to help install/remove the hotend at 6:30-6:35 in the video?

@gabethemodder778

Жыл бұрын

No, the cheapest option I found for the nut was $20 or more. For less than that I can get the brass nuts or even get a volcano block. If the nut was cheaper, I would heavily consider it.

@SjengdeKameel

Жыл бұрын

I've literally been using a mod like this on my CR10s5 for ages now. With a titanium outer shell and a brass internal lining press fit into the titanium. It works perfectly. I used a full brass set-up, but that lost too much heat.

Manufacturers: To get the best flow rate, you'll need a new hotend from us. Stefan: I get plenty of flow with these nuts!

@mckidney1

Жыл бұрын

He has the nuts to speak up!

@Kalvinjj

Жыл бұрын

I get it being correct and thus timeless and all but still a missed chance at writing it as "deez nuts"

@LadyTea

Жыл бұрын

@@Kalvinjj Deez nuts give you superior performance.

@tankmlee

Жыл бұрын

@@Kalvinjj Stefan: check out my new hotend idea, I call it deez Manufacturers: I've never heard of that method, what is deez Stefan: Deez Nutz

@valian8985

Жыл бұрын

enough nuts can solve every problems

Best cooking show on tv

@CNCKitchen

Жыл бұрын

Thanks 🍔

keeping track of this amount of data and then presenting it in a video like this is incredible. Great work Stefan!

@CNCKitchen

Жыл бұрын

For this one it was really tough tbh. I hope I still was able to bring along the main points.

@legalmechman

Жыл бұрын

@@CNCKitchen for even a newbie like me, you do an excellent job explaining the data and real world uses! Thank you so much for all you do!!!

@andreyansimov5442

2 ай бұрын

He is just a scientist.

Even if it only performed as well as the stock nozzle, it's good to know i can at least use a volcano nozzle to get enough clearance to experiment with stuff like nonplanar and sequential printing, which would be great for a few projects i'm working on.

@CNCKitchen

Жыл бұрын

Great point! Removing the hex might make it even better usable for this application.

@livewiya

Жыл бұрын

I was also thinking about how it allows you to increase the gantry height in your slicer settings, allowing you to print slightly taller items 'one at a time' instead of 'all at once' when printing multiple items.

I don’t even own a 3D printer but I’ve followed your channel for a couple years. I just get excited to see new videos because your testing methodology, data analysis, and engineering is top notch.

@CNCKitchen

Жыл бұрын

Awesome! Thank you! Appreciate it.

@brianmi40

Жыл бұрын

At $69 delivered for a Ender 2 Pro off ebay as an "unrepair" (a customer return, mine had never even been assembled), what's holding you back? Ender 3 pro's are $79 delivered, same unrepair customer returns...

@eccomi21

Жыл бұрын

@@brianmi40 maybe he just does not have the usecase. if you do not tinker a lot or are not interested in novelty or minifigure prints, affordability/availability does not matter.

@brianmi40

Жыл бұрын

@@eccomi21 for sure, was just informing that Covid has led to all time best deals on printers…

@SianaGearz

2 ай бұрын

@@eccomi21 But with a 3D printer you always have something to tinker on: the 3D printer itself, especially if it's cheap, a little flawed, and not locked down against modifications. It's an ideal hobby.

I love how you are like "look at all the awesome stuff others are doing" ...... "Lemme show you how to do it on the cheap but still quality" You are very appreciated good sir!

I've squeezed a bit more performance from my DIY "volcanoid" solid copper hotend by adding high temperature thermal paste (400 °C stable) to fill the air gap in the threads. (Don't use regular thermal paste)

@TechGorilla1987

Жыл бұрын

I see what you did there. :D

@aurimasknieza7320

Жыл бұрын

Would automotive copper grease do well in such application?

@mckidney1

Жыл бұрын

@@aurimasknieza7320 no it serves the opposite effect. But do not worry your printer is nowhere near such sensitivity that paste will be needed. Such a printer would require Slicer to adjust PID settings based on flow rate.

@cutterboard4144

Жыл бұрын

what is the high temperature paste made of?

@suromark

Жыл бұрын

@@cutterboard4144 I searched for thermal paste that's made for high temperature sensor mounts (exhausts, heater etc.), found a company that sells 5 gram syringes of that stuff. It's labelled "TG 20031" though that might just be that company's product ID and not a general term.

Use a piece of silicone tubing to insulate the exposed nozzle threads.

@CNCKitchen

Жыл бұрын

Good point.

Just had a great idea: Simply buy some 6 or 7mm ID silicone tubing, slide it over the exposed volcano nozzle, and cut to length. Or buy 10mm or whatever is necessary to slide around the nuts. Super simple insulation against the cooling fans that's cheap and easy to remove.

I'd love to see this tested with the newer CHT volcano nozzel

@coced

Жыл бұрын

Yes is it that new ? i can't find any review of it !

@cozmo4694

Жыл бұрын

@@coced I only saw it recently while looking for a hotend for my SR, with no reviews

@ianbruene1529

Жыл бұрын

CHT Volcano nozzle on a Dragon HF. "How much flow can you get?" "Yes."

@powerstroke01

Жыл бұрын

Im tempted to buy a few. They seem interesting.

@JamesElise160

Жыл бұрын

I have a volcano cht on my voron, the performance difference over the standard volcano I had before is significant

Stefan, your suggestions worked perfectly for me. I used a Volcano long nozzle on my Ender 3V2 with 2 brass nuts to lock against the hotend block. After adjusting the Creality touch sensor and re-setting the Z-offset, it printed my test square perfectly. I've not made any redirect for the cooling air so it might require a little re-direction so that the air is pointing to the nozzle tip (as standard) and not on the extension. Next step is to turn up a bit of brass and make a silicone sleeve to optimise heating. It was always a pain to visulaize the printng process, now I can see the extruder perfectly on very small prints. Thankyou!

Just saw the insert soldering tips. Those things are bangers, especially since they advertise M900 compatibility which previous tips I've seen don't seem to cover due to incorrect lengths which I've seen others say burns out ceramic heaters. Basically an instant buy. I can't believe no one has made this product given how relatively simple it is. It doesn't even have the type of price premium I'd have expected.

Dude, that’s nuts!

@andreyansimov5442

2 ай бұрын

😂

For hotend heat isolation I use teflontape for water pipe sealing. Cheap and common. Result is amazing.

When I saw the thumbnail I thought oh geez. But like always you backed it up with data and showed your work. Great job. This opens up a ton of options for printers that lack the ability to easily replace heater blocks. I'll def give this a go.

@CNCKitchen

Жыл бұрын

Doing my to show what work or not. Have fun playing around with the idea.

Cool, did pretty much exactly that and got +60% more flow. P.S. With hardened steel volcano nozzle there much less of an effect w/o a brass nut, which makes sense.

@CNCKitchen

Жыл бұрын

Good job!

@djddm8760

Жыл бұрын

​@@CNCKitchen could you explain how to adapt the z probe for auto bed leveling and z homing when making the nozzle longer?

This is going to change how hot ends and nozzles are designed. Great work, Stefan.

Always love a bit of data challenging preconceptions. To me this raises an interesting option with non-planar 3d printing if it ever takes off. If you need more clearance from your print head assembly to get the angles you want just use the volcano nozzle and nut method.

Your data and testing are second to none. Thank you Stefan

High-flow hot-end manufacturers: "Aww nuts!"

This video saved my qidi tech x plus from getting dumped, bless you kind sir.

Volcano : you need us for high flow rate Cnc kitchen: you're nuts

I always wondered about using a v6 nozzle in a mk8 heat block because they stick out so far. Great video and info!!

This is a great experiment, and the results are very surprising, I was thinking of changing the hotend on one of my printer to a volcano, but if you can get similar, if not the same, results by just plugging in a volcano nozzle, maybe I don't need the volcano hotend after all, thanks Stefan!

This is an incredible amount of testing and the data is displayed clearly. Very nice work, thanks for experimenting and sharing your results!

I went to the hardware store today and picked up a handful of 6mm x 1.0 nuts. I filed the contact surfaces of a single nut flat, screwed it onto a 0.6mm volcano nozzle, and mounted it on my standard E3D hotend and heater block. The results have been amazing! I have been able to push my delta printer to 120 mm/sec speeds without any flow problems. I'm sure I can probably go faster, but considering that your method has already allowed me to go from reliably printing at about 70 mm/sec to 120, I am super happy! Thank you for the great video and for all of your careful research on this subject.

Nice job on the lead free brass inserts. Was looking for those and couldn't find them anywhere

@CNCKitchen

Жыл бұрын

We're happy that we decided to go that route. Great that you like them.

Stefan:”you know what increases flow rate?” Manufacturers:”our new ho-“ Stefan:”DEEZ NUTS”

I love nuts! Wait...

@Piction3D

Жыл бұрын

hold on

@WhenDoesTheVideoActuallyStart

Жыл бұрын

I love nuts!

Wow great data. Thank you for all the tests and making the great presentation

Thanks to your video I change regular mk8 0.6 type nozzle to volcano(fake one) 0.6 nozzle with two steel nuts. It's insane that i went from max 12mm³/sec to near 25mm³/sec and above this values filament forms in something like spring under extruder toothwheel ! Thank You - its working brillant !

I encourage you to continue your well-done videos. Always packed with information on 3d printing.

@CNCKitchen

Жыл бұрын

Thanks, will do!

5:30 I found your video researching whether I should cut my nozzles to prevent them from protruding from the heater block! :D

Your latest videos are just mind-blowing!

@CNCKitchen

Жыл бұрын

Appreciate it!

Excellent work Stefan.

Awesome! Would love to see how this works with 0.6 and 0.8mm nozzles

You are a Saint. Sharing experienced practical knowledge. I see it brings you and others joy. Very inspiring. Now off to wrap some copper (16ga house) wire around some nozzles and twist it snug with pliers. Inspiring indeed : )

Very great deep dive investigation once again - just what one expects when stepping into the @CNC Kitchen ;-)

I did the Volcanizer mod on my printer with a 0.6mm nozzle on a Ender 3 v2. Works great and shaved so many hours off my prints and still looks great. I used a m6 steel nut and spacers with thermal compound between each for isolation of the brass nozzle. I mostly print functional bigger parts and for my application great mod!

Fantastic video, and really interesting research and results!

I rely on your videos to print faster and better, this information is extremely helpful, thank you

Thankyou. Always great to see ways to increase performance.

Funny you made this video. I put a new hotend on my Vyper and the nozzle sat to high where the z end stops would hit before the nozzle hit the bed. So I put a volcano hot end in and it worked good. Very nice video.

Super"volcanoiser" would be cool- only problem being its a really long" lever" if it snags on a print

Thank you very much for your revealed experiment and lots of testing and I learned a lot from your interesting & wonderful videos.

Cool… Wonderful test! Thanks, Stefan!!!

Nice to see the CHT nozzles hold their own. I should probably get around to installing mine... Been sitting there for months.

Would love how a volcano nozzle with a diy vulcanizer and CHT mod would perform. Thank you for the video, really appreciated!

Thank you for creating these videos! What digital caliper do you use?

i very much appreciate your detailed scientific approach to anything you test. great video and interesting results!

@CNCKitchen

Жыл бұрын

Thank you!

Super fascinating! What a simple concept with impressive results.

Wow! Again just awesome and massively helping me!

I just installed a volcano nozzle on an original CR10, I added also klipper with RPI, bl-touch and locked the bed with nuts. Let me tell you that the best improvement on quality and speed came out after using the Volcano. I cannot believe how good are the prints now, and so fast....

This video addresses a question I asked myself not even a week ago. I gave up on finding out the difference between the Rapido hotends and thought I'd never get a satisfying answer. Thank you for proving me wrong. Fascinating!

@CNCKitchen

Жыл бұрын

Happy to hear that! You probably wasn't the only one curious about the inner workings.

This is incredible, thank you!

Great content as usual. Thanks. I recently covered my soldering iron to prevent my fingers getting burned by the long exposed heating section (cheap soldering iron). I used car exhaust tape, basically glass tape with some high temperature adhesive impregnated. The adhesive becomes like glass when heated and the hot part is well insulated, or better at least. The tape wrapped around my soldering iron now gives me more warning and time to yank my fingers away. I would think that high temperature fibre glass tape as used in stoves and other heating element wiring would nicely slip over the long nozzle and reduce cooling from the fan

Super interesting video. That was a ton of research and documentation. Mahalo for sharing! : )

I have had such a hard time finding good heat set inserts, this is perfect timing!

This is my favorite 3d printing channel because of practical, scientific info like this. Thanks for sharing!

@CNCKitchen

Жыл бұрын

Glad you enjoy it!

Nice to see this tests. I have had such a setup a long time ago but never really tested its performance (yet) but found the replacing of standard nozzle with vulcano worked well except for the loss of Z-hight. So after a while it was replaced again with a standard nozzle on that printer. I had planned to replace one of my printers with a vulcano - with your real testresults in mind I will probably just replace the nozzle now. Thanks!

LOL - the Phaetus Rapido UHF does this and it works wonderfully! Edit: Aaaaaand I'm an idiot - that's where you got the idea from!

Wow, this is nuts! :D

Fascinating. Amazing job Stefan.

great video as always 👍 impressive test thanks for sharing your expirences with All of us 👍😃

This is pretty cool and valuable information. Thank you for doing all this crazy stuff and keeping us well informed. o7

Thanks for once again being top tier with both your methodology and frontier thinking. You’re as always impressively thorough. So; while these tricks can be great for simply increasing the max flow rate drastically, the long melt zone will also cause more oozing and hence, a loss of detail and a severe risk of extensive stringing. To strike a good balance seems easiest doable by using a Bondtech CHT nozzle which I use today. As the cheap Chinese knock-offs are not made with chamfered sinked holes like the original Bondtech CHT, they cannot be recommended for anyone wondering if this is a viable economical shortcut. But to be fair, it is possible to actually do this yourself if you have the tools for it.

Thanks for the content, I always enjoy your investigations and findings 😁

@CNCKitchen

Жыл бұрын

Thanks! Appreciate it!

Another great one Stefan. Thank you.

Awsome video as always! Would be could if you could also compare the flow gain with copper plated heatblock and nozzle

Awesome findings Stefan!! Now hear me out, I have an idea for a quick follow up. Use one of your modified volcano nozzles you made for the DIY CRT nozzle video and use it with the brass nuts. The ones with the copper wire inserted in it. Those results could be even higher and it would be cheap to make a really high flow nozzle.

Well done Sir. Well done!

I think its time to test 0.6mm nozzles!!! I'm all in for this testing!!!

I've been running exactly this setup for a while now, didn't have any issues with it even at high flow rates (20+mm3/s) Only problem I had is that a strong part cooling fan can mess with sensitive thermal runaway protection in Klipper. Relaxing settings a bit there helps though.

Excellent job, thanks!

Two days ago I was faced with blocked nozzle on my ender 3 pro and did not have any more spare nozzles, hence I used a more commonly available nozzle as it has the same thread but longer. So I reduced the threads in the heartbreak and used that to compensate for accommodating the workaround nozzle and interestingly I got the same perfect print resolution and finish. Very same concept to what you have explained. I totally agree with you on this concept

What amazing testing! As always you shine a light on things too many of us take for granted, and back it all up with scientific method, thanks!

@CNCKitchen

Жыл бұрын

Thank you! Mutant helps me here as well 😉

Inspired by this video, I did another variation of this. Screwed the volcano nozzle completely through my Ender 3 V2 (MK8) hotend, then a long (about 10 mm) M6 nut to couple the nozzle to my bi-metal heatbreak :)

Great video! What was the V6 holding tool you briefly used?

Volcano lawyers: “Please stand by for a comprehensive message explaining our concerns”

Why did i just recently buy the e3d revo Mini again? Danke für dieses wiedermal beeindruckendes Video! Wer hätte das gedacht...

excellent testing stephan!

Great video. Thanks!

Point definitely proven! Very cool numbers Stefan! Great thoughts, easy to understand and digest too. Nice work!

@CNCKitchen

Жыл бұрын

Much appreciated! Happy to hear that the massive amount of data was somehow understandable.

The best thermo-conductive material to use for the block would be pure copper but that would create a problem trying to move a heavy chunk of material around. The latest "next gen" machine designs are able to move a lot faster with a lot more control and stability than say ever 5 years ago, so even while swinging around significantly heavier extruders and their steppers so maybe they will be able to keep the mass of a copper setup under control??? Copper would also act as a bigger "heat reservoir" which would speed up the local transfer of heat to the nozzle melt chamber when new plastic removes the heat by absorbing it. This could very well reduce the time to melt the filament. As above, aluminium nuts would perform better than steel ones as far as mass moving around is concerned. Also, apply thermal paste (like that used on computer CPU's) to the faces of the nuts and block to help the transfer of heat from the block into the nuts. Modern high performance car engines with big turbo's use a ceramic coating on the exhaust pipes to help lower the amount of heat that is radiated from the exhaust pipe so why not ceramic coat the heater block and nuts? As far as I see it, the problem is getting enough heat to the area that is the melt chamber fast enough so that the filament is able to melt without causing too much heat gradient in the thermal heater block around the area that is adjacent to the melt zone. Come on Stefan, FIGURE IT OUT !!!

Haha - and I thought the cheap mellow branded nut thing I bought on aliexpress was a joke. I guess I better take it seriously now! 😂

@CNCKitchen

Жыл бұрын

Seems to be working. I wouldn't have expected it to be so efficient.

I lover your research!

This is pretty genius. I recently went full volcano on all my machines last winter

Hypothesis: There may not be very much of a heat gradient. Yes there will be a drop off in heat towards the nozzle because it's farther away from the heater. However, the filament is coming from above and closer to the heater. With the filament moving the temperature might be a lot more balanced throughout.

@CNCKitchen

Жыл бұрын

Indeed. And it might even carry some heat with it. I need to simulate that at some point.

@hate-conductor

11 ай бұрын

This is not true. I did as he said. The printer does not print at the same temperature because the hotend is too cold. I managed to get it to print at a temperature of 10 degrees above normal. Only in this case it is completely incomprehensible what was the point of fencing all these crutches, if you could just raise the temperature.

@VagabondTE

11 ай бұрын

@@hate-conductor You're misunderstanding the experiment. He wasn't printing. He was running flow tests. He keeps the temperature the same throughout the video in order to find and measure the difference between the methods. If you tried one of these methods then, yes, you may need to increase the temperature to get consistent prints again. However, since you didn't say anything about flow or print speed it doesn't make any sense to call these methods "crutches". You might be able to print at a higher speed and not realize it. Or it might not work because of your machine and setup. None of this is a guarantee. Also nothing you've said disproves or even addresses my hypothesis. Nothing here at all measures heat drop off.

@MuhammadRFabio

8 ай бұрын

​@@VagabondTE i have tried this method with 0.6mm, 0.8mm. and even 1mm nozzle size and it rarely prints well, clogging seems to be an issue, increasing the temperature exacerbate the problem, I use both brass nut and regular nut and both produce similar results, I gave up using this method and go back to regular nozzle

@VagabondTE

8 ай бұрын

@@MuhammadRFabio What method? I didn't suggest any method.

The virgin Volcano vs the Chad VOLCANIZER™️

Can´t wait to see the ultra nozzle (long nozzle in volcano with extra heat conduction bars inside and so on)? Great work again!

Great job as always

This is awesome. Im sure somebody has done this previously in the past, but i love seeing people experiment with their printers now adays, even with such a saturated market for all sorts of proprietary accessories and upgrades for 3d printers.

Love the less toxic products!

@CNCKitchen

Жыл бұрын

Thanks, we're happy that we decided to go that route.

first the cr-10 upgraded with volcano heatblock, then the diy cht nozzles, and now volcanizer. i know volcano heatblocks and nozzles are already cheap nowadays, but man the accessibility of your solutions and mods are just an armlength away, and you've got the data to prove it! also, tom's video on the 0.6 nozzle makes a lot of sense too. i wish there were more stefans and toms in the community. keep the reprap spirit alive!

Great video. Thanks

Great work!

That's just nuts!

I love your work Stefan! I recently bought a Rapido UHF and was surprised to learn that for the extra price you pay you get basically…a nut (plus a volcano nozzle).

@CentaXBerlin2

Жыл бұрын

and the 2nd silicone sock. HF and UHF version did cost exactly the same at the store I ordered. With the HF version you receive an extra hardened steel nozzle instead of the UHF stuff.

@itayst

Жыл бұрын

@@CentaXBerlin2 oh right the long sock.. I guess a hardened nozzle would be a better choice for me, if I had the chance to choose that (ordered from AE a while ago)

I want to see more advancement in hot ends. Things like the Revo that wrap the cartridge around the nozzle, and other novel experiments. It's so frustrating trying to adjust a traditional hot end