Mobil 1 Stand was cool. Icing on the cake was the surprise under those tins. Nice find!

@HardCoreFab

8 ай бұрын

Yes it was!

I would back light the Pepsi signs with LEDs. That’s would be cool.

Awesome finds! That stove is totally cool! Restore and put it in your office !✊😁

@HardCoreFab

8 ай бұрын

That could happen

@ThatRustLife

8 ай бұрын

That's exactly what I said!

Old woodburner/coal stove would be awesome in the lounge room

@HardCoreFab

8 ай бұрын

That it would!

Love the Pepsi sign and it is great that yall are fixing up the old place

I think I would have to try a rustoration on the bad Pepsi. A good painter could "fauxtina" it. love the Mobiloil gargoyle

That sign was cool. Good pick.

@HardCoreFab

8 ай бұрын

Thanks, I'm enjoying it

@treyjohns4254

12 күн бұрын

There is a product called prep n etch that can take the rust off the bottle cap.

Hey Anthony, We knew you had some good stuff when you went pickin that old place. I think keeping the first Pepsi as it would be best for it. But the badly faded sign is begging for a repaint. I bet your painter friend can do an amazing job on that one. The Mobiloil sign would have been the top prize had it not been so shot up. Being you have the same sign on the back you might get your painter friend to paint the back side to show what it was like in good shape. You may be surprised at the heat that stove puts out. It does look to be a coal stove but it will burn wood. That power hammer is the piece I am looking forward to seeing cleaned up and working. The echo was not bad in this video. Still there but nowhere near as bad as it used to be. Are you going to do anything with the IH van body that was at the place ? Good haul, good video. Work Safe, Be Well Enjoy Life

@williambruce9207

8 ай бұрын

Stuff does look good. A nice haul. I almost had a Pepsi sign like yours, but the old barn it was on fell down, then the owner sold the property. I have not talked to the new owner yet. But it has been a few years now. I did dig out of another persons field 2 round Texaco signs. Only one had stuck up out of the ground for years and people lifted a edge and bent it up. I finally got permission to dig up the sign from the widow of the farmer. So I went with my bro in law and 2 shovels, and we found 2 Texaco signs buried, with the totally buried one in much better shape, just like yours. Now I know what to use to clean them before I hang them. Those old Phillips 66 oil cans would be nice to display too.

Congratulations audio is so much better! 😊

THANK YOU

I’ve had a lot of success with a product called Prep N Etch. It takes the rust off of tin signs. Especially the bottle cap area of the Pepsi sign.

@HardCoreFab

11 күн бұрын

I'll have to play with some of that and see how it goes

@treyjohns4254

11 күн бұрын

Put it in a spray bottle and apply it. Use a regular dish sponge 🧽 with the course side rub it in and let sit for 15 minutes. Repeat that every 15 minutes until it’s all the rust is off.

@treyjohns4254

11 күн бұрын

kzread.info/dash/bejne/eIWHxLmEgKWWm9I.htmlsi=WFb5t2htVUj1N_Ov this is a guy using it. He cleans signs all the time with it.

@treyjohns4254

9 күн бұрын

kzread.info/dash/bejne/eIWHxLmEgKWWm9I.htmlsi=_Cma3ivL8S9BFIyg

We had one of those old push type reel mowers when I was a kid. It took both my brother and I to push it. My dad ended up sticking a gas motor on top of it. That just made it terrifying! My grandpa had a welding and machine shop where he also had a portable disk rolling operation. It was.cool.I sharpened lots of plows with it. He also had one of the trip hammers, but it was over 8 feet tall. Those are great finds!

Nice finds 👍

Awesome finds! Love your channel 👍

@HardCoreFab

8 ай бұрын

Thanks man!

That tin would make a cool headlinr

@HardCoreFab

8 ай бұрын

I like the way you think!

The signs turned out nice.

Very cool stuff. Would love to see more on the bender. I just picked one up over the summer. Mike c

@HardCoreFab

8 ай бұрын

I may do some with it at some point. I have to much on my plate to say when at this point.

@thercbarn5001

8 ай бұрын

@HardCoreFab yeah I get it. I got a manual with mine. Just gonna have to play with it. When I have time lol. On my project I need to bend some square tubing into a arch. For front fender attachment points. And some radius for my trans tunnel.

Its resses penutbutter cup

is that the number 2 bender ( the small version) ?

@HardCoreFab

8 ай бұрын

yes

What the heck special chemical do you use?