Write in a comment what car and engine you have, as a community we will be able to help each other 😀🤩

you are a legend :D subscribed :)

Very useful video. But it wouldn't be bad to add an option in which the factory settings are returned, in case of a possible error.

Amazing !!!

What a great video for VCDs I have a 2013 Golf TSI, they changed the headlight bulbs or bulbs in the high low, quarter and fog lights with LED bulbs and then the yellow warning light comes on in the cluster like (bulb burned out), how can you change the bulb or bulb option? bulbs to LED and turn off the blown bulb warning light? I hope you can help me, I will greatly appreciate it. Thanks greetings-

👍

Is it possible to change dial speed from mph to kph virtual cockpit 2020 gte

Hello. Do you know how to change the starting temperature for webasto heating. Origin is starting at 3° and below. Aux webasto heating. I would like to change this temperature. Thank you

@CheckEnginePlusMinus

16 күн бұрын

Meaby try this : 1. Open VCDS and select “Select Control Module”. 2. Navigate to “08-Auto HVAC” or the specific module for auxiliary heating. 3. Click on “Adaptation - 10”. 4. Search for the adaptation channel that controls the activation temperature for the Webasto heating system. This might be labeled something like “Temperature threshold for auxiliary heater” or similar. 5. Change the adaptation value to the desired temperature. For instance, if the default setting is 3°C, change it to a higher value like 5°C or as needed. 6. Save the new setting and exit the adaptation menu. 7. Conduct a full system scan to ensure no errors have occurred due to the changes. 8. Test the system to make sure the Webasto heater now activates at the new set temperature.

I need help with my vw Amarok 2019 trendline, my high beams are not working, I was trying to enable some nice tweaks but I think the high beams got changed and know the winks are not working, where should I got to program de code again and came back working again. The bulb is h15

@MoorGnosticism

Ай бұрын

Make sure the car is on level ground and that the suspension is settled Procedure 1 1. Select Xenon range control module @ address hex55 2. Select Basic Settings 3. Select Basic headlamp setting and start the procedure 4. This is where you would adjust the headlights using their manual adjusting screws as referenced against a suitable aiming target - but in your case go to the next step Wait a period of time (suggest 3 seconds) - then stop the procedure 1. Procedure 2 (still in Basic settings in hex55 module) 2. Select Acknowledge basic setting and start the procedure 3. The reference settings from Procedure 1 above should now be "recorded" in the module Wait a period of time (suggest 3 seconds)- then stop the procedure Back-out of the module, clear any error codes and exit the software (don't forget to disconnect the dongle)

I have VW Scirocco MK3 2011, how could I deactivate the 3rd tail light which was performing both tail light & brake light? The point is I bought the LED strobe light, which I'd to replace existing halogen one. After replacing the strobe brake light works fine, but then tail light is on, the strobe brake light is flickering... I do not know how to put some load resistance in, so I thought if I could deactivate the tail light function while brake light is still active, it would serve my need..

@CheckEnginePlusMinus

17 күн бұрын

To resolve the issue with the third tail light and strobe brake light on your VW Scirocco MK3 2011, you can use VCDS (VAG-COM Diagnostic System) for coding. Here is a step-by-step guide: 1. Connect VCDS to your car: • Plug the VCDS cable into the OBD-II port of your car. • Connect the other end of the cable to your laptop. 2. Open VCDS Software: • Launch the VCDS software on your laptop. 3. Access the Central Electronics Module: • Select “Select Control Module.” • Choose “09-Cent. Elect.” 4. Adaptation Settings: • Click on “Adaptation - 10.” • Search for the adaptation channel related to the tail light function. It might be listed as “Leuchte23SL HLC10” or similar, depending on your car’s specific setup. 5. Deactivate Tail Light Function: • Find the setting for the tail light function (look for something like “Light Function A” or “Light Function B”). • Change the value to “not active” or a similar setting that indicates the function is deactivated. 6. Save the Changes: • Click “Do It!” to save the changes.

@prinyaw

17 күн бұрын

@@CheckEnginePlusMinus Many thanks.. I will try tomorrow

Do you know how to adjust Matrix headlights of a Passat B8 2022

@MoorGnosticism

Ай бұрын

Make sure the car is on level ground and that the suspension is settled Procedure 1 1. Select Xenon range control module @ address hex55 2. Select Basic Settings 3. Select Basic headlamp setting and start the procedure 4. This is where you would adjust the headlights using their manual adjusting screws as referenced against a suitable aiming target - but in your case go to the next step Wait a period of time (suggest 3 seconds) - then stop the procedure 1. Procedure 2 (still in Basic settings in hex55 module) 2. Select Acknowledge basic setting and start the procedure 3. The reference settings from Procedure 1 above should now be "recorded" in the module Wait a period of time (suggest 3 seconds)- then stop the procedure Back-out of the module, clear any error codes and exit the software (don't forget to disconnect the dongle)

😁😁😁

@CheckEnginePlusMinus

7 ай бұрын

✌️

Hello. Does anyone know how to code for the AUDI Q5 FY-2017, with an electric trunk. I would like to close it both from the remote control and from the car from the button next to the driver on the door, to close the trunk. I can only do it now open and close only from the button on the trunk. Thank you

@rizzla664

4 ай бұрын

Go to Controller 6D - Trunk Electric 16 - Security Access - 10 - Adaptations Activate from drop down menu

@CheckEnginePlusMinus

16 күн бұрын

Hello, try this : Detailed steps for coding: 1. Open VCDS and select “Select Control Module”. 2. Navigate to “46-Central Convenience”. 3. Click on “Adaptation - 10”. 4. In the adaptation channels, find the settings related to the trunk operation: • Search for channels like “Comfort operation: Remote control closing” and “Comfort operation: Interior button closing”. 5. Change the value of “Comfort operation: Remote control closing” to “Active”. 6. Change the value of “Comfort operation: Interior button closing” to “Active”. 7. Save the changes and exit. 8. Run a full system scan to check for errors. 9. Test the trunk operation using the remote control and the interior button next to the driver.

@matedu4508

16 күн бұрын

@@CheckEnginePlusMinus Thank you. You manage to give me the values ​​of each IDE0.....MAS..., THIS CANNOT BE MISTAKED. I ALSO LEAVE YOU A VIDEO OF WHAT I DID

Hallo, kann mir jemand sagen, wie ich beim VW Bus T 6.1 die Start-Stop Funktion deaktivieren kann? Besten Dank und Gruß Peter

@dutchsq5181

2 ай бұрын

19 CAN-bus interface Adaptation 10 Select: 'Start_stop voltage_limit'; change that from '8.2V' to '12V'

How Audi A6C7 ?

@CheckEnginePlusMinus

16 күн бұрын

Hi, what did you want to code?

Hello can i code the taillights from us to eu after replacing them

@CheckEnginePlusMinus

8 күн бұрын

To code the taillights from US to EU after replacing them using VCDS, it depends on the specific car model you have. The process may vary, and some vehicles may require additional steps or coding adjustments. Please provide the make, model, and year of your car for more precise instructions.

@blackpuntotjet8182

8 күн бұрын

@@CheckEnginePlusMinus its an audi q3 2016

@blackpuntotjet8182

7 күн бұрын

@@CheckEnginePlusMinus audi q3 2016 any suggestions