I'm really glad you have done this video, i was considering one of these, but had nothing to go by for the Meriva B. Thanks so much! Nice detailed video too

@baconbuttties

Жыл бұрын

Thanks 👍

Smart A** 😂I just love the way you do you work bless you my good friend and thanks again for all the videos and information you have provided to us all out there cheers

@baconbuttties

Жыл бұрын

👍👍

This is awesome. I love my meriva but the stereo is the only downer. Dunno if im brave enough yet but its nice that there is options

@baconbuttties

3 ай бұрын

👍👍

Hi, super videos, this and the other with the settings! I managed to get the original radio cable with the big plug up to the display. Without that I had to extend wires! But, this is a hard job and you need a lot of patience in addition to very small hands. The microphone and a USB cable I put under the original radio and heater buttons in this small indentation, just below. There are openings large enough to route the cables without having to cut anything out. Nevertheless, they are easily accessible there. Laying the camera cable and the supply for it was another challenge, especially in the trunk lid. All the best, the device is otherwise top.

@baconbuttties

11 ай бұрын

I haven't done the rear camera as it does look like a hassle.

@TheDereinst

11 ай бұрын

@@baconbuttties We mounted the camera inside on top of the trunk lid trim. This was not my idea, but it is fantastic. A little difficult to run the cables inside the frame, but it works, even through this rubber tube between the trunk lid and the body. We took the power supply for the camera from the tail light. The glass is so dark tinted, you can hardly see them from the outside. However, the whole package is only one day in use. I'm already curious how well it holds up.

@jplayer8003

5 ай бұрын

Have you got a picture of this? I’m very bad at imagining things @@TheDereinst

@TheDereinst

5 ай бұрын

@@jplayer8003 I apologize for the delay. I had to take photos first and it's not my car. KZread does not allow photos or hyperlinks in the comments. The comment with a hyperlink is always deleted immediately. So I don't know how to send you a link. I have uploaded 3 pictures.

@TheDereinst

5 ай бұрын

@@jplayer8003 I apologize for the delay. I had to take photos first and it's not my car. I don't know how to send you.

Great video, please keep us updated. I have searched many time for something like this, but was always searching for 2din. This is a great solution. There are no extra's to purchase for the tire pressure and parking sensor? Is it a menu setting?

@baconbuttties

Жыл бұрын

If your car has tyre sensor and parking sensors then it works and you don't have to buy extras.

Cracking work as always @baconbutties

@baconbuttties

Жыл бұрын

👍👍

Any updates for a fix on the red door light fault? I cant buy one until this is resolved my ocd is holding me back from purchasing

Thank you for your video, my question is, for car settings like automatically turning on the air conditioning or adjusting the signal sound, I do these through the Config button on CD 300. If I install this CarPlay, where will I adjust these settings? My car is a 2011 Opel Meriva B with CD 300 installed.

@baconbuttties

11 ай бұрын

Air-conditioned is on the normal controls. Volume button can still be used.

Hello, Thank you very much for your video. I have some questions, hope you can help. - Where is the connector for cooling fan? I connected it to blue one which comes from the same place as Audio In/Out, Aux In, etc… but I’m not sure it’s correct as I don’t see the fan rotates. - I don’t see the wire for reverse camera, only for Key1, Key2 and Ant. Do we need to cut a wire for this purpose ? Thank you again.

@baconbuttties

5 ай бұрын

Mine had a connector for the cooling fan, if you haven't got one then connect it to an ignition live. You only want the fan to work with ignition on. The reverse camera also needs an igniton live

@jplayer8003

4 ай бұрын

@@baconbuttties Hello! Im having the same issue as above, where to connect the cooling fan? The wire is so short! And I can’t see any ignition to connect it to, like, where, down to the power harness? Again, the wire is so short, I’m stumped 🤔

@baconbuttties Hi man, thank you very much for the video. What minimum specs do you recommend for the android head unit, like 4 core cpu and 4gb ram? For the installation part, did you have to put the original stereo back in or can we remove it completely?

@baconbuttties

11 ай бұрын

I would go for 8 core 4gb and I removed the original stereo completely.

@burguesco

11 ай бұрын

@@baconbuttties Thank you for your quick response, keep up the good work.

@baconbuttties

11 ай бұрын

@@burguesco 👍👍

Did you use a specific kit for extending the wires?

@baconbuttties

Жыл бұрын

I extended the wires myself using what I had laying around. I have all the tools for factory type crimping.

Can I ask you one strange questions? I recently bought a meriva B (here its an opel) and the aux connector is missing. I went into the hole with a scope to see of the cable is there but I couldnt find it. I dont think it was never there so there must be a cable somewhere id say. Are you able to tell me where the cable for the aux module next to the 12 volt cigarette lighter is connected too? Id say it would go from the aux module directly to the radio but in your video i cant quite see. Anyway, great video ^^

@baconbuttties

10 ай бұрын

I think the aux cable goes back to the big main stereo connector block

@Jelpronir

10 ай бұрын

​@@baconbutttiesthank you, guess ill just have to take it out then

Hi, did you tried installing additional apps like netflix or spotify ? Does it have google store? Can you make a second video showing Android version and spec of the unit.

@baconbuttties

Жыл бұрын

I installed a dab + app. I did have a bit of trouble signing in to my Google account.

Can I ask you two things? I also bought the car radio, but it doesn't read me either the steering wheel controls or the buttons on the CD 300 Could you tell me if the code for the Canbus Decoder BOX is something like GM-09 (mine is RZ-GM09). Also how did you connect the CD-300 button box directly to the cable coming from inside or via that adapter bypassing the socket on the CD-300

@baconbuttties

5 ай бұрын

I plugged all the original CD 300 cables back in . I don't know the code as I don't have it anymore

hello, great review and information, I wonder, does the original factory fitted 'Aux in' USB still work?

@baconbuttties

11 ай бұрын

No it doesn't work

@user-gc1fk7lw9v

11 ай бұрын

OK thanks for the reply, so are the USB leads with the unit long enough to go into the glovebox so as to offer a point to plug things in, or will i need an extension lead. Many thanks@@baconbuttties

Very, very, very interesting and exciting videos which will perhaps encourage me to install a navigation system worthy of the name on my 2013 Opel Meriva B (I'm French)! I have a version of the Meriva without a camera or reversing sensor. So, before giving in, I have a few questions: the link provided in your post refers to a large number of possible versions from Ali (and I'm not even talking about the other models offered). How can you be sure you have a 100% Meriva B version? And do you know what the titles ranging from “2G+32G” to “8G+256G” and “4G+WIFI” mean? Thank you and congratulations for these videos!

@baconbuttties

8 ай бұрын

The link should all be for Meriva B 2g+32gb means 2Gb Ram 32Gb of storage.

Hi! I've a Little question: The support is included in The kit or is sold separately? Thanks for The video, greetings!

@baconbuttties

10 ай бұрын

Support is included

That looks really good! Also have a Meriva and considering upgrading it like this. Will you report if you are satisfied with it after some time? Greetings from Germany.

@baconbuttties

Жыл бұрын

Yes will give it a test to see if it is reliable and report back 👍

@OnkelUrmel

Жыл бұрын

@@baconbuttties Excellent! I'm looking forward to your experiences! Have fun with the device! 😃👍

@baconbuttties

Жыл бұрын

@@OnkelUrmel 👍👍

@MrAmilburn1

10 ай бұрын

​@@baconbutttieshow is performing now?

@baconbuttties

10 ай бұрын

@@MrAmilburn1 the only issue I'm having is the rear door warning light comes on now and again

The thing up there is a sensor for the airco if you would have climat controle

@baconbuttties

Жыл бұрын

Yes I only have standard Aircon 👍

What year is your Meriva? Because your android radio is selected for 2009-2014. I have a 2016 Meriva and I wonder if it will work with my car (canbus)

@baconbuttties

2 ай бұрын

Mine was a 64 plate facelift which I think is the same as yours.

Thought about installing it in my Meriva, but decided not to do so. For now, at least. For many reasons, actually. 1. Steering wheel buttons issues. They're selling it as a HU for Meriva, but don't have button mapping of Meriva. Nice. 2. To my taste, screen is too tall. It's placed high and doesn't look organic in it's place. Wish that BMW-like wide displays were available, but they're not. 3. Have to change Navi 600 buttons panel to CD300/400 in order for it to work properly (it only supports one type of them) 4. Screen is too distanced to be conveniently used as touchscreen. 5. All the electronics are in the screen module, which is the hottest place of car's interior in summer. Not sure about absence of throttling/performance issues. Not easy to do cable routing. 6. Speaking about routing, I have a GPS antenna on top of the car (as car came with Navi 600), but I still have to use the one which comes with the unit, don't I? The same thing with the microphone for making calls. Why? 7. Dull UI/UX of these unit is a matter of taste, you can use Android Auto exclusively (but why do you ever need that 64G/4G/8cores then?), but I don't like it. So, I'll stick to my original HU, I guess. I enabled rear view camera, turned that "linear output"/"infinity audio system" option, installed Match UP7 DSP amp, Morel Tempo Ultra midbass speakers to front doors, Alpine S-S65 to rear doors and CDT Audio HD2 midtweeters in place or original tweeters, Hiby W3 as BT audio source connected via AUX, set it all up and I can say that sound is soooo much better than it was. But yeah, I still have to use phone on a holder for navigation, which is not cool.

@baconbuttties

8 ай бұрын

I managed to map my buttons, others can't replicate what I did. Number 4 on your list is the biggest issue.

@Manuellos

6 ай бұрын

@@baconbuttties and 5 If you live in south Spain.

Hello. Very detailed video but i can't see the link to the screen model you purchased... Could uou repost it in the comments?

@baconbuttties

11 ай бұрын

www.aliexpress.com/item/1005005806623211.html?spm=a2g0o.order_list.order_list_main.11.d5391802N1iP2w

Good bless you!

@baconbuttties

Жыл бұрын

👍👍

Just wondered if you have tried downloading any apps to the unit, I fancy adding DAB radio but seems it needs the app to work, I have no idea how to connect the head unit to the internet to download the app.

@baconbuttties

Жыл бұрын

I added dab+ app by downloading it ( APK ) on my pc and then copied it to usb drive. Connected usb drive to android headunit then opened it using the file explorer app that's already installed and installed it

@user-sm2909

Жыл бұрын

@@baconbuttties My order is on it's way from China now, but I suddenly remembered you showed a Canbus in your video, is that included and does it need to be connected, if so is there a cable supplied for it? thanks again for your help.

@baconbuttties

Жыл бұрын

@@user-sm2909 canbus was supplied on mine and I did connect it.

Just received the unit and already have questions. I see you used the canbus, so that is out of the way. There are two wires that with a lable 12v and buzzer, did you connect those?

@baconbuttties

Жыл бұрын

Yes I used the canbus and you also have to connect the fan. I didn't have to connect buzzer? Is it the same unit as mine or different version?

@joepmeloen1974

Жыл бұрын

@@baconbuttties I will have a look, the front looks the same 🙂But what about the 12v wire?

@joepmeloen1974

Жыл бұрын

@@baconbuttties I have send you an email with photo's

@baconbuttties

Жыл бұрын

@@joepmeloen1974 👍

Hi very useful video! where did you get that orange tool to remove the panels?

@baconbuttties

3 ай бұрын

They are just plastic pry tools, you can get them from ebay or Amazon

Hi all, I have a question please, is the screen support included on the radio? Also, should I order the other extra cable separately if I understood correctly? I don't know much about these things, but I would like to order all the pieces and try to install it.

@baconbuttties

8 ай бұрын

The screen support and adapter mount is all included. I extended my cable myself, but someone has mentioned that they ordered a longer cable from somewhere.

@Lozzio1996

8 ай бұрын

@@baconbuttties many thanks for your help and reply! I wish you a lovely weekend.

@baconbuttties

8 ай бұрын

@@Lozzio1996 👍👍

Hi, thx for the informative Video! Is the device compatible with opel meriva b 2011?

@baconbuttties

11 ай бұрын

Yes

Maybe i'm asking to many questions 😁 but could you put in the link of the DAB usb dongle you bought?

@baconbuttties

Жыл бұрын

I will have a look and post it here and in the description later 👍 Also ask as many questions as you want.

@joepmeloen1974

Жыл бұрын

@@baconbuttties Thank you very much, i appreciate it 👍

Hi. Did you have any issues with the indicators and parking sensors sound? We can’t manage to make that work since we installed this unit. Thank you

@baconbuttties

5 ай бұрын

The plug from the top dashboard display has to be plugged into the supplied Canbus box for indicator and parking sensor sound

@danielezampirolli6461

5 ай бұрын

@@baconbuttties our Canbus did not come with an entry for that top dashboard cable. We connected to another plug that fitted but still not working. Thank you for replying

@baconbuttties

5 ай бұрын

@@danielezampirolli6461 There is supposed to be a plug for the top cable. I'm sure the original display is where those sounds come form. Best to ask the seller why there is no plug for it

@jplayer8003

4 ай бұрын

Hi, did you solve your parking sensor & indicators sound issue? I am having the same issue, I can’t hear any of those sounds, however my canbus does have a wire that ends in a little black plug that goes into the old car display. So in theory everything is plugged in, and I still have no parking sensors sound, it’s so frustrating!!

Has anyone lost the sound of the indicators and hazard lights after installing this unit? How did you solve it? I know it’s not the end of the world but worried about future MOT and honestly prefer the audible reminders as reassurance that my indicators are on.

@baconbuttties

4 ай бұрын

The indicator sound was okay on mine after installation, I think somebody else had a similar problem

@aaliyev444

2 ай бұрын

Can you writräe produkt name please.?

@josephwood9460

Ай бұрын

Did you manage to match the steering wheel buttons the Android device?

Hi, can i ask you if the central locking works correctly? After fitting this new unit it only closes the rear doors! Thank you

@baconbuttties

11 ай бұрын

Mine worked correctly

@sabinobernocco4890

11 ай бұрын

@@baconbuttties Do you know if there is a setting in the system that needs to be changed to close all doors correctly?now...i'm forced to do it manually

@baconbuttties

11 ай бұрын

@@sabinobernocco4890 There are some door settings somewhere, don't ask me where though as I can't remember.

Do you need to connect the wire the goes into the old display?

@baconbuttties

6 ай бұрын

Yes

where did you connect the cables afterwards? Behind the radio or no longer installed the CD drive where did you connect the cables afterwards? Behind the radio or no longer installed the CD drive

@uysal1975

Жыл бұрын

Could you send me a link wäre you ordert the installieren kit Aliexpress?

@baconbuttties

Жыл бұрын

Connects to original wiring. CD drive is no longer installed. Link is in description

Hello, how did you power the original dashboard of the stereo? The steering wheel controls work perfectly, but those on the dashboard don't

@baconbuttties

6 ай бұрын

What was your original stereo? I just plugged all the wires back into the button panel and some of the buttons just worked.

@alexgamer4933

6 ай бұрын

@@baconbutttiesThe same stereo as his car, Meriva B 2010

@alexgamer4933

6 ай бұрын

@@baconbuttties I contacted the seller because the model of my car is not in the canbus! Do you know how you can update the canbus or do you have to change it? (The product model is a Seicane H6N)

@baconbuttties

6 ай бұрын

@@alexgamer4933 The only canbus that was close is the Astra J.. There is no Meriva B Canbus setting as far as I know

Where are the links to the those? Can't find them. Looks good. Keep us posted 👍🏿

@baconbuttties

Жыл бұрын

Oh, I forgot.... Will add them now 👍👍

Canbus settings have been updated, now I have meriva 2011 and steering wheel control buttons work as they should. But the front radio panel cd 500 buttons don't work.

@baconbuttties

5 ай бұрын

Where did you get canbus settings?

@m3ld4r10n

5 ай бұрын

What settings did you use? I’m in factory menu and there’s no config for meriva, only other opel models

@jplayer8003

4 ай бұрын

@@baconbuttties I also downloaded the Meriva B in the canbus config, however now the steering wheel controls won’t work, argh! I’m desperate for them to work, and also for my parking sensors to beep

For the benefit of those who have to install the unit in question, I can suggest passing the large original connector of the car through an opening between the central tunnel and the back of the main instrumentation (speedometer and rev counter), clearly dismantling the aforementioned instrumentation fixed to the dashboard through two screws. From there there is another opening to pass the large connector through. Well yes, the cable in question is long enough to reach behind the radio in the center of the dashboard. This avoids having to lengthen the wires that are part of the connector. It works I assure you.

@baconbuttties

10 ай бұрын

👍👍

@Jogi6

9 ай бұрын

hi what if you remove central air vents?

@raulbernaudo4130

9 ай бұрын

Purtroppo il passaggio sarebbe troppo stretto per il cablaggio e quindi non conveniente ecco il motivo per il quale sono stato costretto a smontare il cruscotto centrale (tachimetro e contagiri). Penso che la soluzione che ho adottato sia l'unica alternativa al lavoro che ha fatto il buon BaconButties.@@Jogi6

@Garraz_

22 күн бұрын

​@@raulbernaudo4130ciao Raul, avrei da chiederti una cosa, tu che sei in Italia come me, hai ordinato la medesima autoradio che viene mostrata in video? Se sì, l'hai ordinata tramite Aliexpress? Perché vorrei fare anch'io questo upgrade, sembra piuttosto facile e vorrei capire se si tratta di un prodotto funzionale o meno.

Hello, I also bought a radio similar to yours. I have some questions... What is the connector seen at minute 14:14 for? In the connector that plugs into the canbus box, there are 2 wires (black and white) with another small connector that I have no idea where it goes... The steering wheel controls do not work for me at all... Thank you

@baconbuttties

Ай бұрын

@@stefanocaudek3952 black and white wires plug into original display connector

@stefanocaudek3952

Ай бұрын

Ah... But It Is completely different... The original connector has like 6 PIN...​@@baconbuttties

Great...do you think this unit is compatible with the 2015 meriva b with cd300 radio? Thank you.

@baconbuttties

Жыл бұрын

Yes it should be because my car is a late 2014 facelift

@sabinobernocco4890

Жыл бұрын

@@baconbuttties in the link you inserted in description(aliexpress) it refers to the model 2009-2014...for the model 2011-2017 there is another car radio(10") 🤔

@baconbuttties

Жыл бұрын

@@sabinobernocco4890 there are loads of different models, all I can tell you about is the one I bought and it fits all Meriva B's

@sabinobernocco4890

Жыл бұрын

@@baconbuttties thank you! 🫡

@sabinobernocco4890

Жыл бұрын

But will the sounds of the car can be lost?for example: directional arrows ...

I have a problem - there's no power going to the main unit. The fuse for the radio (located in the footwell) had blown, and even after I replaced it, nothing happens. Is there any advice for this?

@baconbuttties

8 ай бұрын

Have you checked fuse in the unit as well

@mustakyljys

8 ай бұрын

The problem was resolved. It was that cursed too-short cable that always came loose during installation. Thanks for your video& help anyway.

which canbus option did you set?i can not find the opel canbox

@baconbuttties

8 ай бұрын

Astra J

@LinHenry-wz2mb

8 ай бұрын

thank you

Please, where do the loose cables with the inscription key 1 and key2 connect? Thank you

@baconbuttties

7 ай бұрын

1 and 2 are usually for steering wheel controls but if its canbus then they don't need to be connected

@vutran5635

5 ай бұрын

Hello, How about the ANT wire, do we need it ?

Is there a link please to where you bought the unit. How much did it cost. Thanks

@baconbuttties

5 ай бұрын

150 pounds... I'm sure there's a link somewhere, I did do another video on it as well.

I have orderd one and should arrive next month. But my brother asked me if the device needs contstant internet for the apps to work. Do you know about that?

@baconbuttties

Жыл бұрын

The apps that are on it do not need constant internet and it does have igo navigation that doesn't need an internet connection

@joepmeloen1974

Жыл бұрын

@@baconbuttties Thanks for the quick answer. I’ll keep you posted on my build.

@baconbuttties

Жыл бұрын

@@joepmeloen1974 👍👍

buongiorno. ti ringrazio per le informazioni che mi hai fornito. approfitto della tua gentilezza e simpatia per chiederti se hai collegato quel cavetto con i fili bianco e nero all'altro capo del cavo che parte dal quadro di controllo delle stereo originale. se possibile vorrei illuminare, quando si accendono i fari notturni, il quadro comandi originale dell'auto magari tramite ponte. grazie

@baconbuttties

11 ай бұрын

Il mio pannello originale si illumina ancora? ho ricollegato i fili all'originale sul pannello

@raulbernaudo4130

11 ай бұрын

@@baconbuttties ti ringrazio

for steering wheel buttons you need to check in configurations to set the correct one, I have installed one in my Meriva B 3 months ago.

@baconbuttties

Жыл бұрын

I can only find configuration for Astra J

@Davidteri1000

Жыл бұрын

@@baconbuttties that's Canbus configuration and should work for Meriva B too, please choice that. then go to apps and enter in app called (in my case) original car then go to set and go to steering wheel buttons and set the second one, not defult. it should fix volume buttons only.

@baconbuttties

Жыл бұрын

@@Davidteri1000 I don't have that app?

@trifaloialone9452

Жыл бұрын

I have the same problems with the buttons. Have you find any way to fix it?

@Davidteri1000

Жыл бұрын

@@trifaloialone9452 i got partially steering wheel buttons working

forse per avere un quadro piu' completo dovrei far presente che la mia auto e' del 2011 ed aveva uno stereo originale dvd 800. l'autoradio cinese e' del tutto simile alla tua ma non e' la stessa. ho notato che nelle ozioni del canbus non e' prevista la opel meriva b e quindi ti chiedo quale altra auto posso settare nelle opzioni che sia piu' simile alla mia. infine ho notato che nel cablaggio dell'autoradio cinese e' presente un piccolo cavo con due fili bianco e nero che probabilmente devono essere collegati al quadro comandi originale della vettura. Se sei cosi' gentile da darmi una risposta te ne saro' grato.

@baconbuttties

11 ай бұрын

Closest canbus option is Astra J

Sorry also could you tell me how long you extensions were and what unit you got what model unit please

@baconbuttties

6 ай бұрын

Mine was 8core 64gb storage 4gb ram version. I can't remember how long the extension was.

@cyrilwoolf8848

6 ай бұрын

Thank you very much for your answer

Does this come with everythink including the screen holder that goes in the original part ?

@baconbuttties

Жыл бұрын

Yes it comes with everything, all the bits I used came in the box.

@greo4638

Жыл бұрын

Alright mate did u ever get the door lock symbol on ur car my pops up sometimes it stays and sometimes it goes ? Did u ever get ur button to sync with the correct controlls?

@baconbuttties

Жыл бұрын

@@greo4638 I have the door lock button pop up, goes off when I indicate. The canbus adapter isn't set for the Meriva back doors. Also cannot get steering buttons to work correctly.

@greo4638

Жыл бұрын

@@baconbuttties ohhh right so that’s why it shows up glad it’s not just me then :) yeah my buttons seem to be al over aswell can’t seem to use the system to correct them

@greo4638

11 ай бұрын

Quick question bud I noticed u have parking sensors when ur radio is playing and u put it into reverse does the radio go off ?

Wonderful video, very good explanation of how to fit the unit and a great review of the product. I have been looking forever for a replacement to the factory unit, my stock unit is a CD-400, don't use the CD player, I think it's the same as yours? was just worried about the wiring loom. If yours is the CD-400 its obviously OK, then i'm buying the unit!! thanks again.

@baconbuttties

Жыл бұрын

👍👍

@baconbuttties

Жыл бұрын

Yes Mine is the CD400

I've got two questions for the community one I'm trying to find the indicator fuse which I've not been able to find and i brought the Android week 360 on it can anybody tell me the best place to go through the bulkhead into the front of the car if anybody can help me on that

@baconbuttties

3 ай бұрын

Did you manage to solve your issues ?

Where can I buy an ISO adapter? Please provide a link

@baconbuttties

Ай бұрын

It comes with everything you need

Hi, I've followed the link as would like one of these but it takes you to a page with about 10head units, how do I know what one you have?

@baconbuttties

9 ай бұрын

Mine is 8 core CPU 4GB ram

@user-ol2ku3he9t

8 ай бұрын

@@baconbuttties I've bought one 😁will be here in about 9 days, don't suppose you can show me what connector runs what on the back of the unit? Paul.

@baconbuttties

8 ай бұрын

@@user-ol2ku3he9t what do you mean by connector? Which one.

@user-ol2ku3he9t

8 ай бұрын

@@baconbuttties morning, On the rear of display you had the main multi plug then I think four or five whit connection blocks for accessories I think? Usb etc and maybe fan?

@baconbuttties

8 ай бұрын

@@user-ol2ku3he9t If you ask the seller they should give you a basic diagram. I cant post links on here as youtube remove them.

Hello I've just buy one like this but like you said , no book instruction. Do you know where can i find one? Thank you?

@mikaelkerlann2976

10 ай бұрын

A link?

@baconbuttties

10 ай бұрын

There is no instruction book

and could you add a reversing camera too

@baconbuttties

Жыл бұрын

Yes it has a reversing camera option

Did you buy the 4-64 model?

@baconbuttties

Жыл бұрын

It was the 8 core 4g memory 64gb storage

Is it with dab? And does it work?

@baconbuttties

Жыл бұрын

You have to order dab separately, which is about 15 pounds. Mine hasn't turned up yet so I couldn't test it .

I have problem with the steering wheel command , I think key 1 and key 2 need to be plugged,but I don't know where!

@baconbuttties

Жыл бұрын

My steering wheel buttons are all mixed up. It's supposed to work through canbus so not sure where you connect key 1/2

@misterxit

11 ай бұрын

@@baconbuttties i have the same problem, the mute work like vol+ etc , but at now I tried various options without success , I write to raise directly and I wait an answer

@PegoOfficial

7 ай бұрын

​@@misterxitHey same here any success?

May I change channel using control pannel from original opel and than fix them on original pannel too???

@baconbuttties

11 ай бұрын

I can't understand what you are saying.

@Enrico19724

11 ай бұрын

Ok sorry….where are fun control up there are button 1, 2, 3, 4, 5, 6 for memory station radio These keys run?

@baconbuttties

11 ай бұрын

@@Enrico19724 yes you can set them to 123456

@Enrico19724

11 ай бұрын

Thank you so much

@baconbuttties

11 ай бұрын

@@Enrico19724 👍👍

Le câble qui arrive sur l’ancien afficheur est il branché ??ou libre ?dans le tableau de bord, ou faut-il laisser raccorder à l’ancien afficheur et mettre l’ensemble sous le tableau de bord

@baconbuttties

2 ай бұрын

Old display wire should be plugged into new harness

@pierrebeaufils-ur8fl

2 ай бұрын

Mais où je ne vois pas l’endroit

Just tried wiring mine in. It’s got an extra plug that connects to plug where clock comes out of. It also seems to be missing a plug on the loom for the fan. Connected power from main wiring loom and extra socket. Turned ignition on and nothing happened

@baconbuttties

2 ай бұрын

The original clock display harness should be connected to the new harness. Did yours come with a canbus adapter?

@LeeWigmore

2 ай бұрын

I think so… can I email you photos of my wiring?

Did you install the camera? Is it working well? Does the camera app starts when you reverse the car? Thank you

@baconbuttties

Жыл бұрын

I haven't installed the camera but it will automatically come in when reverse is selected. My car has front and rear parking sensors and they show in the screen when reverse is selected and the rear camera shows but I haven't installed it.

Hi, I have meriva b, but cant get fabric volume knob to work, what to do?

@baconbuttties

3 ай бұрын

What factory head unit model do you have?

@Baya84

3 ай бұрын

@@baconbuttties i have dvd900

@Baya84

3 ай бұрын

@@baconbuttties i have dvd900

@Baya84

3 ай бұрын

@@baconbuttties dvd900

@Baya84

3 ай бұрын

@@baconbuttties dvd900

Good morning, is it possible to email you? I would like to exchange some information with you about my Android radio in an Opel Meriva.

@baconbuttties

11 ай бұрын

Yes, email is in the about section.

need you to buy the screen support separately? You are welcome

@baconbuttties

11 ай бұрын

Screen support is included

not able to see the link for this

@baconbuttties

Жыл бұрын

The link should be there in the description

Hi I'm just watching your video for about 5 the fifth time I just went to the link that you supplied just wondering what model number you purchased the two clips in the little caviar part that you are your fingers with default part of the plastic preiser is what that's for you slide nose Behind Those clips and prize them out the next time don't have to comment but I just want to what part of the country are you

@baconbuttties

6 ай бұрын

I'm not sure what 2 clips you mean

@cyrilwoolf8848

5 ай бұрын

It was a two clips underneath the handbrake also I'm seriously thinking in buying one of these I look to your link and is about what price did you pay for your one give me some idea what I'm I'm looking at and also did it come in front and back camera the one you got I know this is probably when you pay questions give me a better guidance thank you

so dose that mean you don't have a cd player anymore

@baconbuttties

Жыл бұрын

You don't have a cd player

@rickydowdind885

Жыл бұрын

@@baconbuttties you say in the video that because of the wiring you only put the stereo face plate on and not the cd drive back in or have I got that wrong LOL

@baconbuttties

Жыл бұрын

@@rickydowdind885 you can't put the cd player back in as the touchscreen unit has a built in amplifier and this replaces the original unit. So there would be no wiring going to the original cd unit and it wouldn't fit because of the Extra wiring in place. If CD's are your main source of music then I would just keep your CD player. I do not own any CDs as all my music is streamed or downloaded.

@rickydowdind885

Жыл бұрын

@@baconbuttties many thanks

Bonjour et merci pour la video j'ai suivi tous les étapes tel quelle,mais l'ecran ne marche pas même que le milieu de clavier (qui controle la radio ) ne s'allume pas au contraire du bas de clavier qui marche parfaitement, j'ai essayé de revenir à l'ancien afficheur mais il ne veut pas marcher lui aussi😢,est ce que tu as une solution s'il vous plaît car j'ai perdu 5 jours avec ce problème mercii.

@baconbuttties

2 ай бұрын

Vous avez peut-être grillé un fusible

buongiorno cortesemente vorrei sapere come hai collegato l'autoradio cinese al cablaggio originale della opel meriva b perche' a me non funziona il quadro comandi dello stereo originale pur avendo collegato tutti i cavi a disposizione. Se riesci a postare delle foto dei collegamenti oppure un filmato. grazie

@baconbuttties

11 ай бұрын

Only some of my control panel works. I didn't change any wires

@user-ur2uw5vx1p

5 ай бұрын

Il problema con il cd 600 di Opel è il canbus da cambiare e poi funziona tutto

@user-ur2uw5vx1p

5 ай бұрын

Devi farti dare il GM61 e risolvi

@raulbernaudo4130

5 ай бұрын

@@user-ur2uw5vx1p ciao. Scusa cos' è il gm61?

@raulbernaudo4130

5 ай бұрын

​@@user-ur2uw5vx1pSalve io non ho il cd600 ma il dvd800 originale sull:auto

Good evening A few days ago I wrote you the following request on your email with an explanatory photo attached. Would you be so kind as to answer me. Thank you: I disturb you for a clarification about the connection of the original cables of the car and the adapter supplied separately with the car radio. What I can not understand is how you connected the black and white cable that is part of the cable and that on one side with the white cable enters the canbus and the black one enters the main adapter that connects with the standard one of the car. Apparently its connection is essential otherwise its existence is not understood. As you can see from the picture, the black connector that incorporates the black and white wire has the perfect shape to connect with the original cable of the car that connects to the control panel or with another cable always original of the car that was originally connected to the monitor in the center of the dashboard. Unfortunately, in neither case do I get positive results. I add, again for logic, that if this additional cable I connect it to the original cable of the control panel in any case the latter can not be simultaneously connected to the original cable of the car and therefore can not be used. Perhaps my explanation was a bit articulate and confusing but I hope I have made myself understood. You're a smart guy. Maybe your interface cable was missing this black and white appendage? I provide you with the photo of the cable highlighting the extra cable (what you see is a test cable but completely identical to the one installed in the car). Thank you for your patience but it drives me crazy.

@baconbuttties

11 ай бұрын

My black white cable connector was plugged into the original display connection

@raulbernaudo4130

11 ай бұрын

@@baconbuttties Good morning I connected everything as you suggested but the result is always the same: the original stereo control board doesn't work. Probably the wiring of my dvd 800 of the car is different from your cd 300 and therefore the cables do not match. Thank you anyway for your diligence and goodbye. I address this appeal to those who have encountered my same problem. Thank you

@baconbuttties

11 ай бұрын

@@raulbernaudo4130 yes your system control must be different.

@adriaanvandijk

10 ай бұрын

Same problem. Did you manage to fix it?

@aleyer_s

8 ай бұрын

Sure, it's for CD300/CD400 only

Hello, i have the same unit for my meriva, but like many other, there are problems first, i need the password for the factory menue, do you have some information about this? thnaks

@baconbuttties

3 ай бұрын

The company you bought it off will give you the password as they are all slightly different

@trigunbullet

3 ай бұрын

@@baconbuttties found it on YT by myself... many of the passwords are the same

@trenox9020

2 ай бұрын

Could you provide a link? Thx!

@trigunbullet

2 ай бұрын

@@trenox9020 kzread.info/dash/bejne/k5OCyqRynM6YaKw.html

Hello, first of all Sorry for my bad english, my car is MERIVA B 2011, I need your help for

@baconbuttties

29 күн бұрын

@@alvierociccarelli9681 How can I help?

@alvierociccarelli9681

29 күн бұрын

Hi, yes I really Hope you can help me. After installing my Android radio I have a problem with the functioning of the steering wheel buttons, for example the button VOLUME - works instead the button VOLUME + doesn't work, I saw that you're very good at solving this type of problem so I really Hope you can help me, thank you in advance, Alviero 1963 from Italy

@alvierociccarelli9681

28 күн бұрын

Helloo, any news for me? Thank you in advance, Alviero 👋🏻👋🏻👋🏻

@baconbuttties

28 күн бұрын

@@alvierociccarelli9681 everyone has the same problem with steering controls as the canbus isn't correct for Meriva B

@alvierociccarelli9681

27 күн бұрын

Ok! So I suppose that I cannot solve my problem 😭

L’ancien câble afficheur à laisser libre ??

@baconbuttties

2 ай бұрын

white and black wire plug in my video connected to my old display plug

@pierrebeaufils-ur8fl

2 ай бұрын

Est-ce la fiche noir avec fil noir et bl1nc à côté de votre doigt à 14minutes 20 de l1 vidéo

@baconbuttties

2 ай бұрын

@@pierrebeaufils-ur8fl yes

@pierrebeaufils-ur8fl

2 ай бұрын

Super merci beaucoup

Has anybody having the following problem: 1. Device don't go to sleep if I pull my key out, it wait about one minute and than go to sleep? 2. I can not turn on device if my key is not in ignition state? 3. Android auto can not connect wireless, only by cable?

@baconbuttties

9 ай бұрын

Key has to be in ignition for it to work. My android auto will connect wirelessly but is intermittent.

@MarkoBabovic

9 ай бұрын

@@baconbuttties Thanks for fast reply. Does device eat battery in sleep mode?

@baconbuttties

9 ай бұрын

@@MarkoBabovic I haven't had any battery issues so far.

@Jogi6

9 ай бұрын

hi my device also doesn't turn off when I take the key out off the ignition, did you solve it?

@MarkoBabovic

9 ай бұрын

@@Jogi6 Nope, I am facing now the issue with steering wheel and panel synchronisation. The learning does not work correctly. Also forward key on the steering wheel is not detected. Do you have similar problem?

If anybody has problem with google services or apps that requires internet let me know. I had that problem and they send me new firmware so it is solved now. Also android car wireless works now.

@baconbuttties

9 ай бұрын

That's good, have you got a link to the new firmware?

@MarkoBabovic

9 ай бұрын

@@baconbuttties Yes but it is not allowed to add links here, not sure why. I will send you via email.

@baconbuttties

9 ай бұрын

@@MarkoBabovic Yes KZread removes links. Here is the email baconbuttties@gmail.com

@dodz26

8 ай бұрын

​@@baconbuttties Hello can you send me the link for the new frimware please?

Still satisfied with the purchase?

@baconbuttties

Жыл бұрын

So far yes. the only negative is its a bit far away to reach.

@joepmeloen1974

Жыл бұрын

@@baconbuttties can't that be solved with the controls on the steering wheel or have you not yet been able to find the right setting?

@baconbuttties

Жыл бұрын

@@joepmeloen1974 You can do a lot with the steering and radio controls but not everything.

@joepmeloen1974

Жыл бұрын

@@baconbuttties Could you tell me if you can change the language to dutch or the tire pressure from kpa to bar? And does the unit startup quicker then the first time?

@baconbuttties

Жыл бұрын

@@joepmeloen1974 the unit starts up almost instantly after the initial start up, will have to get back to you on the rest.

The one that's just underneath the electric brake behind the little cover

@baconbuttties

6 ай бұрын

I'm still not sure what you mean

Thanks! Will this works with a small screen from the Merva B as in this picture? media.autoweek.nl/m/m1my6m1bmbr3_800.jpg And what kind of new basefront u have for the navigation?

@baconbuttties

Жыл бұрын

I think it should work with the small screen as I think the dashboard board is the same on all models. I'm not sure what you mean about the navigation?

@MikeH26

Жыл бұрын

@@baconbutttiesI mean the holder where you put the navigation in and then mount it in your dashboard. 1:34

@baconbuttties

Жыл бұрын

@@MikeH26 It was included with the screen

@MikeH26

Жыл бұрын

@@baconbuttties ah! Super thanks!

@baconbuttties

Жыл бұрын

@@MikeH26 👍👍

Just tried wiring mine in. It’s got an extra plug that connects to plug where clock comes out of. It also seems to be missing a plug on the loom for the fan. Connected power from main wiring loom and extra socket. Turned ignition on and nothing happened

@baconbuttties

2 ай бұрын

Have you fixed it? sounds like a fuse blew...

@LeeWigmore

2 ай бұрын

@@baconbuttties it was the canbus thingy you said about before. I was a numpty and hadn’t plugged it in. Thanks!!

@baconbuttties

2 ай бұрын

@@LeeWigmore Glad it is working now 👍👍