Can you share the Schematics of the BMS and Charger so we can also have a look?

I am trying this as we speak. If it works for my flat batteries, that would be pretty crazy. Thank you!

@Razspareparts

7 күн бұрын

Let us all know... I tried on batteries with 20 volts and it worked 😊

@Razspareparts

7 күн бұрын

@@CharpuART I tried on flat batteries it shows red light and is pulling some milliamps but I didn't have the patience ☺️ ... From 20v I did and it does work ... Original settings goes green from under 35 ...so is a big improvement.... Lol

@TerryBenson_News

7 күн бұрын

I don’t know where my current voltage is right now, but I might have to leave it for a while. I can see the screen is starting to turn on-it never did before, so I hope that’s a good sign. The charger light is a solid green. ( btw im the same person as earlier comment) 5:31

@TerryBenson_News

7 күн бұрын

It went from solid green to now flashing red and green. Hopefully progress?

@TerryBenson_News

6 күн бұрын

@Razspareparts I'm not sure there is any progress. After the whole night, it is still doing the same thing, but the charger light is red. Should I just leave it to do its thing?

Het, I watch all your video’s and it help me so much thank you! Can I send you a donation? I have 3 S3 batteries with blown fuze I have ordererd a heat gun and going to try next week if I can fix the batteries my self

@Razspareparts

8 күн бұрын

I'm happy to hear that ... I might do a video how to replace the fuse....is ok to remove the old fuse with the heat gun... Take the BMS off you don't want a battery to blow in your face ... Or lift the BMS slightly and put a heat shield underneath..... Don't solder the fuse with the heat gun top of the fuse is made of plastic will destroy the heating element inside.... You need to solder it back with the soldering iron 👍 ... Regards

@samvandop9539

8 күн бұрын

@@Razspareparts thank you for your tip. I think I will only use the heat gun to remove the fuze. Also i will lift up the BMS and put heat shield to protect the cells. Thank you for the TIP!!! I also thought the same about to use a soldering iron to solder it back on instead of using the heat gun. But there is some sort of plastic layer on the BMS/fuze. How can I remove this layer? And when do you think you going to make the video otherwise I will wait on your video bit scared that I fuck it up..

Had this question, you know on s5 when you ring a bell lights would flicker. Is it possible to teach s3 same thing?

@Razspareparts

8 күн бұрын

Sorry, no idea about that ... I know that you can find extra settings in moofer app but doesn't seem to work ..

Reset the charger like you showed. Left it plugged in for 4 hours. Skull on the display now. No charge in battery. No way to connect to app on phone. Low noise like broken disc drive from smart cartridge when plugged in?

@Razspareparts

3 күн бұрын

@@BFitz1976 please open up and disconnect the matrix display try again .... That display gets shorted and when it does .... Makes that annoying noise... So just unplug the display and as you do put the charger in I think Will start. ... I have replacement display on my eBay store ... Check ✔️

@BFitz1976

2 күн бұрын

@@Razspareparts Cheers, will try. No place here in Ireland to help.

Hello guys, my English isn't the best and I wanted to ask if I understood everything correctly. If my battery is completely discharged, can I connect the charger directly or do I have to adjust something on the charger? If the battery cells have different voltages (+-0.5V) because I charged them individually, can the battery management system compensate for this? If everything is working normally again, can I use the vanmoof charger or should I buy a new one? Thank you very much for the videos.🫶

@Razspareparts

6 күн бұрын

@@Tuner1 just spin the potentiometer as I do. And than try ... It might start charging