Vaillant Fault F28 29 54, Resistance gas valve & HT lead readings
Жүктеу.....
Пікірлер: 37
@Williams_Images Жыл бұрын
I had a f28 reading on my vaillant boiler & wasn't getting any hot water or heating..reset it, held down the 2 top buttons while it said loading then released them. The little flame symbol appeared in the bottom right of the screen, the boiler fired up & hot water came immediately. Many thanks for this video, very helpful
@sheriefgerges7789 Жыл бұрын
Brilliant video, what I would like to say 1.The bottom solenoid 119 ohm is fine even brand new resistance is same exactly as you said 140 plus or minus 10% 2. The yellow plug the diagram to test between one and no.2 pin the multimeter was on 1 and 3 , the 117ohm between 1,2 inch I love your videos alot of knowledge
@warriorsofwarmth
Жыл бұрын
Thanks for the positive feedback, I’ve a hectic life and individuals like u give me motivation
@kpereira8910 Жыл бұрын
Thank you Sir. Please keep them coming. Brilliant video. Thank you again for sharing your knowledge.
@warriorsofwarmth
Жыл бұрын
Thank u I really appreciate your feedback x
@dickiedubs3137Ай бұрын
Totally agree on the fuel poverty, i see some shocking poverty. Scares me how little safety net there is these days and the government paints a picture of people milking it....the reality is the polar opposite
@andrewtimmins8469 Жыл бұрын
Absolutely brilliant video 👍👌
@warriorsofwarmth
Жыл бұрын
Thanks I appreciate your feedback
@MijoshJoseph Жыл бұрын
very helpful many thanks
@warriorsofwarmth
Жыл бұрын
Thanks for the feedback
@michaeltrimmer88994 ай бұрын
Good video
@tomstrutton43512 жыл бұрын
Should you not do air integrity with the case on?
@warriorsofwarmth
2 жыл бұрын
Yes good spot!
@worldofparker5 ай бұрын
so useful, thank you, I like the close ups of the electrical tests. When you are testing the gas valve pressure, I presume it is at test point1 and not 2?
@danwyllie309 Жыл бұрын
Great vid mate. I had a problem with one of these valves recently, wish I had known this info at that point. Any chance you can confirm what the bottom ohms check should be (140 +/- 10%) and and what of the 6 pins are the correct ones to test between?
@luisangelrevillavallecillo716611 ай бұрын
Muy interesante tu vídeo. Te sugiero que pongas subtítulos en español. Gracias un saludo desde 🇪🇦
@stuartduffy8218 ай бұрын
Great video thanks for sharing is there an app for resistances on gas valves leads etc
@V12BHP Жыл бұрын
F28 on a Vaillant Ecotec Pro turned out to be low water pressure in the heating system in my case. Increasing the pressure fixed the problem.
@warriorsofwarmth
Жыл бұрын
Yes, after awhile they can seize due to dirt etc
@SuperWayneyb2 жыл бұрын
🤘😎🤘
@richardpayne2456
2 жыл бұрын
The HT LEAD
@BaluchBisharaf5 ай бұрын
Hi My reading is 0.746 on vaillant ignition lead . Is that ok or i need new one. Thanks
@warriorsofwarmth
5 ай бұрын
need a new one definitely
@richardpayne24562 жыл бұрын
Where did you put the black negative to test from?
@warriorsofwarmth
2 жыл бұрын
for which component?
@rahatdesite6 ай бұрын
HELLO! Very Very good explanations. Thanks a lot. Never seen an explanation so good in my life (drawing + what to expect + how to measure in reality). There is something that is not clear to me and I will need your precious help, PLS! The bottom resistor should be 140 OHMI (10% tolerance + or - ) you said. Plus would be 140 + 14 (10%) = 154. Minus would be 140 - 14 (10%) = 126. The meter is saying 119 (not between 126 and 154) => faulty resistor if my understanding is correct. Why do you say 154 and 185, please? Thanks a lot for your video!!!
@warriorsofwarmth
5 ай бұрын
there is two solenoids
@Dave-zg5xl Жыл бұрын
At 5.33 you say the reading was 1, 1 what? The actual display was showing meter out of range. If the reading was 1 it would display 1.something. not just a digit 1 on its own. Is your meter calibrated?
@warriorsofwarmth
Жыл бұрын
Sorry I am partially deaf
@dickiedubs3137Ай бұрын
Can I ask where the gas pressure test point is on the sustain....i can't find it on the gas valve
@warriorsofwarmth
Ай бұрын
Look on the gas isolation valve underneath
@dickiedubs3137
Ай бұрын
Yeah seen that one, normally there's one on the gas valve itself, I went to a f28 fault two days ago and couldn't find the pressure point on the gas valve to see if it was opening up
@alexriley6663 Жыл бұрын
Flue integrity test with the case off?
@warriorsofwarmth
Жыл бұрын
No ?
@skypool1005 ай бұрын
Any on f. 61 on eco tec pro 28 I'm sure it's faulty gas valve
@warriorsofwarmth
5 ай бұрын
u guage see if GV opens?
@skypool100
5 ай бұрын
@@warriorsofwarmth checked after 10mb on dhw, going to swap it out
Пікірлер: 37
I had a f28 reading on my vaillant boiler & wasn't getting any hot water or heating..reset it, held down the 2 top buttons while it said loading then released them. The little flame symbol appeared in the bottom right of the screen, the boiler fired up & hot water came immediately. Many thanks for this video, very helpful
Brilliant video, what I would like to say 1.The bottom solenoid 119 ohm is fine even brand new resistance is same exactly as you said 140 plus or minus 10% 2. The yellow plug the diagram to test between one and no.2 pin the multimeter was on 1 and 3 , the 117ohm between 1,2 inch I love your videos alot of knowledge
@warriorsofwarmth
Жыл бұрын
Thanks for the positive feedback, I’ve a hectic life and individuals like u give me motivation
Thank you Sir. Please keep them coming. Brilliant video. Thank you again for sharing your knowledge.
@warriorsofwarmth
Жыл бұрын
Thank u I really appreciate your feedback x
Totally agree on the fuel poverty, i see some shocking poverty. Scares me how little safety net there is these days and the government paints a picture of people milking it....the reality is the polar opposite
Absolutely brilliant video 👍👌
@warriorsofwarmth
Жыл бұрын
Thanks I appreciate your feedback
very helpful many thanks
@warriorsofwarmth
Жыл бұрын
Thanks for the feedback
Good video
Should you not do air integrity with the case on?
@warriorsofwarmth
2 жыл бұрын
Yes good spot!
so useful, thank you, I like the close ups of the electrical tests. When you are testing the gas valve pressure, I presume it is at test point1 and not 2?
Great vid mate. I had a problem with one of these valves recently, wish I had known this info at that point. Any chance you can confirm what the bottom ohms check should be (140 +/- 10%) and and what of the 6 pins are the correct ones to test between?
Muy interesante tu vídeo. Te sugiero que pongas subtítulos en español. Gracias un saludo desde 🇪🇦
Great video thanks for sharing is there an app for resistances on gas valves leads etc
F28 on a Vaillant Ecotec Pro turned out to be low water pressure in the heating system in my case. Increasing the pressure fixed the problem.
@warriorsofwarmth
Жыл бұрын
Yes, after awhile they can seize due to dirt etc
🤘😎🤘
@richardpayne2456
2 жыл бұрын
The HT LEAD
Hi My reading is 0.746 on vaillant ignition lead . Is that ok or i need new one. Thanks
@warriorsofwarmth
5 ай бұрын
need a new one definitely
Where did you put the black negative to test from?
@warriorsofwarmth
2 жыл бұрын
for which component?
HELLO! Very Very good explanations. Thanks a lot. Never seen an explanation so good in my life (drawing + what to expect + how to measure in reality). There is something that is not clear to me and I will need your precious help, PLS! The bottom resistor should be 140 OHMI (10% tolerance + or - ) you said. Plus would be 140 + 14 (10%) = 154. Minus would be 140 - 14 (10%) = 126. The meter is saying 119 (not between 126 and 154) => faulty resistor if my understanding is correct. Why do you say 154 and 185, please? Thanks a lot for your video!!!
@warriorsofwarmth
5 ай бұрын
there is two solenoids
At 5.33 you say the reading was 1, 1 what? The actual display was showing meter out of range. If the reading was 1 it would display 1.something. not just a digit 1 on its own. Is your meter calibrated?
@warriorsofwarmth
Жыл бұрын
Sorry I am partially deaf
Can I ask where the gas pressure test point is on the sustain....i can't find it on the gas valve
@warriorsofwarmth
Ай бұрын
Look on the gas isolation valve underneath
@dickiedubs3137
Ай бұрын
Yeah seen that one, normally there's one on the gas valve itself, I went to a f28 fault two days ago and couldn't find the pressure point on the gas valve to see if it was opening up
Flue integrity test with the case off?
@warriorsofwarmth
Жыл бұрын
No ?
Any on f. 61 on eco tec pro 28 I'm sure it's faulty gas valve
@warriorsofwarmth
5 ай бұрын
u guage see if GV opens?
@skypool100
5 ай бұрын
@@warriorsofwarmth checked after 10mb on dhw, going to swap it out