Thanks bro,,, it was helpful.. you saved me from heat today

Thank you pavan . This saved my day💥

Thanks lot. I was searching this installation video

Thank you for the video.

Thanks for the video

sir, thank you so much today we purchased Rs.3500 from Girias, but salesman don't know to assemble the partstomarrow i will try, thanks once again ,

Helpful video 👍

Thanks it was useful

I purchased for rs .2600. Your video is very helpful for setting this.thankyou

Much helpful❤

Thank you 🙏

Thanks

Hi bro,I have assemble the same fan seeing your video , how to stop fan from oscillating , I even pulled lever . Any suggestion ?

@CleanReview

3 ай бұрын

Try tightening lever like a screw to fit properly and then try pulling or pushing

Nice

❤

Thank ❤❤❤❤❤

Hi bro. How to pull up the inner steel pipe for height adjustment. Cant able to pull up

@CleanReview

11 ай бұрын

Hi , At starting it will be little bit tight , Can you try applying some soap or oil around edges from outside and try pulling up .

@Mju98

11 ай бұрын

Yes. I assembled. Speed is okay. But noise is high. While using Flipkart refund option I only get the replacement option. Can I replace this and get other model of v guard?

@CleanReview

11 ай бұрын

Yes you can try replacement, Fan which I assembled not getting much noise.

@kumarisimran1857

2 ай бұрын

I am facing same issues I tried a lot but it's not opening

any suggestion to lower the speed of the fan at number 1 only

@CleanReview

3 ай бұрын

That's not possible

Thank you!!!🙏

Thank you for your suggestion

Please someone tell me whether this stand fan can be used as a table fan.

@CleanReview

Ай бұрын

No, this fan height will be suitable for placing near sofa or near bed . If you are looking to use this while sitting on floor or sleeping on floor , then this is not best.

What is the condition now? Is it good?

@CleanReview

6 ай бұрын

Yes , It's good . No issues so far

Hi my standing fan head doesnt bend how do i fix ir

@CleanReview

5 ай бұрын

There will be a screw on one side below fan housing. This screw will help in bending fan by loosening it . Tighten it back after adjusting.

@sanjay1412

5 ай бұрын

@@CleanReview tried loosening it and tighten it but still goes up again.Btw this is a new standing fan

@CleanReview

5 ай бұрын

Then you can try replacement if you had purchased through online .

Is the fan leaf 🌿 made of plastic or metal?

@CleanReview

Ай бұрын

Plastic

Cord wire length?

@CleanReview

5 ай бұрын

1.5m

I couldn't loose/remove the small screw can you tell me how to loosen it

@CleanReview

4 ай бұрын

Which Screw you are referring to? small and large black holders?

Is this noise is too much,and what about power consumption??❤

@CleanReview

5 ай бұрын

Noise level is low to medium (depending on speed level). If you use for 8hrs at high speed approximately 2units of power is consumed.

@sekhartony8967

5 ай бұрын

@@CleanReview thank you bro ,and any double door refrigerator under 23000

@CleanReview

5 ай бұрын

Check this : www.samsung.com/in/refrigerators/double-door/rt3500mh-digital-inverter-technology-236l-titanium-silver-rt28c3032gs-hl/ I will add few links from other brands here

🙏🙏

Is screw driver available in the package?

@CleanReview

4 ай бұрын

No

@punithgowda8107

3 ай бұрын

What the heck 😂

Fan rotating not stoped

@CleanReview

5 ай бұрын

Did you tried pulling or pushing knob which is available back side above motor unit?

@sibinss1176

4 ай бұрын

Same issue​@@subhajitnayek7267

@user-ix7su7ie4f

4 ай бұрын

Same

@ShekharDigal-xi7fk

3 ай бұрын

Bruh it's working u hv to pull up backside rotating knobs 😅😂 but fan speed not upto the mark okk noise level is medium ...

How to stop oscilation any one can say ......

@CleanReview

9 күн бұрын

Pull up knob on top of motor to stop oscillation 03:16

@kaushiksarkar1516

9 күн бұрын

Thank u for ur reply , I did this same but can't stop _ V guard esfera STS N

@CleanReview

9 күн бұрын

@@kaushiksarkar1516 try removing knob by loosing it and tighten it back

dude that ring does't get tight at all, that screw just comes out. Don't know how to fix it

@CleanReview

2 ай бұрын

Ring that used to join two metal frames?

Which fan is good 1350rpm or 2100rpm?

@CleanReview

4 ай бұрын

If you want very low noise and medium air delivery go with 1350rpm. In 2100rpm , noise is medium at high speed but air delivery will be much better than 1350rpm.

⭐ Promo'SM

Fan leaf plastic or metal

@CleanReview

5 ай бұрын

Plastic

Bro rotating problem

@CleanReview

3 ай бұрын

Is pulling back side knob not working?

@user-ix7su7ie4f

3 ай бұрын

@@CleanReview twice pulling or pushing it's working

I purches today flipkart 2490 rupees

I purchased for 2350😂

@GareeBoooo0

3 ай бұрын

How bro ?

@PiyushKumar-ge8hs

Ай бұрын

Working good ??? Want to buy

Kowjksksiis🫥

. no

Wrong fitting

Bro fan is speed is not at all good

@CleanReview

17 күн бұрын

In V guard pedestal fans this is only fan with high speed capacity (2100) . Other v guard pedestal fans comes with lower speeds.

Is round Base plastic or metal ?

@CleanReview

2 ай бұрын

Base internally made of some hard high dense material and covered with ABS plastic