Love this book! kzread.infoUgkxpCNxqmAkyjN6NPx1fyB7QiEFWyO5mUWL it is simply one-of-a-kind! I really love it, because karah explained all tools required to have the job done, not mentioning the fabulous diy pallets ideas. I'm pretty sure this will be a fresh start in my new endeavour. Amazon was great, they delivered on time. Thank you!

Thank you, my dad passed away recently and left a run down trailer that needed replaced. That info was just what I needed. Thanks again

Straight and to the point. This is how a DIY video should be done. Subscribed.

I did not know that angle iron could come out. That makes replacing the deck so much more easier. Thanks for uploading this video!

Thanks for this video! I struggled for hours trying to figure out how to approach this on my trailer and didn’t realize that rear lip came off. Thanks again!!!

Most trailers are designed for conventional lumber, with out ripping. Spaces between the boards is usually not needed because the boards shrink as the get old and dry out. It's usually 11 2x8....or 10 2x10...I build theses trailers for a living.

@darrinmiller8030

5 жыл бұрын

Perhaps you can help me. I inherited an old flat trailer, with no wood floor. There is a channel on the front and the back of the trailer. How do I put the boards in so that they catch in both channels? There are no screw holes in the support angle iron underneath, so somehow the old boards were put in place without being screwed down.

@tonysimpson6873

5 жыл бұрын

@@darrinmiller8030 I'm in the same boat. I have no idea how to put the new boards in

@minojones8429

5 жыл бұрын

Darrin Miller you can cut the bead of the weld at the end of the angle iron so you can lift it out and put the boards in and then either tack it back down or screw it back on like in this video. I did it to my trailer and it went well.

@Duncan984

2 жыл бұрын

Hmmm

@aidenchaffee5568

Жыл бұрын

What should I use on my 6x12 with out having to rip the last board?

Repainting the cross braces of the trailer while the floor was out would have been value added. Also treating the floor boards with Thompsons water seal before installation would have added years to the wood.

Awesome, that was easier than expected! Mine is going to need the same treatment soon, but I won't put it off a long as you did ;)

The best and simplest video for this that I have seen. Great job and thanks!

Here’s a trick for everybody...... every time I change the oil in one of my vehicles I collect the spent oil in a 5 gallon pail and then every couple or three years I pour the oil onto the deck of the trailer and sweep it in with a broom I would buy for $1.50 at the dollar store which I would later throwaway Oiling of the deck does 2 things: it prevents the deck boards from rotting and it prevents the deck from shrinking without doing my trailer which has a 16 foot long footprint lost 2 inches, when we tried to load cargo which was exactly 16 feet long we were unable to close the back doors,these 2 inches came back a few days after the trailer deck was oiled

Nice video, I have a 5×10 heavy duty trailer that needs new flooring. That was a great video. Thanks

This is awesome thank u guys just what I needed for my 6x12! 👍🏼

@aidenchaffee5568

Жыл бұрын

What wood did you use for your 6x12

Another great video. Thanks for posting. I especially like how you skipped over the "quiet cursing and frustration" phase of the stuck bolt situations...

@StoneandSonsWorkshop

6 жыл бұрын

Shhhh.... Lol. Glad you enjoyed it.

Unless you paint the frame with rustproofing primer and paint, the job is only half done, and will lead to unnecessary work in the future.

Excellent job on the trailer. Love your vids. Thanks for sharing.

@StoneandSonsWorkshop

6 жыл бұрын

+LesterElm1 Thank you!!

Here in Arizona wood gets recked by heat and sun in just a few years. Thanks for this.

What kind/size screws to hold the boards down to the metal or you only screw the ends of it

Mine has those same rusted mounting screws. I will cut them too and wood as well. Nice vid.

WD 40 is a water displacer(WD stands for “water displacer”)NOT a penetrating oil. Use Kroil, PB blaster, or ATF/ acetone mix.

@kayeyeager8006

2 жыл бұрын

PB is my go-to as well.

@williamrodriguezmswlcsw8119

2 жыл бұрын

You are correct, but wd40 does offer some penetration. Check out the comparison on project farms channel. Very interesting results. 👌

Super helpful - thanks for the time saver !

Thank you for this vieo. Would you tell what kind of wood you use or is the best for this project? TY

Used spray undercoating on the siderails after cleaning off loose rust.

Once I went to that trouble think I would have cleaned it up and give it a coat of rust proofing. Know your a busy man, is that what we call in Aussie treated pine!!!!

@paulsilverman2944

3 жыл бұрын

Just use old engine oil after you change your cars oil why waste of money with store-bought stuff

@billsimmons2898

3 жыл бұрын

or at least some Undercoating to kinda slow down the rust creeep..

Great job now I have the motivation to do mine

I just did the samething today , how did u take off the screws that u cut off ? Did u use a punch?

Question: my trailer has 2 rows of additional fasteners along braces a couple of feet fore and aft of the mid brace. Did you just decide the additional fasteners were unnecessary?

How did the gap work out after the new boards dried I have read different opinion in regards to spacing new wet pressure treated boards for my 5x8 utility trailer.

I have found PB Blaster to be a great rust penetrant. Regardless, the sawzall worked. Nice job!

@StoneandSonsWorkshop

6 жыл бұрын

+Jeremy Condon never heard of that. Thanks!

@robertharris2432

5 жыл бұрын

I found Freeall is much better anything else. I tried PB blaster and it did crap. Then I used Freeall, loosened in minutes.

@Praise___YaH

8 ай бұрын

Guys, HERE is our Savior YaH The Heavenly FATHER (Genesis 1) HIMSELF was Who they Crucified/Pierced for our sins and “HERE IS THE PROOF” From the Ancient Semitic: "Yad He Vav He" is what Moshe (Moses) wrote, when Moses asked YaH His Name (Exodus 3) Ancient Semitic Direct Translation Yad - "Behold The Hand" He - "Behold the Breath" Vav - "Behold The NAIL"

Both my angle irons front and back are welded in

Nice simple fix...............They don't always go that way...... Was that a rebuild trailer?

You mention securing the board’s underneath the trailer. Is there a video on those? Thx

Good video and tips. Thanks for this.

That came out nice. Thanks for sharing. A new trailer deck is refreshing. I did mine about 10 years ago. It was long overdue as well. See you next time!

@StoneandSonsWorkshop

6 жыл бұрын

+DIY Dillon Thanks! It’s definitely refreshing.

@joedonabdrnathy7603

6 жыл бұрын

Dillons Woodworks b

Were there any screws besides the end caps that you re-installed? I'm getting ready to do this on my trailer. Thanks.

So you don't put the same type of bolts back in? You use wood screws from the bottom? Will that hold as well as the original bolts?

Did the torx screws come out easily :12-16 second mark. And did you screw the boards back into the frame?

no screws or bolts in boards down the length only ends>?

Nice work Shawn!

@StoneandSonsWorkshop

6 жыл бұрын

+Vincent Alex Vigil Thanks!

Is the new wood just laying in there or is it necessary to screw it down? Seems like it would be tough going through that metal.

Do you have to space the oards? Or can you have no space between? thanks

What size of wood did you use?

Looks great Shawn. Did you use treated wood? That is a really nice size trailer. That is something like what I want to get for my next trailer. Thanks for sharing

Perfect instructions, thank you sir

Both pieces of angle iron on my Big Tex trailer are welded. Anyone else have this? Is there a technique to replace the floor boards w/o cutting those welds?

Thanks for the tip great video

What size boards did you use? I have 1x6 I would like to go up 2x10 Will it work?

How does it keep it down for a right snug fit

My Tip: For cosmetic purposes only, I would have placed the cut board in the centre of the trailer floor.

@rb79er

4 жыл бұрын

Probably not in the middle as the hand cut line would not be as straight. For cosmetic aka symmetry, he could have cut the piece on the other end, but that's more work and no one really cares as it is just a trailer bed :)

What size were the boards

Where do you find wood that straight?

A manual impact screwdriver is priceless for rusted screws

Good info here! Thanks for sharing!

Great video mine little different homemade built from previous owner at the gate I didn’t have screws on top nor bottom. I was told to remove gate then cut angle iron or bar that it slides in then re weld crazy huh. I can tear it up just need to get a good solder kit now lol.

The only thing I plan to do different on mine is once the boards are cut to size apply the preservative on all sides then install

@smsteger89

2 жыл бұрын

Technically all it really needs is oil. There's no point in finishing a trailer bed. The finish will just come off quickly if you use it with any regularity. Any kind of oil will do, just do it every so often. Not like every month, just maybe once a year or two.

I wanted to put my safety glasses on watching your attempt to remove that stubborn screw! Lol

Nice job. One suggestion i have though. Instead of waiting until the last board to rip. Get your measurements and put the ripped board in the center for a more symmetrical look. Thanks

@talkingcargojunkremoval

3 жыл бұрын

A wise man speaks 👍👍👍

@AK74Man87

3 жыл бұрын

Definitely, was told to start in the middle and work out. You can possibly make the two end boards more narrow if possible.

@cfbarnett

Жыл бұрын

My plan is to start in the middle and work to the sides. That would leave the narrowest boards on the edges rather than in the center. It's one concept anyhow.

I'm really surprised you didn't paint that metal with a rust stopper paint when you had it exposed

@indoorcomfort6021

3 жыл бұрын

Same thoughts

@cfbarnett

Жыл бұрын

I read an earlier reply to a similar question. The original poster said he would do that at some time in the future but he was in a hurry to get a functional trailer up and running.

On your stripped screw heads try an angle grinder, and make a slot in the head and try a Flathead bit. while all the boards are off might as well get a wire brush and get as much rust off the framing as possible, and repaint it.

@StoneandSonsWorkshop

4 жыл бұрын

At this moment i was just interested in a functional trailer. Later on I might rework the entire trailer.

No need to space newly purchased treated wood. It’ll dry and shrink. Good job!

@FredMiller

5 жыл бұрын

Absolutely!

At 5:09, you nailed the retaining bar down onto the boards. But the boards (with retaining bar) aren't connected to the trailer at all, right? So a crazy bump could lift the whole rear of the boards a couple of inches and it could start sliding rearward, correct? Especially if you removed the rear gate in order to haul kayaks or something a bit longer than the bed. I think I'd put 4 or 5 holes in the front retaining bar, too. The one that's still welded down. And driving screws in there would mean the boards couldn't "jump" and slide out of the deck, no matter how big of a bump you hit.

@warrenmichael918

Жыл бұрын

I see that the same way. I have almost the same front and rear angle iron set up on my trailer with no screws holding the boards down to any cross members in the middle, EXCEPT i made sure to use bigger screws to go through to the frame at the end of the trailers frame at the end.

I simply cleaned the head out with a screw and compressed air and worked the impact forward and reverse until they came out no lube. The lube will make the heads strip

What about boards with screws down the boards?

what size are the boards? 2x6? 2x5?

How much would that cost in 2021 lumber $?

Nice job! 👍👊

@StoneandSonsWorkshop

6 жыл бұрын

+Fred McIntyre Thanks Fred!!

Such a great video

Durn nice job, looks good and done right!

@StoneandSonsWorkshop

6 жыл бұрын

It’s solid. 👍

@18winsagin

6 жыл бұрын

Stone and Sons Workshop I'm about to do my 5x8, the stamped metal is shot and I'll take the real bad stuff out and want to go back with maybe 2x6 boards or I kind of thought about looking at those poly decking boards since I only haul my mower and some light stuff around the house.

Those are M30 star bolts. Your bit was probably too small and stripped the bolt pattern. How do I know this? Because I did the exact same thing! Great video, thanks!

@tlc5343

4 жыл бұрын

foodboy767 ...... T30

What size wood is this?

Now you can take a trip to see Matt Cremona and buy some slabs!

What sise it's the wood

Thanks a lot for the video

Why wouldn't you Por15 or at least Rustoleum the frame before attaching the boards? Lots of rust on those cross bars!

@StoneandSonsWorkshop

6 жыл бұрын

+Trey Horsey it may look bad, but it’s really not. I did look at everything to make sure there wasn’t any serious issues. There’s a lot I COULD do, but at this point I’m just interested in a new floor.

@waynewilliams5802

3 жыл бұрын

He seemed like a nice guy but he aint no Bob Villa.

@smsteger89

2 жыл бұрын

Never use por15, you cannot stop rust without getting rid of it first. Painting over it will never stop it. The only way to stop rust is by removing it. Rust is a chemical reaction and once it has started it is too late. You have to remove it, then prime the bare metal, then paint/seal over the primer. Por15 is a gimmick.

Good job, Shawn. That repair should last you quite awhile now.

@StoneandSonsWorkshop

6 жыл бұрын

+steve walker yes it should. Thanks.

Just wanted to share this, Kroil is far superior to WD 40 to get into stuck screws and bolts in about the same soak time. try it once you will agree. It might cost about 8 bucks a can but it is worth every penny.

That was a good simple project. When you were struggling with the screw, you said you couldn't get under the angle. You could have cut through the wood to get to the screw. We tend to forget that we can destroy the piece we are replacing. While you had the deck off did you inspect the wiring. On my nearly new trailer, the wiring is not up to my standards. I haven't felt motivated to crawl under it to fix the wiring.

@StoneandSonsWorkshop

6 жыл бұрын

+B Templeton Haha you’re right I could’ve cut the wood, and yes I did check the wiring. I was going to add the whole wiring thing to the video, but that it was a little bit off topic.

@n5uge12

2 жыл бұрын

Great point. Thanks.

@cfbarnett

Жыл бұрын

@@StoneandSonsWorkshop My boards were so rotten that a grandson had a great time with a sledgehammer beating them to death.

Don't space wet wood. When it dries, the space will widen further.

@cfbarnett

Жыл бұрын

kiln dried wood shouldn't shrink much

What kind of wood.

Recommendation for drilling on trailers that DONT have bolts already? 1 hour in.. 4 broken bits. Not one complete hole

At the very end where you screw the angle down to the boards. Does it hold the boards down? It dont flop up in the back? mine is welded. I am actually fixing to redo my boards but don't have a welder to re-weld it. but if your method works then I'll go that route.

@freedomgunsandliberty

5 жыл бұрын

Yeah it looks like it would flop around. Mine's welded also so I have to cut the angle off then reweld it. Luckily I have a welder. Go buy you one at harbor freight cheap and if you don't want it after the job then return it 😉🍻

@jsboening

4 жыл бұрын

Just bow the boards up in the middle so you can get the ends to slide in the groove then release them.

Wat time i go look for

Did you screw the boards back on from underneath the trailer?

@seanchildress3137

4 жыл бұрын

That's my question as well. Seems like the trailer will flex and eventually warp or cause welds to fall under load.

I use used motor oil cut with diesel to preserve the treated lumber on all my trailers. Just a thought. Great stuff Shawn. There are a bunch of people out there that would just trade it in instead of what you did (the right thing)

@DarkLinkAD

5 жыл бұрын

How long does the smell last?

@briangarcia2358

5 жыл бұрын

@@DarkLinkAD I was thinking the same thing. I park my trailer in my garage, and I dont think I'd be able to ever do that again. I would bet the smell will always be there

@daverea372

5 жыл бұрын

No just no. Used motor oil will rot your lumber! Its what people pour on old tree stumps to rot them away,..why? Cause it does!

@smsteger89

2 жыл бұрын

I don't think I would use anything like used oil, but the idea is true, you want to oil your deck at least every couple years.

@brich2929

Жыл бұрын

@@daverea372 no it won't. It preserves it.

Thanks, good job. When you get to my age you will realize the benefit of knee pads.

Might be a silly question but...Did you make the small gap between boards just for water drainage?

@r.b.dickson8825

2 жыл бұрын

I never again put a space between the boards cause they will shrink in time creating the perfect gap..

So did you only put screws in the end with the angle iron cap ?

@frankgrimes342

4 жыл бұрын

Scratch that watched it over again

They welded mine shut I gotta cut the metal lip over the wood on one side. Tsc trailer....

Well the only way I've ever done replacing decks on trailers car and semi is drill out the heads on the angle or retainer piece. Then remove the loose broken boards. Then seawall all the screws flush with the lower frame work. When reinstall you font have a bunch of holes in it to get lined up just drill new and run in decking screws. I did tons of trailers whern I worked in my apprenticeship and early when I worked at Ryder and other truck shops. The young guy gets the hard jobs. The old mechanics said we still had gristle for a spine so it wouldn't hurt us. Lol

@cra2cra226

3 жыл бұрын

plz post a video. not sure i follow.

Treated material as a replacement, is it silly to say a coat of paint adds to the longevity of the timber ?, not sure but my dad always painted most projects so I’m in that mould of thinking 👍

@StoneandSonsWorkshop

6 жыл бұрын

+Sumo's Projects if I do anything, I’ll eventually add a sealer. I really dislike painting. Lol.

Excellent to the point and informative! Question, my trailer is nearly identical except it is 12’ and the rear angle iron or channel is not removable. It is welded all the way around the entire perimeter. Have you seen this before and have any recommendations? Thank you

@agentleebs

Жыл бұрын

Mine was 16 ft. I used a hydraulic jack underneath (with a scrap of wood to not dent the trailer wood, to bow the board to get them out. Reversed the procedure to put the new one in. Two people would have made the replacement easier, I used a clamping system to push the one end down. Once it’s lined up, then you can ease the jack down.

@SmokeyBear363

Жыл бұрын

Cut a piece wide enough to slide and remove the boards

@cfbarnett

Жыл бұрын

@@agentleebs I have a 10 foot long trailer and have the same issue with the rear angle iron. Bending a practice 2x6 but think that if I bent it enough to slip it in there it might break. Over a 16 foot span that would work easier. I have to do some more research on this. I can cut the boards shorter so the bend might work but would like to have as much length under the iron as possible. I welcome any help you might have.

@cfbarnett

Жыл бұрын

@@SmokeyBear363 Not sure what you meant, Mario.

@cfbarnett

Жыл бұрын

Reading further I see that people have cut that angle iron in the back and then rewelded it or screwed it down somehow. I'm going to research that.

What type of screw did you use to secure the decking to the trailer?

@warrenmichael918

Жыл бұрын

I dont think he did. It looked like the front edges were under the front angle iron and the rear was also covered by that piece of angle iron. I just wondered if the rear boards could still bounce around because i dont think the 3 screws were into the trailer frame to hold them all down.

just curious my trailer the boards are screwed down every few feet to a cross bar. when i put new wood down how would i line back up to those threaded holes? Somehow i have to make holes in the new boards to line up to the threaded hole in the trailer cross bar. any ideas?

@jeremygifford1705

2 жыл бұрын

You'll have to drill your boards from the bottom side under the trailer through the existing holes in the crossmembers. Its easier if you stand your trailer up on it's ass end although that's easier said than done.

@jrdickersonish

2 жыл бұрын

I did this last year and watched this video just to see how he handled it. But he only showed himself sliding under the trailer. The rear angle bracket is the hardest because it has to go perfectly through 2 holes. I made a drill guide to insure I kept the bit straight and drilled from underneath. Once you make that first hole, put a bolt in it to keep it from moving while you do the others.

@jrdickersonish

2 жыл бұрын

I wasn't careful on one hole in the crossmember and drilled it bigger so the threads don't catch. That board bows up at that point. Since the bolts are cutting bolts, the drill bit can be slightly smaller than the hole and avoid reaming out the hole in the metal.

I'm gonna go ahead and do that. I went ahead and did that. Do you ever get to far ahead??..😀😉😉

No need to space them as they WILL shrink.

nice!!

I used my reciprocating saw and just cut off the bolt heads

I didn't see that you reattached the boards to the frame and the angle on the back looked like you only screwed it into the boards, not the frame. I'm just concerned that the boards could potentially come loose when hitting large bumps in the road.

@StoneandSonsWorkshop

6 жыл бұрын

+John Card I mentioned adding screws to the bottom center of the boards through existing holes, but the underside of the back I added washers and screws to the angle iron. So, everything is secured.

@johncard7203

6 жыл бұрын

Stone and Sons Workshop Ok, just wanted to make sure all was secure.

Where did you buy the screws to attach decking?

@cfbarnett

Жыл бұрын

Brad, did you find screws? I'm looking at torque's head black screws that can be had from Tacoma screw and fastener. They are self tapping so pre drill and run them in.

@bradhartsoe9128

Жыл бұрын

@@cfbarnett yes, thank you !

Can I use a trailer like this one to carry wood for a fencing job ?

@josephmccaslin1513

4 жыл бұрын

Duh

If that would isn’t pressure treated I would have stained it before putting it down to make it last longer. Looks clean though