Direct link to the terminal: www.amazon.com/Tinksky-Speake...
Жүктеу.....
Пікірлер: 22
@paulrevelli Жыл бұрын
That was actually an excellent tutorial on soldering! Thank you.
@photosshop3 ай бұрын
You should changed a speaker wire also when you been at work. Wire is to thin and a bad quality for the subwoofer.
@SamsMediaCenter Жыл бұрын
Thank you so much for the video. It looked easy when you do it. What gauge wire did you use? is it 16 gauge or 18 gauge? My subwoofer is Rockford fosgate R1s412 200W rms subwoofer. I soldered 14 gauge wire to the back side terminals just like you but when I switched on the amplifier it gave some sound and turned off immediately and didnt turn on until I removed the terminal. I used a push terminal with a hole. Both positive and negative terminals were connected properly. But when I connect the 14 gauge wire directly from subwoofer to amplifier without terminals, it works beautifully. Is 14 gauge wire too much for soldering it to the back side of terminals? Should I use 16 gauge or normal speaker wire? Please advise.
@benjaminbutton9910 Жыл бұрын
Can u show me how to connect the speaker wire to that kind like it detail
@ImAlwaysHidden2 ай бұрын
Hey so the wires that connect to my terminals are too short, what’s the wire called so I could maybe extend it ?
@nba2kvids431 Жыл бұрын
With what cable do you connect 2 speakers with terminals ?
@IvanRossS
Жыл бұрын
Yes of course. But your 2 subs have to be properly connected between each other in your box !!
@sermac32464 ай бұрын
👍
@Hiersom03 Жыл бұрын
What if my connector was smoking at one point and burned through the plastic piece, also if it’s not it a specific spot it sparks, how do I fix??
@IvanRossS
Жыл бұрын
You have to measure a resistant on your speaker there is a possibility your bass speaker blown
@IvanRossS
Жыл бұрын
Also your amplifier probably set too high
@IvanRossS
Жыл бұрын
Sparks is really bad your wires should not be hot. By keep running it you can damage a lot of stuff. Make sure your wires that coming from amplifier are thick enough
@Hiersom03
Жыл бұрын
@@IvanRossS no it’s the connectors, one of them melted through bc my wires were too thin
@Hiersom03
Жыл бұрын
@@IvanRossS spit moves and goes in and out I just need the new connector
@7350chuck Жыл бұрын
do you know what thr holes are for?????
@IvanRossS
Жыл бұрын
What holes ? On the terminals on the back ?
@djessievlogz3310 Жыл бұрын
upgrade or just replace??
@IvanRossS
Жыл бұрын
It's upgrade because this is a push to connect, not twist style.
@ceeweedsl Жыл бұрын
Why not just move the terminals to the new cup or the tab to the new terminal? No need to desolder etc.
@IvanRossS
Жыл бұрын
I did it so it will be a new solder . Fresh and clean
@devisissy12 жыл бұрын
Upgrade the name of the video to how to upgrade Terminals on SUBWOOFER BOX. Jesus.
Пікірлер: 22
That was actually an excellent tutorial on soldering! Thank you.
You should changed a speaker wire also when you been at work. Wire is to thin and a bad quality for the subwoofer.
Thank you so much for the video. It looked easy when you do it. What gauge wire did you use? is it 16 gauge or 18 gauge? My subwoofer is Rockford fosgate R1s412 200W rms subwoofer. I soldered 14 gauge wire to the back side terminals just like you but when I switched on the amplifier it gave some sound and turned off immediately and didnt turn on until I removed the terminal. I used a push terminal with a hole. Both positive and negative terminals were connected properly. But when I connect the 14 gauge wire directly from subwoofer to amplifier without terminals, it works beautifully. Is 14 gauge wire too much for soldering it to the back side of terminals? Should I use 16 gauge or normal speaker wire? Please advise.
Can u show me how to connect the speaker wire to that kind like it detail
Hey so the wires that connect to my terminals are too short, what’s the wire called so I could maybe extend it ?
With what cable do you connect 2 speakers with terminals ?
@IvanRossS
Жыл бұрын
Yes of course. But your 2 subs have to be properly connected between each other in your box !!
👍
What if my connector was smoking at one point and burned through the plastic piece, also if it’s not it a specific spot it sparks, how do I fix??
@IvanRossS
Жыл бұрын
You have to measure a resistant on your speaker there is a possibility your bass speaker blown
@IvanRossS
Жыл бұрын
Also your amplifier probably set too high
@IvanRossS
Жыл бұрын
Sparks is really bad your wires should not be hot. By keep running it you can damage a lot of stuff. Make sure your wires that coming from amplifier are thick enough
@Hiersom03
Жыл бұрын
@@IvanRossS no it’s the connectors, one of them melted through bc my wires were too thin
@Hiersom03
Жыл бұрын
@@IvanRossS spit moves and goes in and out I just need the new connector
do you know what thr holes are for?????
@IvanRossS
Жыл бұрын
What holes ? On the terminals on the back ?
upgrade or just replace??
@IvanRossS
Жыл бұрын
It's upgrade because this is a push to connect, not twist style.
Why not just move the terminals to the new cup or the tab to the new terminal? No need to desolder etc.
@IvanRossS
Жыл бұрын
I did it so it will be a new solder . Fresh and clean
Upgrade the name of the video to how to upgrade Terminals on SUBWOOFER BOX. Jesus.
@IvanRossS
2 жыл бұрын
Will do. Thanks