For my workshop, I bought a bucket with a sealable lid and fitted a cyclone unit. All the dust etc drops into the bin, nothing passes through to Henry- unless I let the bin fill too far! It's surprising how many I see thrown on top of skips by builders, I've picked up a few freebies, a few quid for new carbon brushes and black spray paint and jobs a good un.

@ReheatedDonut

15 күн бұрын

Yes just making a cyclone now myself, was hoping this video was a tutorial so could source some vacuum hoses etc as the prices seem pretty silly.

@s1udgeguts

15 күн бұрын

​@@ReheatedDonut I used the old hoses off my pond vac. To adapt these to the larger cyclone fittings, I just used plastic lemonade bottles and shrunk them to fit with a heat gun

The big hose arrived. Makes a huge difference. Also don't underestimate adding an air freshener 04:28. I threw one in an few days ago and just did a quick bit of vacuuming in the garage. Now it smells lemon fresh rather than of stale dust.

@Jamez1093

2 ай бұрын

Can you use a big hose with the standard pipes please? Need a good replacement as my pipe stinks with the henry😂 I bought off eBay

@JosephByrne

2 ай бұрын

The big hose has a big end that doesn't fit the standard wand.

Get the HEPA filter in your links. I have one installed, they are brilliant. Also, use Swirl vacuum bags. They're way better than the Numatic Henry bags but unfortunately a lot smaller. With your older more powerful Henry motor, that large bore hose plus thd HEPA filter and Swirl vacuum bag you'd have a dust extractor better than pretty much anything on the market at a considerably lower price. Oh and by the way, it's actually possible to buy a device that will enable your Henry to come on and off automatically after you switch you power tools on. This will allow you to keep Henry out of the way.

Great video mate. I'm going to order the bigger hose now.

I was just checking around for an efficient and pocket friendly dust extractor. Thanks for sharing.

Mate, your right two of my mates bought Henry’s last year 2023 and had to take them straight back. They rubbish now not the same.

Henry is a great little workhorse for what they cost! Regards JP

I picked up a used Henry from one of the neighbours. I didn't know about the motor differences but I've discovered it's the 1100W. I want to use it as a shop vac in the garage. I've ordered the big hose. Great video.

Thank you for your video. I'm trying to make extractor with cyclone (DIY). Your video is very helpful. 👍

@christopherinteriors6521

29 күн бұрын

You are welcome

Got a Henry today. Thanks for the tips. We are absolutely made up with it. It's to replace a cheap hoover we bought which was garbage. I think these machines are great value for money considering how long they seem to last.

Sweet! got a 1200w Charles, just ordered the hose, - was about to buy a whole dust extractor, now I don't need too!

You can't beat a Henry👍I've just ordered one of those yellow hoses, cheers.

@christopherinteriors6521

2 жыл бұрын

less blockages for you to deal with from now on 😂

Really good video thanks.

Henry vacuums are cheap in the UK but over here in Canada, you are looking at a price of CA$500. That's not too bad as a commercial canister but for shop work the better solution is Emerson's Ridgid or Workshop Vac brands. I guess you could get just a regular Shop-Vac brand machine too and all three brands come with the option of a plethora of attachments, many of them cross-compatible with each other.

Henry is by far the best for hard dust and debris especially if u use wide hose attachments there my go to for doing pop ups and after channeled shower trays, indoor screed cuts.

Great video. Interesting that I've got a similar set up. The cen-tec stuff is really useful especially as it fits the bosch stuff too. I think it's only 32mm though

Thanks for sharing as you've just saved me from forking out for the Festool. when I own a Henry and can simply upgrade the hose and filters awesome video thanks again for the golden advice.

I’m looking for a wet dry vac, and this is the first video I’ve seen by you. I love your honesty and clarity. I agree with you about the lower wattage meaning less power. I’ve decided not to waste any more money on new Miele or Dyson, ( I’ve bought three in the past four years, all were rubbish in terms of build, exterior casing and particularly suction) and I only buy second hand now with higher wattage. Thank you for taking the time and effort to give useful information about your Henry.

@lucifarian93

3 ай бұрын

I've got a Henry wash , amazing value carpet cleaner, the Charles is the wet one, very powerful .Bags for Henry I buy 30 at a time from Argos.

Thanks for the tips... I converted from 32mm to 38mm everything! The only downside is that I was p'd off when I received an Orange hose, not yelllow as you show and as stated and advertised on Amazon UK. All other accessories through "Beacon" except for the floor/carpet brush-head which is a Heavy Duty unit and slightly larger. The new "Henry" is still powerful enough to lift carpets held in place by "Gripper"... We tried all the cordless but, as you said, trades people rely on these "Henry" machines too! A decent smelly, as you advise, is far better than nothing...

get the nrv-240-11 its the commercial henry, 620 w so excellent power and a 9 ltr capacity. you can tell the difference it has the red bumper around the base.

I would nowadays purchase a numatic Charles or George for extracting. The modern Henry’s are great for general vacuuming.

Do the original tools still fit the upgraded hose or do you have to buy new snd or an adapter to make fit. Thanks for the tips

Hi mate just thought I'd inform you this one is from 2004 as the red rear wheels were introduced in 2004 unlike the black rear wheels from 1981 to 2003 though many machines are from the 90s thought I'd let you know for future reference bud

@matticetfan

10 ай бұрын

09:02 I do belive its 2003 as first 2 digits of a serial number corespond to the year of manufacture, and digit 3 and 4 corespond to the week number of that year ( exactly how car tires are dated) it was close enough I suppose.

Hey mate. Will those power tool adapters work with the bigger hose? The description sounds like they're for the original hose only

Can you tell me how your m8 used the cen tec click adaptors with the hose you recommend, I ordered the hose and all the adaptors I need and they don't fit, the cen tec is for 32mm hoses, the yellow hose is way bigger, so it's £35 wasted

You can get Charles too, which is geroge without the pump and carpet cleaning

@christopherinteriors6521

Жыл бұрын

I have a Charles but he only gets used for wet stuff/ cleaning out the van. I never use him for dust collection though.

I've just ordered a big hose, just wondering what you all use to make the connection to your saw's? All mine seem to use different size connections.

@s1udgeguts

2 ай бұрын

I use plastic lemonade bottles. Cut off the top, hit it with plenty of heat and the plastic bottle shrinks to fit. Makes a great, cheap, home-made adapter.

With the larger 38mm dia hose is the threaded end and the other end hole size the same as the original 32mm hose, as your Amazon link does not include my HVR 200A model?

@Jamez1093

2 ай бұрын

Did you ever find out mate need a new hose and want to use it with the original metal pipes

@Jamez1093

2 ай бұрын

Did you ever find out mate need a new hose and want to use it with the original metal pipes

Cool video. I want to sand a small brick wall with a sander. Would this handle it?

@christopherinteriors6521

Жыл бұрын

Most definitely. It is just as powerful as my Festool dust extractor. Builders have used Henry Vacuums for years for rubble, brickdust etc. I would get some of the hepaflow henry bags and it would be perfect.

Just bought a Henry nuematic 160. I onky have hard floors but lots of biggish rugs. Find the normal head is far too strong and lifts the rugs off the floor. I am elderly and need simplicity. Which tool, if any, should I use for rugs? Grateful for any advice.

@cynthiastogden7000

Жыл бұрын

Ps think I saw some advice in a bomment below. Thanks.

@christopherinteriors6521

Жыл бұрын

Hi Cynthia. On the metal pole there should be a thing which you turn and it let's air in. I believe that will lower the suction for when you are finding it too powerful. I know the feeling, they can be too powerful sometimes.

Hi Christopher, would you know if this will fit the George vacuum?

@barryrutter5936

4 ай бұрын

Yes as its a standard 32mm hose it should fit a george

I have a Henry - the standard hose is 38mm diameter. Why is the yellow hose better?

@christopherinteriors6521

10 ай бұрын

the standard hose is 32mm

I have George hoover. Do you think i can use it as a dust extractor as well? I need it for orbital sander. Thanks

@barryrutter5936

4 ай бұрын

Yes

@barryrutter5936

4 ай бұрын

Make sure u swap to a hepa filter along with hepa flo bags for maximum filtration

@jaroslawrogowiec9567

4 ай бұрын

@@barryrutter5936 thank you!

Where did u get the yellow hose

@christopherinteriors6521

2 жыл бұрын

There is a link in the description for the hose my friend.

How can one reduce the pressure. Just bought one but the suction pressure is quite high that it's difficult to use

@christopherinteriors6521

Жыл бұрын

On the metal pole there is a plastic collar that you can turn that makes a hole and it makes it pull less on the carpet. There is no actual pressure adjustment on the machine itself.

@ikechukwueberendu5920

8 ай бұрын

Thanks

Whats the model number for the older machines so i can find one?

@Mr_D2_1004N

10 ай бұрын

HVR200

Given the shortcomings that you outlined in the video would you still recommend buying it? It s about 160£ right now.

@christopherinteriors6521

Жыл бұрын

I would try to find a second hand older model as they have more powerful motors. You can usually find these on ebay or facebook marketplace for under £50.

@Sokradde

Жыл бұрын

Thanks for the advice

Try the reusble bags mate

@christopherinteriors6521

Жыл бұрын

I have used those before. They are great for cleaning the house but not good for things like dust extraction in my woodworking workshop. The particles are too small that they escape the zip on the bag and make a mess. They are also not HEPA rated. You are right though and I would recommend them for day to day cleaning.

Do you notice that the newer hepa flos are much worse than the older ones? Reduced quality?

@christopherinteriors6521

Жыл бұрын

I haven't bought any for a year or so. I bought so many when they were on offer in Tesco and I only use the Henry for my mitre saw now. It would be interesting to find out though.

What motor would you recommend please reply

@christopherinteriors6521

29 күн бұрын

The great thing about this video and channel is that there are so many enthusiasts in the comment section who would be able to advise you better than I can. I am no expert in Numatic vacuums but many in this comment section are.

Bit repetitive about the motor wattage, perhaps plan your script in future. That said, love the larger hose and the air freshener tip.

@christopherinteriors6521

10 ай бұрын

thank you for your feedback. I don't script videos, just bullet points. It was a year ago so hopefully I have improved on my repetitiveness by now.

Any links to the hose? The one linked is unavailable.

@christopherinteriors6521

2 күн бұрын

It seems to be available now. I think they must have sold out as so many people are watching this video and buying them😂

Obviously the end of the hose is alot bigger than standard what sort of attachment will fit this for sanders etc plus this don't fit the standard hoover attachments

@christopherinteriors6521

Жыл бұрын

That would all depend on the size of the port on the sander. I can't give you a specific answer as every single sander is different. Every single tool is different. I have 4 Sanders and the original Henry hose didn't fit on any of them. Every one of my power tools has a different size port and it is really frustrating. You can actually get adapters that change any sizes as I have seen them on ebay. Personally I make adapters for the tools that I use Henry for as I have so many tools. As for the standard hoover attachments, yes they don't fit as the port is bigger. There are bigger wands out there but again I made my own with some plastic pipe. As it only takes a couple of seconds to swap the hoses over and the hose being so cheap, I would recommend having both hoses. For the likes of a sander, the smaller diameter hose would be good as you don't need as much suction. For something like a mitre saw I would recommend the bigger hose. If you are clearing up on a job site then I would suggest the bigger hose as the port is bigger and allows you to hoover up larger pieces. Sorry for the long reply, I have tried to help as much as I can.

@Barlowpaul97

Жыл бұрын

@@christopherinteriors6521 thank you for your reply. I'll have a play round with it I just got the different filter you put in your post and and the smellys to go in hoover what a difference cheers mate

bought one it can't cope with brick dust when wall chasing. Shame, but great video.

@christopherinteriors6521

Жыл бұрын

Sorry to hear that. I would add that it is probably due to the extraction port on the tool rather than the extractor itself. Although I don't ever do chasing myself, I have seen electricians use my own and they have really praised it. Have you upgraded the hose?

He does look like he may have been drinking lol!

@christopherinteriors6521

2 жыл бұрын

It is either that or he has been sniffing something up his nose lol

Hose no longer available ☹️

@christopherinteriors6521

29 күн бұрын

You are in luck, they are available as I have just checked. Thanks for your comment

nice henry it is the 2003 model not the 1992 model

Too bad they don’t have the waterproof sealing ziplocks :)

It looks like a 2004 Henry 1:03

@christopherinteriors6521

Жыл бұрын

I don't know a huge amount about the model numbers. This one is made from mix and match parts that were lying around at Numatic. The head has a different motor inside to which it should have and the base again is different.

@TommyCullen-VacuumConnisour

7 ай бұрын

2003

It’s from 2004 or 2003 or 2005

@christopherinteriors6521

2 жыл бұрын

If you are going by the label on his head yes. He has had a replacement plastic head a few years ago as the previous one had some damage. The internals are older apart from a new old stock motor. Henry says thanks for pointing that out though, he likes to feel younger. 😂

@christopherinteriors6521

2 жыл бұрын

@Numaticfan08 the plastic casing is from around that time but the internals are much older. He had a nasty bump on the head.

@christopherinteriors6521

2 жыл бұрын

@Numaticfan08 If you check my newest video - episode 2, towards the very beginning you will see than he is no longer Henry either. He has been renamed!

@Mr_D2_1004N

2 жыл бұрын

​@@christopherinteriors6521 including the switch as the button style switch was introduced in 2002

If you use it without a bag you will shorten the life of the motor

@christopherinteriors6521

Жыл бұрын

definitely. I see so many people doing this.

What adaptors do you recommend for connecting the henry to the different size tool dust ports

@christopherinteriors6521

Жыл бұрын

Personally I make my own but I have just added a link in the description to one that my friend owns. They are highly recommended.