Love the video. Great to see there is up grades for these machines as I have just recently purchased my own!

@d4rkst0rm16

3 жыл бұрын

ive just gotten one myself recently. what sort of upgrades have you done so far?

What is the max voltage coming from the power supply at full speed? Did you adjust the small potentiometer on the circuit board to limit the max voltage?

Thanks a well made video however I do not like the doorbell sound effects

@cosmochannelvideo

5 жыл бұрын

I apologize for the delay in replying but the message saw it as spam. I'm sorry you don't like it. I'll see to it that I change it! Thanks for the comment

@tahustvedt

3 жыл бұрын

@@cosmochannelvideo I agree. Great video, but the doorbell was annoying. :)

@markgilmore2017

3 жыл бұрын

Agreed, I accidentally fired my butler for not answering the door!

I've just installed the same spindle on my 3018 machine and found that there's just too much play along the X axis, maybe because of the added weight in the Z axis assembly. I'm confident that replacing the rails in the X axis with fully supported ones will solve this problem, though.

@cosmochannelvideo

4 жыл бұрын

it's true. with the extra weight the movement is excessive. let me know if you solve and what you use. thank you!!

@jasonnayman6409

4 жыл бұрын

Jônatas Rech I just installed the same spindle. How did you weight issue?

@System-1541

2 жыл бұрын

Roger Webb shows how in this video: kzread.info/dash/bejne/pqGE2rl6ZsaWoMo.html

Ya solo ver lo que se menea cuando cambias la punta.... En fin, empieza a ahorrar para algo más rígido.

More vids on this! I would like to se if it can mill brass. Im thinking of buying this machine and upgrade it like you did and cut parts from 1mm brass sheets. Nice vid!

@cosmochannelvideo

5 жыл бұрын

Hello. thanks for the comment. I will definitely make more videos on CNC as soon as I learn how to use it! I'm sure you can cut brass even thicker than 1 millimeter.

@cosmochannelvideo

5 жыл бұрын

This CNC can give great satisfaction if properly adjusted.

@MyllerSWE

5 жыл бұрын

Awesome!

@Preyhawk81

3 жыл бұрын

i think you can cut steel if you dont do it to fast and only 0.5mm per turn.

Hello sir. Congratulations on this well presented topic. I took advantage of your link to order the set, which I received. I have a doubt, how to select, 110v or 220v. Could you enlighten me on this point. Thank you in advance and good luck. p.k.

HI. Nice clean build. Just finshed my cnc. Have a Look on my machine during engraving.

@cosmochannelvideo

4 жыл бұрын

thanks a lot .. i will!

WAOUW the quality of your video is excellent , can you tell me what model camera you use ? thank you

@cosmochannelvideo

4 жыл бұрын

Thank you so much. I use a one plus 5t smartphone

Be aware that the holes are exactly the same size as the bearings so if you have calibrated your printer too well it won't be a good tight press fit

bye, congratulations! beautiful update and a great video, I have just bought the same cnc, I'm just starting out, but I'd like to replace the motor like you did, but I'm afraid of not being able to make electrical connections, it would be possible to know how they do, thanks, congratulations again 😁

@cosmochannelvideo

5 жыл бұрын

Hi, there. If you have a little manual skill is not difficult. The electrical connections are very simple. The motor is not connected to the motherboard of the cnc and starts and adjusts manually. You can put a relay on the output that powers the old motor on the motherboard that closes the contact and starts the motor. However, the speed adjustment remains manual via potentiometer.

@stefanoromani7482

5 жыл бұрын

@@cosmochannelvideo thank you so much

@grandpaben5789

4 жыл бұрын

@@cosmochannelvideo Hi sorry i must have missed a few steps ! the connections are simple IF you have done it before ? What is the relay you mention sorry but it does not make sense ? All i see in the video is the power supply (I presume) taken from the old motor fixed to the new motor and then two wires (I again presume taken from the glb board (woodpecker board) this is put into the new power control unit into the motor terminals (with pot fixed to) BUT where does the power come from to power the new box ? ie connections to box go (on /off - motor - power) so where does this relay fit you mention ?

@grandpaben5789

4 жыл бұрын

@@cosmochannelvideo as clear as mud ? what is the relay you talk about ? two wires from original motor goes to new motor, two more wires from the old gbl (woodpecker board) fixed to the motor on the NEW box so that leaves two connectors still not used on the NEW box for power ? what is the relay for and where does it come in on the video ? need to spend less time with the music and more time on the explanation of what you are actually doing.

After install this thing, can I control spindle speed by program via gcode, or only manual speed adjustment ?

printing that shit now, thanx bro

@bblloobb1000

4 жыл бұрын

can tell how is it, is it enough strong, to hold stronger motors

@ronniepaulinc

4 жыл бұрын

@@bblloobb1000 yes it is... I modified it on my thingiverse tho.. I like to buy bolts by the pound so I did away with that metric crap. www.thingiverse.com/thing:3876546 Works great in holding the spindle but the machine could use some beef with the upgraded spindle!

To reduce the movement of the z carriage, use a bracket with a v roller mounted to the top of the carriage so the v roller travels in the groove of the 2020 horizontal bar.

@adrianharrison5208

4 жыл бұрын

thanks for the idea, i think ill try that on mine

You should not solder on a crimp. The solder stiffens the wire and makes it more susceptible to breaking. Just ensure that there is a match between wire size and crimp, and also use a good crimp tool. Furthermore, I recommend you use ferrules to terminate your wire instead of tinning the ends - the solder deforms over time and the wire becomes loose in the terminal. Thanks for sharing your project.

@cosmochannelvideo

4 жыл бұрын

Thank you for your invaluable advice! You never stop learning!

I see that there is 48v and 100v spindles with the same watt. What would be the best of is the same?

the use of a spring clutch without thrust bearings is unacceptable - it gives additional play, although it reduces vibration

Hi , If I have understood well ( you didnot show it) you control the spindle speed using the potensiometer. Correct? Is there a way to control the speed of the spindle Through GRBL? If you know can you show me how? George

This a great inspiration and help thanks. The spindles are the weak link on these small CNCs the upgrade is realistic and appropriate. Even if you don’t have a 3D printer you can order the part to be printed and delivered via Thingiverse.

@cosmochannelvideo

4 жыл бұрын

on Facebook there are many press groups. join a group in your country and ask them. often you find people near you who in exchange for a beer print it out for you.

Hello, I also have such a motor (48V). It was working before, but yesterday, while scraping wood, the motor had a hard time and suddenly stopped. Now it doesn't work at all. I measured it with a multimeter. There is electricity (48V) at the output of the PWM driver and the positive and negative terminals of the motor are powered, but the motor does not move. What do you think might be causing the problem?

Is the bell on the end of the motor a flywheel(mass) or is it some sort of fan?

Good

For the excessive play in the axis, could an elastic band or bands be attached from the bracket holding the motor to the top of the stepper motor to take the excessive play away? Like a damper?

@cosmochannelvideo

4 жыл бұрын

I just uploaded a video on how to solve the problem!!!! kzread.info/dash/bejne/ZKuhw65rc6m-hqw.html&t=

What exactly would this upgrade be useful for?

Nice! How much better is the new spindle?

@cosmochannelvideo

5 жыл бұрын

Surely the spindle does not vibrate and turning faster results in a faster and cleaner cut. The motor weighs more and therefore the speed of the movements must be lowered. However, excellent engine!

The wiring part of this video was kind of confusing. Could you make a more detailed video on wiring??

@jasonnayman6409

4 жыл бұрын

Yes, could you redo how you did the wiring? I have the bracket and spindle installed but you lost me on the wiring part. Thanks!

@grandpaben5789

4 жыл бұрын

@@jasonnayman6409 Yeah i was just wondering the same ? By the looks of it the original power is just attached to the motor but where does the second set of wire's come from that he attached to the motor side of the new new power unit ? is that from the original woodpecker control board ? If so that is the controller wires, but the question remains were does the power come from that goes to the new unit ? (the inputs that say on/off - motor - power) ? or does that have a separate power supply ?

@grandpaben5789

4 жыл бұрын

Yeah i was just wondering the same ? By the looks of it the original power is just attached to the motor but where does the second set of wire's come from that he attached to the motor side of the new new power unit ? is that from the original woodpecker control board ? If so that is the controller wires, but the question remains were does the power come from that goes to the new unit ? (the inputs that say on/off - motor - power) ? or does that have a separate power supply ?

@chrisallen5237

4 жыл бұрын

I'm watching this for the wiring. Where did those two wires for the power supply come from?

@tusla8979

4 жыл бұрын

Same question. Are you using an external Power supply for it? I am doing the upgrade on a 3018 pro version and the power Output ist 24V. Not enough for that spindle

Thank you for your video. Can you tell me specifically how to connect the control board, power supply, and spindle? If you don't mind, can you explain it in a picture?

@cosmochannelvideo

4 жыл бұрын

The spindle is controlled manually. It is not connected to the controller

@seongminlee-wz5bg

4 жыл бұрын

Cosmo Channel Ok,Thank you

hi thank you for your video. Sorry what are your vcarve /drill that you are using un the video ? a link ?

Hello! I bought the same engine as you. But unfortunately I didn’t pay attention and bought ER11. What do you think is possible to replace this engine ER16. Can ER11 be taken off? Thanks.

Does this upgrade mean that you have to use two separated AC power source? I have the same kit

@n.r.4269

2 ай бұрын

Yes but 48 DC

Nice job!!! I have the same CNC machine....pumped up with limit switches...Z probe...learned a lot with it. Just a question: how is your spindle turned on?

@cosmochannelvideo

5 жыл бұрын

Hi Adrian. thank you!. I'm looking for ways to start it via the motherboard but for now I turn it on and set it by potentiometer. I'm also looking for information on the limit switches and z probe.

@dmaher2007

5 жыл бұрын

@@cosmochannelvideo I have a sheet drawn up for connections on this CNC if you need it, I can email if you like?

@cosmochannelvideo

5 жыл бұрын

@@dmaher2007 Of course it is! Thank you so much! cosmochannelvideo@gmail.com

@dmaher2007

5 жыл бұрын

@@cosmochannelvideo sent 2 drawings, Check your email, Cheers.

@privatebubba8876

5 жыл бұрын

Cosmo Channel could you do a video with the limit switch upgrade? I have the limits and I'm pretty sure of what pins to use, but it's nice to have verification. CNC without home is a big PIA. I'm putting together a 50x60 5000 watt laser right now. I'm a newb so any help and suggestion are welcome.

So,how are you powering the spindle board?I just got one of these(with Mach3) and I'm confused(I'm in US,btw),do you just put 110v to the power terminals?Don't wanna blow it up,lol..Thanks for sharing!

@cosmochannelvideo

4 жыл бұрын

Hi, there. I connected the 220V to the input of the motor power supply. The motor is powered at 48v and regulated by a potentiometer. Unfortunately with this configuration it is not possible to manage the speed with the motherboard of the cnc.

@Bowtie41

4 жыл бұрын

@@cosmochannelvideo Thanks for the rapid reply!That at least let's me know how the supply is powered,I can figure out the Mach3 control later.Best Wishes1

Anyone know where i can get a 3d printed spindle mount from to fit machifit spindle motor from in the uk please

11:25 so mutch wobling can this thing do accuracy of 0.1mm?

@cosmochannelvideo

4 жыл бұрын

in the next video, I solved the problem of accuracy.

Where did you bought spindle extention wires.Are you used 18 gauge silicon red and black wire for extend the spindle wire.Which wire are you used for power.where did you bought it.

@cosmochannelvideo

3 жыл бұрын

18 awg is perfect

Hi, can you tell me how to remove the ER 11, not just the collet, from my Spindle 500? A thousand thanks.

சூப்பர்

I need a spindle to make a CNC drill to drill 4mm holes... in about 2.4mm thick aluminium U channels could you recommend something?

@cosmochannelvideo

4 жыл бұрын

what I've mounted on this cnc can definitely be your thing.

Good video, well done but you didn't give us a "worth it / not" rating. Also there seemed be a lot of play in the mount for the Z axis.

@cosmochannelvideo

4 жыл бұрын

Hi! For me it's worth it if you want to make faster cuts. For stability watch the next video where I solve the problem. I feel very comfortable.

I have a new 500w, when using it at more than 50% for 30 minutes it heats a lot, is it normal? Will it be a bad voltage? or it will be damaged

@cosmochannelvideo

4 жыл бұрын

Bye. It depends on what you mean by heating a lot. you don't have to burn. if it's hot it's fine.

@grandpaben5789

4 жыл бұрын

Does the fan on the top spin ok ? sometimes thy clog up with dust and debris in the fan encloser.. BUT it should not get overheated a little warm maybe. You could drop the speed down on the motor and on the x/y speed of the cut that will help, it may take longer but will be safer on bit cuts.

Hello.I am wondering about one thing.You disconnect original motor from the cnc board isnt it? And than you connect two wires ded and black ,one side to controler and other side to the spindle motor?

@cosmochannelvideo

4 жыл бұрын

Hello. I disconnected the original spindle from the card. the new spindle cannot be controlled by the CNC card and therefore I connected it to its power supply

@katsuragisan1

4 жыл бұрын

@@cosmochannelvideo did you connect limit switches to your board.I have Eleks Mana board and it us slightly different than original..and i am wondering how to connect them

@tusla8979

4 жыл бұрын

@@cosmochannelvideo Great! Please provide this information in the description of your excellent Video!

Is it possible to adapt the PWM speed control instead of having to use a manual knob?

@cosmochannelvideo

4 жыл бұрын

absolutely yes

Do you plan on upgrading the stepper motors, If so what will or would you use?

@cosmochannelvideo

5 жыл бұрын

I still don't have any idea what to put on. :-)

@dmaher2007

5 жыл бұрын

@@cosmochannelvideo For my upgrade I have ordered 800mm Length 2020 T-Slot Aluminum Profiles Extrusion Frame for 3D Printer CNC x 6..........800mm x 8mm Linear Rail Shaft Rod with Bearing Guide Support and SCS8UU Bearing Block x 4........T8 800mm Stainless Steel Lead Screw Set with Shaft coupling and Mounting Support x 2 Plus the the spindle motor you shoewd on this video, and the spindle upgrade thingiverse, I ordered that a few minutes ago, so I should have an 800mm x 800mm cnc, hope it works? time will tell.

@cosmochannelvideo

5 жыл бұрын

@@dmaher2007 So much stuff! You're practically building a new one! That's great! Keep me informed! I want to see the photos!

@niranthbanks3595

5 жыл бұрын

Dave Maher If I may ask, from where did you order these? I’m keenly interested in your results.

@cosmochannelvideo

5 жыл бұрын

@@niranthbanks3595 Hi, there. In the description of the video you will find all the links

The only reason I would upgrade the spindle is if I wanted more confidence for the machine to mill aluminum.

@kimhansen6384

4 жыл бұрын

Yes, but the engraving did not turn out very well.

@cosmochannelvideo

4 жыл бұрын

Bye. I just made some changes that solve the movements that made the spindle to the too much weight. Soon I'll put the video. Now the engraving is much more accurate. I am waiting for an aluminum cutter to do a test of engraving on aluminum.

Hi great video. I have problem. Identical equipment CNC3018, the Y axis (that of the plane on which supports the objects to be processed), during the work you hear a tac and shoot losing the path with the x axis. I changed the complete bar of bronze spiral, but I haven't solved it. Do you have a suggestion? Thank you very much! - Do you also have a chance to explain how you carry out the project with the writing?

I am thinking of doing this exact upgrade. Is it worth it? What are the biggest advantages?

@cosmochannelvideo

4 жыл бұрын

works very well especially for very small engravings at low speed. but I would mount it on the cnc 3018 pro which is much more stable.

make a video of it milling aluminum not just engraving

@therealsourc3

4 жыл бұрын

Also he is using a wood engraver on aluminium, you can see the tip got frayed at the end.. Using a tiny ball end mill would yield better engraving quality if it's only for text.. and that's pretty cheap - you can get them on ebay for under 5 bucks with free shipping..

Ciao! non riesco a capire da dove hai preso l'alimentazione per l'alimentatore :D mi sono perso qualche passaggio? Grazie e complimentiiii

@cosmochannelvideo

2 жыл бұрын

Quel alimentatore ha una semplice spina da 220v

Nice video, very educational. I have just recently purchased my own and i have negative milling results, i try to reverse without success. I match appreciate your advise.

@vicomedia1

4 жыл бұрын

Nice video, very educational?? there are no spoken words!!!

@dimitrisnydriotis

4 жыл бұрын

@@vicomedia1 I do not trace any of your videos.....

@cosmochannelvideo

4 жыл бұрын

There was little to say but a lot to show for it... I don't like to waste words 😂😘

There is something I don't understand, I hace a machine like that, but the spindle is 775 and you are upgrading it with one of 500, could you explain me that please?

@cosmochannelvideo

4 жыл бұрын

Hi, there. The original motor is 80w maximum 9000 rpm. The one I mounted is 500w maximum 12000 rpm without vibration.

Buongiorno e complimenti, stampato in ABS oppure PLA ?

@cosmochannelvideo

Жыл бұрын

Grazie! Pla

Has you some problema of interference of spindle? When I turn on the spindle, my stepper motors go crasy.

@ripmartin1673

4 жыл бұрын

what are you using for your controller? you may need to check the type of gcode your using

@tchelas2

4 жыл бұрын

Rip Martin , Im using a arduino + cnc shield v3. The Gcode is generated by Artcam 2008. Extension of file is .tap

@cosmochannelvideo

4 жыл бұрын

Hi! I have never had interference problems. You could shield the spindle's power cord.

Ciao, grazie per la pubblicazione di questo video, vorrei anch'io fare la modifica sul motore ma mi sono fermato perchè non trovo più il file per la creazione in 3D del nuovo supporto, per caso riesci a farmelo avere e/o metterlo in linea........ grazie la tua pazienza e disponibilità

Hammering bearings in? No wonder the axis locked up. If you dont have a press, you chould have pulled them in with a length of stud (threaded bar) These cheap machines can be so much better if assembled carefully - 3D printers are a perfect example

@cosmochannelvideo

4 жыл бұрын

You're right. I admit I made a mistake using a hammer to insert them. In the video I posted a while ago where I change these bearings I used a vice to push them in. Thanks anyway for the message!

Is the spindle speed still controlled by the mainboard?

@cosmochannelvideo

4 жыл бұрын

no it is controlled by a potentiometer

How much would you charge to make me one of those mounts on your 3D printer?

upgrade to this spindle can i cut carbon fiber sheet with this???? thanks...

@cosmochannelvideo

5 жыл бұрын

with the right cutter of course!

Can you add some more aluminum tests?

@cosmochannelvideo

5 жыл бұрын

I'm gonna make a video soon. For now I have problems with the z-axis (it's not fluid and freezes) and so I'm waiting for spare parts.

@mikesnapper9001

4 жыл бұрын

@@cosmochannelvideo Have you managed to solve the z axis wobble? I want to buy the same CNC and upgrade it with the same motor actually, but z axis wobbling would be pretty bad, since it means I wouldn't be able to do precise detail work. What part of the z axis is causing the wobble? Is it the 3d printed plastic motor holder? if so, then that is good, since you can just print a better one, but if the wobble is coming from the metal parts, like large tolerances in the aluminum rails or something like that, then that would be very very hard to fix without basically replacing half of the entire machine

@melvyniandrag

4 жыл бұрын

@@cosmochannelvideo update please!!

hola buen dia, tengo un problema mando a fresar y todo empieza bien pasando de los 10 min funcionando de repente se detiene y ya no avanza pero el spindle sigue funcionando el problema es que los motores dejan de girar, tiene alguna soluciona ello?

@cosmochannelvideo

5 жыл бұрын

Hi, there. Mine works perfectly. It could be your motherboard that has some problem. www.banggood.com/custlink/GGDK9GB8dl

the size of the model is wrong brandon75f, did you have to grind the axles?

@cosmochannelvideo

4 жыл бұрын

The dimensions are right. I printed it the way it is on tinghiverse and edited it without changing anything.

A minor upgrade. If you are going to this amount of effort then it would have been better to have addressed the issues of having the spindle mounted so far away from its supports - this gives unacceptable flex in stock configuration. Im about to add this type of spindle to mine and hopefully will address these issues...

Great video but the sudden ear obliteration was uncalled for... :P

@cosmochannelvideo

4 жыл бұрын

thanks a lot

Please narrate your videos instead of the background music. It's much more informative to have someone explaining the steps over the music you use. Also, text overlay would help as well.

@cosmochannelvideo

4 жыл бұрын

hello and thanks for the comment. in the first videos I didn't speak because I don't speak english well. now I started commenting them in Italian but adding subtitles that can be translated.

How to connect wiring from spindle and power source to the box?

is the replacement part enough strong to hold stronger motor like in video

@cosmochannelvideo

4 жыл бұрын

The support holds up easily.

@bblloobb1000

4 жыл бұрын

@@cosmochannelvideo ty

Ciao, bel inanzitutto! Ti volevo chiedere una cortesia, mi sai dire come gestire il mandrino attraverso la scheda grbl versione 3.4? Grazie

@cosmochannelvideo

3 жыл бұрын

Ciao! Con questo mandrino non puoi gestire la velocità via controller ma solo manualmente

@beppuzzogiannetti7110

3 жыл бұрын

@@cosmochannelvideo non c'è un modo ( magari con un relè ) di pilotarlo tramite l'uscita della scheda, trasformando il segnale pwn?

@cosmochannelvideo

3 жыл бұрын

puoi mettere un relè sul controller che accendere o spegne il mandrino ma la velocità sarà comunque regolata a mano.

That spindle-motor driver is crap. When it dies you should open it up and see what they did to it in china. Mine had all sorts of trace ground off and rerouted with hokey wiring, and giant globs of solder. Frankenstein boards. I got sick of the noise, so I replaced that with the brushless 500W.. Soooo much better! Watch out for EMF too! It can cause real issues with losing step.

@sticky_ricebowl

2 жыл бұрын

yup I FELT that EMF..... literally shaking my stepper motors and now I need to buy a new spindle set

Have you upgrade the grbl software

@cosmochannelvideo

5 жыл бұрын

I haven't updated anything yet, but I plan on doing so soon.

Great video, but the music could go

BOA NOITE, A CNC 3018 TAMBÉM CORTA AÇO ?

@cosmochannelvideo

Жыл бұрын

con esta máquina no se corta acero a menos que tenga velocidades extremadamente lentas con muchas vibraciones y poca precisión.

Io ho la tua stessa combinazione, però mi succede che quando aumento il potenziometro del mandrino (dal 50% in su) la macchina si blocca buttando via ore di lavoro, per caso succede anche a te? Io di elettronica non ci capisco molto ma sembra un problema di interferenze elettromagnetiche

@cosmochannelvideo

3 жыл бұрын

Ciao! Hai i limit switch abilitati?

@claudiograndi7657

3 жыл бұрын

@@cosmochannelvideo per abilitati non so cosa intendi, però i limiti switch ce li ho ma sono scollegati perchè mi davano problemi

@cosmochannelvideo

3 жыл бұрын

hai disabilitato l'hard limits sul controller tramite comando grbl?

Will it mill soft metals like aluminium? (with like a small end mill, not engraver)

@cosmochannelvideo

5 жыл бұрын

Probabilmente ne avrò bisogno per fresare alluminio o rame, ma devo ancora capire qual è il miglior consiglio da usare.

Hi. Is there any one or any place I can get this bracket printed as I have not got 3D printer? Help PLEASE!

@cosmochannelvideo

4 жыл бұрын

Hi, there. Look for some group on facebook printing 3d and look for someone who lives near you who can print it for you. Or some online 3d printing service.

@radoslawsosnowski3326

4 жыл бұрын

@@cosmochannelvideo Thank you.

What software did you use to run the machine

@cosmochannelvideo

4 жыл бұрын

grblControl_0.8.1 was included in the package.

@mr.linskie8829

4 жыл бұрын

@@cosmochannelvideo okay, Thank you sir

@cosmochannelvideo

4 жыл бұрын

@@mr.linskie8829 thanks to you.

11:24 Leng, mint bűzakalász a szálben, egyáltalán nem stabil!

Оно же всё болтается... Спасибо за видео - понял что это пустая трата средств.

@gb614erg

5 жыл бұрын

Я вот тоже посмотрел - всё болтается. Надо раму апгрэйдить, и только потом мотор

@cosmochannelvideo

5 жыл бұрын

You're right. The frame suffers with this additional weight. Account to change the frame. For now, I'm just milling at a reduced speed.

UPGRADE great, but your cnc is small, that for make handmade

Ciao posso mettere del grasso nella parte meccanica della cnc ?

@cosmochannelvideo

4 жыл бұрын

Si purché sia grasso siliconico. Mettine poco ..

Get rid of the music, it's unnecessary and I would have the spindle mount CNC,d out of aluminium along with it's mount, it won't cost much as the files are free to download, more info on wiring should have been clearer as there is 220v at the start of the supply, people tend to forget this , while the board is low voltage the power supply will kill you.....

trovato, grazie.... ora passo alla modifica...

@cosmochannelvideo

4 жыл бұрын

Perfetto! Comunque il link è nella descrizione 😉

@MrGiaoggi

4 жыл бұрын

si l'ho visto dopo..... stiamo combattendo con una cnc 2417 che non riusciamo a farla partire, abbiamo fretta di realizzare dei pcb e così abbiamo acquistato questa 3018 sperando di risolvere il problema, a marzo dobbiamo esporre un simulatore di volo.....

Now what will you brush your teeth with? :)

Hello How can I get / order spindle mount to upgrade?

@cosmochannelvideo

4 жыл бұрын

you can buy it on the site banggood or amazon by following the links below the video

@tourwithme

4 жыл бұрын

@@cosmochannelvideo I need only Clamps for my cnc3018

Hello! sorry but how do i connect the kit on the 3018 pro? i can't understand well from the video, is some other component needed? 

E' possibile utilizzare il tutto anche sulla versione Pro?

@cosmochannelvideo

4 жыл бұрын

L'asse z dei due modelli è uguale quindi si potrebbe fare..

Hi. your engine is also very hot?

Nice video for upgrading...might want to skip the inane background music next time, less is more. :)

у cnc 3018 маленькая жесткость, из за этого нет смысла его апгрейдить более мощным двигателем

@cosmochannelvideo

5 жыл бұрын

Hello, Constantin. I have to agree. I'm noting that actually the weight of the new engine makes a lot of resistance in the small movements. I'm thinking of improving all the bearings.

@constantinzzz8562

5 жыл бұрын

@@cosmochannelvideo I also have a CNC 3018. When I bought it and tried it, I also had thoughts about its refinement. But bearings alone cannot do, this engraver (it is an engraver and not a machine tool) has thin guides. After replacing the guides with thicker ones, another problem arises - the effect of the rigidity of the structural elements on the result. Therefore, I went the other way. I ordered the components from the shafts of 16 mm, the bearings printed on the 3D printer and now I assemble the frame of the future cnc from ldsp. And the engraver will remain an engraver to let him perform his tasks - milling of printed circuit boards and small art bas-reliefs. LDSP - laminated chipboard

@constantinzzz8562

5 жыл бұрын

just in case the original text У меня тоже чпу 3018. Когда я его купил и опробовал тоже возникли мысли о его доработке. Но одними только подшипниками не обойтись, у этого гравера(это именно гравер а не станок) тонкие направляющие. После замены направляющих на более толстые, возникает другая проблема - это влияние жесткости конструктивных элементов на результат. Поэтому я пошел по другому пути. Заказал комплектующие из валов 16 мм, подшипники напечатал на 3д принтере и собираю сейчас из лдсп станину будущего чпу. А гравер останется гравером пусть выполняет свои задачи - фрезеровка печатных плат и небольших художественных барельефов.

@jw200

5 жыл бұрын

@@constantinzzz8562 Видео будет?

@constantinzzz8562

5 жыл бұрын

не созрел еще для видео на ютуб

What bit did you use on the wood please?

@cosmochannelvideo

5 жыл бұрын

Hi, there. I used the 30° bit of this great kit. www.banggood.com/custlink/KvmvcBVjIF

Too much movement in z axis :-(

@cosmochannelvideo

5 жыл бұрын

Yes, you're right. I'm thinking about restoring the original engine.

@adrianharrison5208

4 жыл бұрын

@@cosmochannelvideo did you do this?

ciao siccome ho acquistato il motore del video pero non dispongo di stampnte3d non e per caso che potresti fornilo tu naturalmente pagherei la manifattura . Grazie

@cosmochannelvideo

3 жыл бұрын

Ciao Giovanni. Per ora sono senza stampante.. sono in attesa di una stampante nuova (ne farò un video). Se chiedi nei vari gruppi di stampa 3d su facebook magari trovi qualcuno vicino a casa tua

@giovannipanci9413

3 жыл бұрын

@@cosmochannelvideo sai lo ho fatto stampare da una ditta di milano ma quando mi e arrivato mi sono accorto che era fuori squadro ,50 euro buttati

@cosmochannelvideo

3 жыл бұрын

Fuori squadro per colpa loro?

@giovannipanci9413

3 жыл бұрын

@@cosmochannelvideo certo io ho mandato disegno che hai postato tu ,e a te andava bene giusto????

@cosmochannelvideo

3 жыл бұрын

A me è andato perfettamente fin da subito.. Mi dispiace non poterti aiutare.. se aspetti una quindicina di giorni potrei stampartelo io.. Purtroppo la mia l'ho prestata ad un amico (che la comprerà) ed io sono in attesa di una nuovissima Creality Ender 3 V2

Hello, My 3018pro has stop running program, com port has disconect bitwin running, Plz tell me what is problem

@cosmochannelvideo

4 жыл бұрын

There could be a thousand things. Overheating of some defective component? defective cable? energy saving activated on the pc? If you find the problem please let me know!

@HunTomiBp

4 жыл бұрын

Ehhez a motorhoz egy nagyon rossz minőségű vezérlőt gyártottak! Én úgy oldottam meg, hogy cstlakoztattam a földhöz a vezérlő dobozát, a cnc vázat, a motor burkolatát és tengelyét is. Utána már nem szakadt meg az USB kapcsolat. Z-prob esetén használj galvanikus leválasztást például opto-csatolót, külömben kiég a cnc vezérlő!

@mierzhen

4 жыл бұрын

@@cosmochannelvideo Had the same problem with the 3018pro (factory stock), where each time I run the spindle, do a basic G1 movement or anything of such. Suddenly, program loses connection with the mill, saying "device is not responding", turns out the USB-A to Mini supplied was garbage. Found a spare usb cable, hasn't given me any problems like that for now.

Hi, can the cnc cut aluminum of thickness 3-4mm?

@cosmochannelvideo

5 жыл бұрын

Hello CyClistFpV. I'm sure that with a good 2 cutting edges cutter and several passes you can safely cut soft metals up to 5mm thick. If you haven't done so yet, sign up for my channel!

@lahbibnabil1446

5 жыл бұрын

Cosmo Channel It will be interesting to see that.

I am confused about where the wires at @10:27 come from

@cosmochannelvideo

2 жыл бұрын

Hello. those cables come from the spindle and connect it to the power supply

@mokolocomadafaka

2 жыл бұрын

@@cosmochannelvideo Thanks. Second question is regards to the actual power input. What are you using? just plugging into wall or using a power supply? I am about to set it up direct to wall and taking extra safety measures by 3dprinting a custom case (So the power supply is not accessible at all). So this is not connected to the CNC PCB right? I have to basically turn it on before the program runs for cutting? Thanks

@cosmochannelvideo

2 жыл бұрын

The spindle is powered only by its power supply connected to the power outlet. Before starting the machining you have to manually turn on the spindle. You could put a 24V relay on the spindle connector output on the controller which will power the spindle.

@mokolocomadafaka

2 жыл бұрын

@@cosmochannelvideo Thanks

Rpm of moter?

@cosmochannelvideo

4 жыл бұрын

3000-12000r/min

You have no anti-backlash nuts...

Hi is it brushless ..!!

@cosmochannelvideo

5 жыл бұрын

yes!!

stupid fucking bell disturbed me

Ciao Simone ho acquistato il mandrino da 500 watt per la 3018 e anche per farla più grande 3040 vorrei avere uno schema per poter montare il mandrino esattamente giusto per nn fare danni poi ho preso anche l'asse z e anche una scheda madre per poter montare il mandrino da 500

@cosmochannelvideo

2 жыл бұрын

Ciao. Sono contento per te per tutti gli acquisti. Che schema intendi?

@pasqualebasile3318

2 жыл бұрын

Simone mi interessa lo schema per poter montare il mandrino alla scheda se mi dai l'email ti mando quello che ho comprato

@pasqualebasile3318

2 жыл бұрын

Purtroppo mi spaventa il problema di danneggiare il materiale che ho acquistato dato che nn puoi per cellulare almeno aiutami te lo chiedo per favore

@cosmochannelvideo

2 жыл бұрын

Questo mandrino non lo puoi collegare al controller. Lo accendi e regoli manualmente

@pasqualebasile3318

2 жыл бұрын

Ma se mi dai qualche indicazione per favore come montare elettricamente mi saresti di aiuto dammi l'email che ti mando la scheda che ho acquistato

Unstable. I see the table is vibtating.

How much this cost to india...

@cosmochannelvideo

4 жыл бұрын

There's a link in the video description. Check it out from there.