Your video is very helpful, thanks. Ray from Germany

Very helpful advice, thank you! Placing my order now

@VacuumPressingSystemsInc

3 жыл бұрын

Glad to hear you found the video helpful!

Very informative video. This man knows his business. I'll bet he's done more bench pressing than Arnold Schwarzenegger. Get it?

@VacuumPressingSystemsInc

3 жыл бұрын

Glad to hear you found it informative. I shared your joke with the guys around the office and we had a good laugh, thanks.

@andrerogers9961

Ай бұрын

Badum, tish!

For fast operation I'd use a shop vac and a small piston pump in parallel with independent valves. I'd evacuate most of the air rapidly with the shop vac first. Then I will bring down the vacuum with the piston pump to a very low level. The piston pump does not remove most of the air.

Which one do you recommend for thermoforming solid surface? Do you have a model with external controller so the pump can be hidden away and operated via an external controller.

@VacuumPressingSystemsInc

4 жыл бұрын

With thermal forming you want a pump that draws down fairly quickly before the material cools too much. I would suggest our HiFlo industrial 10cfm pump as your first choice and the Professional 6cfm pump as the second choice. If you would like to discuss this further feel free to give us a call at 800-382-4109

Are these safe to use for a vacuum chuck on a wood lathe? I’m concerned the auto shutoff might kick in at some point and send the piece flying off.

@VacuumPressingSystemsInc

Жыл бұрын

When using a vacuum chuck, we recommend running the pump continuously.

What is the duty cycle on these units? I have an industrial hi-flo unit I'd like to use for workholding on my milling machines, but I'm worried I will burn it up with extended use.

@VacuumPressingSystemsInc

3 жыл бұрын

All of our units are thermally protected so they will shut off before any damage is caused to the motor. If you plan on running your unit for extended periods of time in the "continuous run" mode we would recommend removing the cover from the unit to allow for additional air circulation.

@OakwoodMachineWorks

3 жыл бұрын

@@VacuumPressingSystemsInc Thanks for the response!

could you use these pumps to create a vacuum chamber (for impregnating wood with resin)?

@VacuumPressingSystemsInc

2 жыл бұрын

yes, you can use our pumps for degassing.

Hi there.. Do you provide your pumping units with a 220/240v system?

@VacuumPressingSystemsInc

3 жыл бұрын

Yes, we carry all our units in both 120V and 240V.

will your smaller Vac pump work with a woodworking lathe Vacuum Chuck?

@VacuumPressingSystemsInc

2 жыл бұрын

it will work but the low CFM flow may not provide enough holding power. Bigger pump would be better for lathe work

Can you use this vavuum pump with Stainless Steel Vacuum Chamber (5 gallon) for Stabilizing Wood?

@VacuumPressingSystemsInc

2 жыл бұрын

Yes you can, though a scientific vacuum pump might do the job a little bit better.

Have you had anyone use your pumps for composite work?

@VacuumPressingSystemsInc

2 жыл бұрын

Yes. You may need to add an inline resin trap depending on your application. Feel free to call if you'd like to discuss further.

@RCCAD2VR

2 жыл бұрын

@@VacuumPressingSystemsInc Awesome! Thanks for the response. Thinking this may be the solution I've been looking for. May feature it in my upcoming build videos if I go ahead an purchase one. Thinking the Compact 150 VacuPress would do the trick for my setup.

@VacuumPressingSystemsInc

2 жыл бұрын

@@RCCAD2VR You're welcome! We hope the Compact 150 fulfills all of your hopes and dreams!

Nice information. Sir suggest a vacuum pump for my chamber (size 7 feet*4feet) for pvc foil press.

@VacuumPressingSystemsInc

3 жыл бұрын

Without being familiar with your PVC foil press I cant be sure of the right pump for your application. I think just a continuous duty pump may be best for you press.

@3DMrSharmaji

3 жыл бұрын

@@VacuumPressingSystemsInc sir my work is vacuum membrane press for plywood routed door? Plz suggest me

@VacuumPressingSystemsInc

3 жыл бұрын

​@@3DMrSharmaji can you send information about the vacuum membrane press you will be using

@3DMrSharmaji

3 жыл бұрын

@@VacuumPressingSystemsInc sir you can search video to write"membrane door making process" on KZread

those uneven brackets in the fore ground are killing me!

@VacuumPressingSystemsInc

5 жыл бұрын

We appreciate your perfectionism and thank you, we got a good laugh out of this comment.

Nice explanation. Unfortunately the measurement units chosen are only used in one country in the world, the only one which has not completely wrangled itself loose from the former British Empire. Funny that the pumps themselves do use the SI system for pressure.

@VacuumPressingSystemsInc

4 жыл бұрын

Yeah, we Americans tend to think we're the center of the universe. If need be google can convert those numbers for you.

@4431charlie

4 жыл бұрын

@@VacuumPressingSystemsInc yes we are !!! Trump 2020

@jazzman1954

4 жыл бұрын

So how many seconds in a minute, minutes in an hour, hours in a day in Euro Heaven?

@jazzman1954

4 жыл бұрын

andy young Nope. Didn’t help.