Unboxing Mustang P-51 Rc Assembly Flight Test Volantex 768-1 750 mm Gyro Airplane Stabilized
Ойын-сауық
Mustang P-51D Unboxing + Assembly + Flight Test Volantex RC 768-1 750 mm RC Airplane RTF
►🏆 Online Shop Recommended : Affiliate link bit.ly/3eHKkPL
►📢💰 For Discount Coupons and Updated Offers Enter My Telegram Channel At The
Following Link bit.ly/3d3XT9V
Chapters
00:00 - 00:12 Preview
00:13 - 13:26 Unboxing + Assembly
13:27 - 14:33 Calibration
14:34 - 17:57 Flight Test
17:58 - 18:51 Photographic Book
#rcplane #Mustangp51 #Volantexrc
P.S.inquire before purchasing the aircraft from the National Civil Aviation Authority of your country to comply with current regulations.
Пікірлер: 170
Thanks!
@PassionHobbyRC
5 ай бұрын
❤❤❤
Product Link: ► Volantex RC 768-1 Mustang P-51D 750mm www.banggood.com/custlink/vD3ESzATki
Got mine! Thanks for the great assembly video :)
@PassionHobbyRC
3 жыл бұрын
thanks for the welcome message
I’ve got one of these and will be building in the New Year. I have the mini mustang too which is only 400mm. Great value I have to say and great flying too 🤩👍🏻
@PassionHobbyRC
3 жыл бұрын
thanks my friend deo welcome🤗
@knightrider3766
2 жыл бұрын
@@PassionHobbyRC hey, lol..you are very constructive...I have to rewind 5 times just to make sure iam caught up with your presentation...question, what channel are the transmitter..4ch..or 5ch??
Thank you Sir! Best Assembly Video!!
@PassionHobbyRC
3 жыл бұрын
thank you my friend dekl gradiot message a good day
Dziękuję za instrukcję☺ Pozdrawiam z Polski.
@PassionHobbyRC
2 жыл бұрын
dzięki, przyjacielu
Thanks for sharing, greetings from Mexico.
Ordered this plane and look forward to 'her' arrival! Got the smaller Mustang and the Corsair, very good value for money.
@PassionHobbyRC
3 жыл бұрын
excellent choice, I also have the smallest model I also made a video with all three Trojans T-28 Mustang P-51 Corsair F4U. I wish you a good day
@capnhardway
2 жыл бұрын
Same here, rebuilt both of them I've banged them up so bad, but so much fun and learning a lot in the process.
So was cog spot on with all stock setup,or did it need more nose weight? Thanks
Bellissimo questo aeroplano. Like 86,. Buone feste carissimo amico.
@PassionHobbyRC
3 жыл бұрын
Grazie amico mio , buone feste anche a tè.
had a time finding the 750mm...I finally found it on volantex euro, can't wait for it to come..
Wow amazing RC Flight 진짜 긑네주는 rc비행기네요!!!!
@PassionHobbyRC
3 жыл бұрын
🤭🤗🤗🤗🤗
cool assembly and flight
@PassionHobbyRC
3 жыл бұрын
Thanks my friend
Great video to help me assemble mine.
Nice looking little mustang 👍💯
@PassionHobbyRC
3 жыл бұрын
Thanks my friend
where did you get the extra 6 screws to attach the horns ha ha! (Your inventory showed 6 on the table but you installed 4 each on three horns, ha ha!) I'm assuming 2 per horn would have been sufficient?
Very nice plane my friend
@PassionHobbyRC
3 жыл бұрын
Thanks my friend
Looks a great model big like
@PassionHobbyRC
3 жыл бұрын
Thanks my friend
Looks nice!
@PassionHobbyRC
3 жыл бұрын
Ciao Nik speriamo di vederci presto 🤗🤗🤗🤗👍🏻👍🏻👍🏾👍🏾
Very cool p51 pretty nibble in air also 👍🏼
@PassionHobbyRC
3 жыл бұрын
Thanks my friend rc
I got mine but do I do about the propeller shutting off if I move up on the throttle fast. I’m scared it may cut out mid air and have to reconnect.
感謝分享,Thanks。
That plane looked so cool. And it looks like it flies very well.
@PassionHobbyRC
3 жыл бұрын
Yes Friend and an excellent plane with stabilization function, suitable for those who start flying for the first time
@RCsBigAir
3 жыл бұрын
@@PassionHobbyRC I would need the stabilization! 😁
Bro amazing Build , it looks Amazing and ill be the 2rd one out off the comments to say that was amazing smooth flying bro, it sounded so nice 👍. Really enjoyed every second 👍😁😎👍
@PassionHobbyRC
3 жыл бұрын
thanks my friend of the welcome comment
Hi Thank you so mach for all your videos... 🙂. Do you think i Can plug to this motor 3s 11.1v battery?
@PassionHobbyRC
Жыл бұрын
ZOP Power 7.4V 850mAh 2S 25C
@claudeladow2334
Жыл бұрын
Buy replacement esc from bang good, then can use 3s
Very nice brother. 👍 🇬🇧😀👍
@PassionHobbyRC
3 жыл бұрын
Thanks my friend
Bellissimo
@PassionHobbyRC
3 жыл бұрын
Grazie amico mio
Can’t find any model with this type of clear canopy, only the solid black ones
@PassionHobbyRC
3 жыл бұрын
you can try to do it yourself
Bonjour j'ai reçu ce modèle mais le ESC n'est pas fixé à l'intérieur. Avez-vous placer du velcro ou autre chose pour l'empêcher de bouger à l'intérieur? Merci pour ce vidéo très bien fait. ;)
@PassionHobbyRC
2 жыл бұрын
storno, comunque puoi usare anche un adesivo o feltro adesivo come hai detto tu. una buona giornata
@N2009D
2 жыл бұрын
@@PassionHobbyRC Cosa intendi con "storno", Non parlo italiano, quindi non capisco questa parola. traduzione automatica. Grazie
Excelente tu video; y viene incluido el Mando a Control con el avión?
@PassionHobbyRC
Жыл бұрын
yes
I've ordered, waiting on them to ship, not the fastest but they seem to eventually get it here .
@PassionHobbyRC
2 жыл бұрын
👋
happy Christmas 👍🎅🎄😊
@PassionHobbyRC
3 жыл бұрын
happy holidays my friend
Fajny ☺
@PassionHobbyRC
2 жыл бұрын
tak, jest pięknym modelem, ale zawsze miej oko na czas trwania beatu. Do zobaczenia wkrótce
Where can I find replacement parts that are in the US. Any information is greatly appreciated
@PassionHobbyRC
3 жыл бұрын
hello, on the banggood website. find the link in description below the video
@KnightsOutdoorAdventures
3 жыл бұрын
@@PassionHobbyRC thank you I appreciate it. Is that website trustworthy? I don't trust many websites
question...can I use the p51 mustang 400mm mini transmitter on this p51 mustang 750mm RTF warbird as well?
@PassionHobbyRC
2 жыл бұрын
I don't know, mon have I ever tried
@claudeladow2334
Жыл бұрын
No
@knightrider3766
Жыл бұрын
@@claudeladow2334 thx, 👌
Very nice plane p51. Mustang
@PassionHobbyRC
3 жыл бұрын
Thanks my friend rc
@keithsmodelsandrcs6593
3 жыл бұрын
@@PassionHobbyRC awsome
Looks a very nice little plane. Do you think I can bind it to a Radiomaster TX16S?
@PassionHobbyRC
Жыл бұрын
you have to see the multiprotocol
@claudeladow2334
Жыл бұрын
No. No one has figured out. Must change reciever/gyro. Then use multi protocol.
Should I hot glue a bit on the rear stabilizer?
I lost my couple days ago. Was wery stroing sunlight , i cant follow direction.
@PassionHobbyRC
3 жыл бұрын
attenzione, vola sempre in sicurezza rispettando le regole del tuo paese e calcolando sempre il pericolo e il rischio di un probabile evento
Hey mate, great video! Wondering if you can help me - I have the Volantex P51 750mm and there is a problem with the gyro stabilization when in high speed or dive, the plane starts moving around up and down violently trying to correct itself. Do you know an easy fix for this problem?
@PassionHobbyRC
Жыл бұрын
try to do the calibration before each video with the model at ground level
@toddventura7191
Жыл бұрын
@@PassionHobbyRC I tried the calibration but it doesn't fix this vibrating/wobbling around issue. With the stabilizer off (expert mode) it's perfect though. Any other ideas? Your airplane looks so smooth with the gyro on!
@robertheim352
Жыл бұрын
I've added some E-6000 adhesive on the corners of the servo/radio board to improve its mechanical connection to the main wing. The elevator tail wagging is gone.
@roadstar499
10 ай бұрын
@@robertheim352seems like a smart thing to do...if a gyro is not mounted correctly and glued or bolted to airframe and moves around,of course plane would be gittery...😊
@robertheim352
10 ай бұрын
My testing after adding glue to the receiver mount didn't solve the problem, although it did seem better. I also replaced the control linkage for the elevator since most of my tail wagging was pitch during aggressive dives and the control rod was long and thin (it flexes a bit). I added a stiffer control rod (not easy to do), but that didn't help much if at all. I also tried shimming the wing mounts to stiffen the overall fuselage to wing connection, but that didn't help. I expect the stabilizer code that runs off the gyro has too much gain. I'm still a novice and need the gyro engaged most of the time to avoid crashes.@@roadstar499
Cuando activo el giroscopio el avión se vuelve loco que puede ser?
@PassionHobbyRC
2 жыл бұрын
intente calibrar el aire en una superficie plana
Hello I have a question. I want to buy this plane first to start. I have never flown an rc plane. Please tell me if it is good for learning at the beginning or choose something smaller and cheaper at the beginning. I would like to ask for an honest answer and opinions about this plane. I will be very grateful. Greetings :)
@PassionHobbyRC
2 жыл бұрын
this plane is excellent and has assisted flight which makes flying easier for starters. I advise you to take extra batteries because the flight is about 5 minutes per battery. Hello
@claudeladow2334
Жыл бұрын
No not for 1st plane, trust me.
Minus all the cuts, how long did this take to build
@PassionHobbyRC
3 жыл бұрын
the first time it takes you more time. after much less. a good day
@landon_hartwig25
3 жыл бұрын
Thanks!
nice plane bro 👍👍👍👍....I'll probably pull mine out of the basement
@PassionHobbyRC
3 жыл бұрын
Thanks my friend rc 🤗🤗🤗🤗
my rudder is pulling left even tho im not even touching the transmitter, only in beginner mode.
@PassionHobbyRC
2 жыл бұрын
try to adjust the servo with expert mode and then come back as a beginner put it on the ground and do the calibration (vei manual) if the plane flies well as a beginner, don't do ninte. in expert mode everything changes because you have to manually trim from the remote control and adjust the flight of the plane. in the main mode, the control unit does everything so that the aircraft always straightens.
@korvslukarn3860
2 жыл бұрын
@@PassionHobbyRC Thank you very much, definitely deserved a sub :)
@claudeladow2334
Жыл бұрын
All seem to have problem w rudder in every mode but expert. Had to taxi straight into take off. Once in air not a problem.
Ciao ho acquistato questo aereo.. Ho appena finito di montarlo ma ho notato che le istituzioni fanno un pò pena.. Nn ho capito bene a cosa serve lo switch in alto a sinistra del telecomando e invece per lo switch destro ho capito bene la modalità expert é tutto in basso?? Le sarei molto grato per un aiuto. Grazie mille, le auguro una buona giornata
@PassionHobbyRC
2 жыл бұрын
ciao , ti accorgi se il modello è in modalità assistita se quando lo nuovi si muovano pure i servi degli alettoni che cercano di rimettere il modello in volo orizzontale . se i servi non si muovono vuol dire che il modello e impostato in volo libero è che non ha nessuno aiuto . Si ricorda di fare sempre la calibrazione prima di ogni volo con il modello a terra in piano . E tenere d'occhi il tempo di volo (che dipende dalla batteria che hai ) quella che ho io non dura piu di 4/5 minuti
@f14maverik
2 жыл бұрын
@@PassionHobbyRC ciao, grazie mille per l'aiuto.. Alla fine l'ho montato grazie al tuo video.. Appena riesco farò una prova di volo e speriamo bene 😁 vengo dal pilotaggio di un Xk a1200 aereo aliante più "semplice" 😁 Consigli un altro tipo di batteria o va bene quella originale? Grazie e buona giornata 🙋♂️
@PassionHobbyRC
2 жыл бұрын
@@f14maverik adesso no so che batterie mettono , quella che ho io durava scarso 5 minuti . questo aereo ha un volo più dolce e lineare 😀
Recieved mine a week ago have never flown before but i love this mustang cant wait to learn hope i dont destroy it 🙏
@PassionHobbyRC
3 жыл бұрын
good choice. important that you do the calibration and land on the grass if you can at least the first few times. take a 3-minute flight. Hello, my friend.
@richardrimel2306
3 жыл бұрын
Thanks for your video it will be helpful during assembly would appreciate and advice
@PassionHobbyRC
3 жыл бұрын
@@richardrimel2306 test the controls before the flight, do not fly in strong winds, make sure you fly safely and in the first few flights do not go too far away, you do not see the plane well. use the stabilized method to gain confidence with the plane.
@richardrimel2306
3 жыл бұрын
Is there by chance a link to buy extra batteries
@PassionHobbyRC
3 жыл бұрын
@@richardrimel2306 hello the link can be found in the description below the video. link accessories
Very nice plane, is it like 1/18 scale?
@PassionHobbyRC
3 жыл бұрын
the real one has a wing coverage of about 11.29 meters
Hello What lipo in ? 2s ou 3s? How Many mah ? Merci
@PassionHobbyRC
3 жыл бұрын
the supplied batteries are 2S 500mAh 7.4V / 20C) LIpo
@davidperin6925
3 жыл бұрын
@@PassionHobbyRC super 👍 merci beaucoup ! I think it will be my first plane 😉
Hello! How long it can fly?How far from you it can fly???
@PassionHobbyRC
3 жыл бұрын
dear friend, I have found a flight time of scarce 5 minutes under normal conditions. but if you push it the flight time decreases. I know you at least bring 3 bratteries
Like 84👍 Nice sharing Stay safe 🙏
@PassionHobbyRC
3 жыл бұрын
Thanks
What is the battery dimension recommended for this plane?
@PassionHobbyRC
2 жыл бұрын
Battery: 11.1V 500mAh e/o 800mAh 20C Li-Po e/o 2S 500mAhSize: (about)12*32*58mm e/o 3S 800mAhSize:20*25*70MM
@peterkennethnuevo6507
2 жыл бұрын
@@PassionHobbyRC Would a 3s 800 mah 11.1V with Pack Weight: 80g Pack Size: 57 x 30 x 25mm fit in that? Thanks!
@PassionHobbyRC
2 жыл бұрын
@@peterkennethnuevo6507 👌
@peterkennethnuevo6507
2 жыл бұрын
Thanks! I'm still a beginner, this channel helped me get into the hobby
Can a beginner use that?
@PassionHobbyRC
3 жыл бұрын
yes because it has the beginner function which makes the aircraft stabilized and avoids roll. always bringing it to the optimal position
Nice. Problem Solved.
@PassionHobbyRC
3 жыл бұрын
👌
can i install 3S?
@PassionHobbyRC
3 жыл бұрын
Yes . 3 s battery info in description below the video
it says 3s but the batt is 2s 500mah, did you try 3s?
@PassionHobbyRC
3 жыл бұрын
you're right friend. the batteries that come out when bought are 2S 20C. at 3 s never used it. thanks for your message
@claudeladow2334
3 жыл бұрын
Some are using zop 2s 850 mah from banggood.
@claudeladow2334
Жыл бұрын
Replace esc w 20a from bang good, then 3s.
i have the smaller one, nice plane
@PassionHobbyRC
3 жыл бұрын
yes I understand, they fly well
@rcflugkanalmeier
3 жыл бұрын
@@PassionHobbyRC oh yes
How much did that cost
こんにちは 私は日本人です 最近同じものを2つ手に入れましたが ジャイロの調子が悪くて EXPERTmodeでしか飛ばせません 初心者には苦労するので 困ってます
@PassionHobbyRC
2 жыл бұрын
こんにちは、各フライトの前にキャリブレーションを試みてください。モデルを地面に置きます
what is the flight speed?
@PassionHobbyRC
3 жыл бұрын
I can't tell you, its speed is adequate for its size. in favor of the wind goes that a beauty
@user-js5mg6ky1g
3 жыл бұрын
@@PassionHobbyRC thank you!
Mine eats batteries, I have a 500mAh 2s and I reckon I get about 3 maybe 4mins TOPS...!!!
@PassionHobbyRC
3 жыл бұрын
you friend the flight time is about 4 minutes. if you fly without wind and it lasts longer. if you fly with strong wind it can be 3 minutes I took 3 batteries
@adamrogers3221
2 жыл бұрын
@@PassionHobbyRC are there any battery upgrades you can get that make the flight time longer you think?
@PassionHobbyRC
2 жыл бұрын
@@adamrogers3221 Battery: 11.1V 500mAh ~ 800mAh 20C Li-Po info in description
@claudeladow2334
Жыл бұрын
Replace w 850mah 2s.
🥰🥰🥰😍😍😍💪💪👏👏👏
@PassionHobbyRC
3 жыл бұрын
Thanks 🤗🤗🤗🤗🤗👍🏻👍🏻👍🏾👍🏾
무스탕.?
I think something is wrong with my reciever. The channel for tge rudder is all Jerky and sticks random . Servo is ok in different channel
@PassionHobbyRC
Жыл бұрын
try to calibrate with the model on the ground on a flat surface
@creepinonthebabes
Жыл бұрын
@@PassionHobbyRC already tried everything. Reciever is bad in safe mode
@claudeladow2334
Жыл бұрын
Reciever / gyro bad. yup
Nice plane, however the first flight was terrible, it wobbles a lot and I don't know why
@PassionHobbyRC
3 жыл бұрын
hello, what do you mean wobble? flown with strong wind and gusts?
@giacomozambelli421
3 жыл бұрын
@@PassionHobbyRC c'era un po' di vento, ma niente di che. Sostanzialmente oscillava parecchio con il gyroscopio attivato, come se stesse cercando di correggere il vento ma entrava in "risonanza" oscillando sempre di più.
@giacomozambelli421
3 жыл бұрын
@@PassionHobbyRC in più ho il problema del rudder che non ritorna nella posizione centrale con il gyroscopio attivato. Anche il tuo ha lo stesso problema?
@PassionHobbyRC
3 жыл бұрын
@@giacomozambelli421 Capisco perfettamente quello che dici. io con il mio modello non ho avuto questi problemi, il modello volava abbastanza lineare è il timone non mi dava problemi. (tieni presente che in volo stabilizzato i movimenti di timone, elevator e alettoni si attenuano) Volare con un aere stabilizzato è completamente diverso dal volo libero perché la centralina combatte sempre per allineare il modello è i comandi si danno in maniera diversa dal volto non stabilizzato. Hai provare a calibrarlo prima del volo ...mettendo il modello a terra abbassando i comandi del radiocomando minuto 13:27 trovi le info sul manuale e/o in questo video. Ci aggiorniamo a presto
@giacomozambelli421
3 жыл бұрын
@@PassionHobbyRC grazie mille del tuo aiuto. Sì ho fatto più volte la calibrazione, ma sembra non registrare correttamente la posizione orizzontale e mantiene salvata "quella di default" e si vede dal fatto che l'elevator rimane sempre leggermente scostato. Un altro problema che ho notato è che il raggio di azione di elevator e rudder è molto maggiore in beginner rispetto alla modalità manuale. Cosa che dovrebbe essere proprio il contrario. Potrebbe essere il gyro difettoso anche se spero fortemente di no