@Mustafa Kyler Do you respond to your other sock accounts often?
@JamesGrates5 ай бұрын
Great vid bud just joined your channel we speed run only but I’ve been using your set up tips in are effort to go straight and fast H and w racing channel
@teabagmcpick58197 жыл бұрын
Thanks Edward. That was a good, clear explanation of something I always found quite confusing & had difficulty remembering the right way to go. The side with the higher gauge value needs to have the linkage lengthened & the equal+opposite adjustment on the other side.
@hollywoodfresh11205 жыл бұрын
Yes you are right long video but profession takes time job well done explaining and showing keep up the great work👌😎👍
@alberfpv Жыл бұрын
I normally use this method but with more weight (arms and transmission connected). With less weight the other side are going to go up more reactive so yo get less precision.
@MetalMathiasTP
11 ай бұрын
I agree with your method, this is also better. More weight on arms and fully assembled car is better to do adjustment with. The weight difference in each side and friction differences also need to be take into account.
@kevmoxley2926 жыл бұрын
Great video. Just looking at the video and how you were adjusting the bar, doing the opposite to the other sway kept putting you in the same position from when u started. By just lowering or raising one side would have gotten you the results you were looking for on first try. “Measure twice, cut once.”
@bobbymalta735 жыл бұрын
Thanks!
@MrUCL6 жыл бұрын
Edward, Why are you not making videos any more? Do you run vbc d10? Make a video on that build. Thanks I enjoy your work.
@oksklsk7 жыл бұрын
It is what I want to know. Thanks a lot. :)
@EdwardPickering
7 жыл бұрын
Glad this video helped you out.
@TheGetintoit6 жыл бұрын
The grud screw at the front of the inside rear suspension arm obsolete with anti-roll bar.
@theeviloneohyes5 жыл бұрын
have you seen the anti roll bar set up on the new race opt mts t3
@royarsey54295 жыл бұрын
toys have come a long way...who would imagine people can get hooked on RC
@NODTHEROD7 жыл бұрын
Thanks for making this video
@EdwardPickering
7 жыл бұрын
You're quite welcome! Please enjoy all the other videos I have and will make.
@ayske17 жыл бұрын
Can the anti roll bar wire be warped over time that makes it hard to balance both sides
@EdwardPickering
7 жыл бұрын
Yes, it can. Even straight out of the package. You should always test and make sure the roll bar is tweak free. You can do this by placing the roll bar on a flat piece of glass.
@sgtlt7 жыл бұрын
where did you get the plexiglass plate, does it matter how high or low the ends of the anti roll bar are set at? thanks great informative video like allways.
@EdwardPickering
7 жыл бұрын
The plexiglass is a chassis tweak plate by a company called TN Racing. The roll bar ends will be slightly different in length. The most important thing is to make sure the roll bar is tweak free.
@sgtlt
7 жыл бұрын
Thanks for the reply. I use all your set up advice, thanks for the help
@skelejp99825 жыл бұрын
How about a Drafting Compass, make 2 holes in table , attach some weight on cable both side.
@Americanblood765 жыл бұрын
I know I’m off topic but why is it that almost every KZreadr is Canadian?
@devinsilva47236 жыл бұрын
By threading up and threading down you mean to tighten and loosen correct?
@EdwardPickering
6 жыл бұрын
Threading up means to lower the height of the arm. Threading down means to raise up the height of the arm.
@leoncowley868 Жыл бұрын
Let's see it happen like this when the car is built ☝🏼👇🏼 Turnbuckles are a thing 🤔
@MetalMathiasTP11 ай бұрын
This method IS precise... Until you put all upper arms and other parts on the car. Then the weight difference and difference in friction on parts on left to right for each arm will again be different and you need to adjust it again. I bet it will be off when the car is fully assembled without tires and you retake the measurement.
Пікірлер: 28
I watched this and I don't even have an RC car.
@thybigballs
3 жыл бұрын
@Mustafa Kyler Do you respond to your other sock accounts often?
Great vid bud just joined your channel we speed run only but I’ve been using your set up tips in are effort to go straight and fast H and w racing channel
Thanks Edward. That was a good, clear explanation of something I always found quite confusing & had difficulty remembering the right way to go. The side with the higher gauge value needs to have the linkage lengthened & the equal+opposite adjustment on the other side.
Yes you are right long video but profession takes time job well done explaining and showing keep up the great work👌😎👍
I normally use this method but with more weight (arms and transmission connected). With less weight the other side are going to go up more reactive so yo get less precision.
@MetalMathiasTP
11 ай бұрын
I agree with your method, this is also better. More weight on arms and fully assembled car is better to do adjustment with. The weight difference in each side and friction differences also need to be take into account.
Great video. Just looking at the video and how you were adjusting the bar, doing the opposite to the other sway kept putting you in the same position from when u started. By just lowering or raising one side would have gotten you the results you were looking for on first try. “Measure twice, cut once.”
Thanks!
Edward, Why are you not making videos any more? Do you run vbc d10? Make a video on that build. Thanks I enjoy your work.
It is what I want to know. Thanks a lot. :)
@EdwardPickering
7 жыл бұрын
Glad this video helped you out.
The grud screw at the front of the inside rear suspension arm obsolete with anti-roll bar.
have you seen the anti roll bar set up on the new race opt mts t3
toys have come a long way...who would imagine people can get hooked on RC
Thanks for making this video
@EdwardPickering
7 жыл бұрын
You're quite welcome! Please enjoy all the other videos I have and will make.
Can the anti roll bar wire be warped over time that makes it hard to balance both sides
@EdwardPickering
7 жыл бұрын
Yes, it can. Even straight out of the package. You should always test and make sure the roll bar is tweak free. You can do this by placing the roll bar on a flat piece of glass.
where did you get the plexiglass plate, does it matter how high or low the ends of the anti roll bar are set at? thanks great informative video like allways.
@EdwardPickering
7 жыл бұрын
The plexiglass is a chassis tweak plate by a company called TN Racing. The roll bar ends will be slightly different in length. The most important thing is to make sure the roll bar is tweak free.
@sgtlt
7 жыл бұрын
Thanks for the reply. I use all your set up advice, thanks for the help
How about a Drafting Compass, make 2 holes in table , attach some weight on cable both side.
I know I’m off topic but why is it that almost every KZreadr is Canadian?
By threading up and threading down you mean to tighten and loosen correct?
@EdwardPickering
6 жыл бұрын
Threading up means to lower the height of the arm. Threading down means to raise up the height of the arm.
Let's see it happen like this when the car is built ☝🏼👇🏼 Turnbuckles are a thing 🤔
This method IS precise... Until you put all upper arms and other parts on the car. Then the weight difference and difference in friction on parts on left to right for each arm will again be different and you need to adjust it again. I bet it will be off when the car is fully assembled without tires and you retake the measurement.