Amazing video! I never thought of putting two flybacks in series before...

Impressive all the way around especially that you built your own ZVS driver. Very clean 👌

Hi, good job, I've done this too, I just wired the inputs of the flybacks in parallel and then the outputs in series, it was easier that way for me and I dont like batteries... My luck was that I've found a transformer which has 24V and around 20A...since my multi meter cant measure more I dont know for sure xD but mine doesn't needs a little bit of time to grow the sparks it just needs a min of 6-7cm to make a spark it works so awesome !!! You were the one who inspired me to male thos, who showed me how awesome the electricity is !!! Thank you, I soon will make a Tesla coil with it!!! Thank you again and have a good day!

@cisarvialpando7412

4 жыл бұрын

Yes Ludic Science is the one from whom I learnt many things about flybacks and High Voltage... I first made a slayer exciter tesla coil by watching the video of Ludic Science....💯💯💯💯💯💯

I am going to try this with 4 flybacks AWESOME!!!

@gregandark8571

8 жыл бұрын

+ivan R DONT LOOSE YOUR HEAD !!!

@ivanrodionov9724

8 жыл бұрын

dont worry :D I just finished it :) IT WAS FUCKING AWESOME!!!!!!! (until one flyback released the magic smoke).

@gregandark8571

8 жыл бұрын

ivan R lol

@pierreuntel1970

8 жыл бұрын

+Ivan R I doubt it, flyback are not easy to release smoke since it's all glued

@ivanrodionov9724

8 жыл бұрын

SandPox trust mre, 400kv is enough to release the magic smoke from anything!

One of my favorite Ludic episodes. 👍

Thats a big arc, good job!

Very nide video! Keep up the good work!

I built it. It works well, got over 42 kV on the output (measured with a high voltage probe). But while I was so excited about it (and cranking up the power supply!) one of the flybacks failed. So this setup produces high voltage, but 1) only for short time 2) not in short circuit or no-load mode (leads to internal breakdown quickly). So be careful!

@dogodogo5891

5 жыл бұрын

how many flyback your setup? maybe you can dip it into pure mineral oil for avoid fail

@mareksvrcina5279

4 жыл бұрын

How did you measure the voltage? I have built a voltage divider which is basically the same a HV probe and found the frequncy to be too high to be measured with a simple multimeter.

@whimsy5623

2 жыл бұрын

Dear Lord do you still have all your limbs?

@harms123

Жыл бұрын

@@mareksvrcina5279 If that's true then an ossiloscope should do you fine

Wow! Did not know you could connect them like that. Good job.

@ludicscience

Жыл бұрын

Thanks!

+Ludic Science Awesome video as always !!! i want to see both transformers power a tesla coil !

1. when you wind wires on FB core first wind it then put the iron holder over the wires. 2 you can wind coils with center taps directly on the flyback cores and connect them completely in series (best 3+3 for high voltage) or you can wind half coil on one core and the other half on the other, just make sure you use thick wires and connect the capacitor as near as possible to the coil if you do so. 3 get a straw, do a hole in it, put the wire and now you have chicken stick. great video and you can make part 2 with some audio signal on a second wire on the input inductor

Thanks Ludic!! :)

@ludicscience

8 жыл бұрын

+Brugga Jugga :D

thanks for sharing Ludic Science

What would happened if You wound opposite direction coils on ferite core instead of same ?

can you make another adjustable boost converter apart from the previous one?

I think you would pull a longer arc if you moved the wire upward as the spark is intending to go. The ionized air is conductive and warm, so it wants to rise--follow this path. This is precisely why the arc of a Jaccobs's ladder goes up. A Jaccob's ladder will not work if placed on it's side or upside down, as this is not the natural direction of the heated ions.

Do you have the schematics for your "Tesla Coil"? Thanks for your video!

Please provide the circuit diagram

great job sir....

Interesting how these arcs follow some wave patterns, especially 24v-one. Like here: 3:02 the arcs bother to make circular form.

@wiebmeister

3 жыл бұрын

I'm pretty sure that's because the plasma is hot and thus rises upward

very good job 👍

Though this has very high current; shown by the plasma; the voltage is quite low: Maybe 10kv max judging by the initial spark gap ignition.

Also I would love a video on going over how your determinted your turns for the tranformer

@Heheboigod2

Ай бұрын

Touch the lower end of the transformer to the upper end of the other transformer. And arcs 🤩

nice soft switching

How to make it

Awesome!

You can achieve the same results by eliminating the first ferrite transformer and wrapping the yellow coil around both flyback cores arranged back to back. So you will essentially have one primary wrapped around two cores.

Thumbs up :) Alex

thanks a lot 😀 sir

Very nice and awesome,, .. if want to change Frequency, how to do that?

Parabens pelos videos tenho apreendido muito.

@ludicscience

Жыл бұрын

Obrigado

wooow high voltage !

Can we use two electronic balst instad of the iron core and zvz driver and connected in serie of two flyback transformer

Put 8 to 10 turns primery coil on each transormer and connect them in parallel directly to output of the driver, you wil have higher voltage.

@diecksl

5 жыл бұрын

Connecting the primaries parallel sounds like a good idea to disable the additional ferrite core from the video. However, I think the connection should be antiparallel (switch ZVS leads on one transfomer to get antiparallel phase)? What do you think?

Everything is better in series including flybacks!

Nice and interesting project but very very dangerous:)

@GGI159

4 жыл бұрын

You know it's high frequency and touching it only burns you right?

The current seems quite high, I guess it could shock you unless the current is low like plasma globe, am I right?

You should build a bad ass Jacobs ladder with this setup.

what is the amparge on the flyback transformer?

What's special about that Mazzili driver? can you link to you link to an original circuit or your circuit diagram? thanks

How did you extract that center core from an old flyback? And could i use two flybacks in parallel to increase its current or make the flyback last longer due to shared load = less heat? I know you could increase current by adding capacitors since adding capacity would decrease the voltage thus increasing the current... but that bit is too tricky to find a good balance.

@Chuckiele

6 жыл бұрын

Yes, secondary in series doubles the voltage, secondary in parallel doubles the current.

How would you add frequency generator to this circuit

If i connect the fbt in parralel, can i get bigger amp@current ?

Is it possible to replace a core of a flyback thing with a chassis mount transformer 60Hz. It should do the same thing right? I don't have flybacks and I am trying to build a mosfet driver for an ignition coil setup.

What is the power draw on your driver?

Hello sir, can i get the estimated current draw from this amazing device?

how can I made this flyback .. can you please help me !

If you bypass the diodes in the flybacks or wind your own flyback secondary cores, can this circuit drive them to produce AC instead of DC? Perhaps by winding each half of primary in different directions?

@Chuckiele

6 жыл бұрын

Most flybacks you will find are filled with solid resin and its impossible to get rid of the diodes, making them useless for many applications, as it usually outputs pulsed DC. This one however outputs smooth DC as you can see from the arc being able to grow bigger when pulling the wires apart after it jumped, which can be useful for a Jacobs ladder for example. Winding the secondary yourself is pretty much impossible aswell because it needs a huge amount of turns in a small area perfectly isolated, but you can find some rare flybacks that either have the diodes outside of the case, or no diodes at all, which makes them perfect for many AC projects.

Why do people always make the high voltage driver circuit using a center tap transformers but not with normal 2 pins, transformer? I'm still in having trouble building the oscilator circuit for the transformer to step up the voltage.

Wooooow!!! That could be a good trap ;p

How much amps do you need for zvs fiyback transformer driver

WOW!

nice arc

@achachm

5 жыл бұрын

Thanks

with a ZVS circuit one can do even more nasty arcs, with a single flyback and only 24V and 10A at the input. I dont know why, but these seem to be more efficient. Maybe its the frequency or something.

@ludicscience

Жыл бұрын

yes zvs is a beast!

And if you want the arc to sound scary, you can add a 555 timer on the input set to oscillate at 50Hz!

@revolution5547

3 жыл бұрын

These transfirmers will not work at 50hz

@treasuretotrash2067

3 жыл бұрын

@@revolution5547 Modulate it at 50hz, not run it at 50hz

@revolution5547

3 жыл бұрын

@@treasuretotrash2067 oh

Nice!

are posible use that for CO2 laser power supply.?

Ludic how much input is

please be descriptive more, thanks

can it be. used to power ion thruster

@HobkinBoi

5 жыл бұрын

@@thomasmaloney6537 Most flyback transformers have a rectifier diode which ensures the output is DC. So, you probably could use it.

Can use swtching power supply for cctv sùch as 12v/30a. Thanks

@ludicscience

Жыл бұрын

Yes you can

This video is absolutely awesome! I Never considered the possibility of two flybacks in series. Does the higher voltage give a risk of them arcing through the core, thus reducing the life of your flyback? (also, when describing the coils, in English we say "wound", not "wounded" Example, "There are five turns *wound* around the core")

actually sir I am not getting that of what value of capacitor and diodes we have to use and the input supply also 😞😞😞😞

hi... i tried to make the zvs driver for flyback but... it didnt work on my flyback. the flyback is new one and it work with joule thief driver. is there any type of flyback that doesnt work with zvs driver?

@Heheboigod2

Ай бұрын

The transformer is probably broken

Can you tell the model of yhe flyback transformer ?

Could this be used for a Jacobs ladder?

@Chuckiele

6 жыл бұрын

Yes, absolutely. The distance at which the arc begins isnt to small and the distance to which it can be pulled is very big, very good conditions for a huge Jacobs ladder.

reckon those gloves are appropriate? Looks like cotton

Thought I'd note a correction for you. You said the flybacks are rated at 12kv, when you connect them in series on the output and in parallel on the input, the voltage of the two is added together, not multiplied. Your resulting out voltage is more around 24kv, not 400kv. Also the distance at witch your ark begins seams to support the 24kv range. Look up how to built transformers and when you get deep enough you'll see whats happening when you do unusual configurations with them. You discovered one: 2 transformers paralell input, series output, twice the voltage output, twice the current input, same voltage input. Hope I was helpful. Have fun!

@tobinator680

7 жыл бұрын

He said 20kV not 12kV and 40kV and not 400kV

@coilsmoke2286

7 жыл бұрын

He is getting at least 40,000 Volts judging by the length of that arc...

@Chuckiele

6 жыл бұрын

judging by the lengh of that arc and the lack of audible noise, the flybacks output smooth DC and deliver high current. When looking for the voltage, the distance at which the arc begins is important.

Any chance you can post the schematic with part numbers for the mazzali driver? Flyback model numbers would be good too.

@ludicscience

8 жыл бұрын

+Ethan M check my previous video: kzread.info/dash/bejne/g3V7o62gotq0e84.html

@ethanmye-rs

8 жыл бұрын

+Ludic Science Thanks, didn't see that! Any idea on output current capability?

@ethanmye-rs

8 жыл бұрын

+Ludic Science also, with 40kV, have you considered xrays? Maybe an old tube w/o leaded glass might be a good way to get a few

@ludicscience

8 жыл бұрын

+Ethan M Thst's a good idea, maybe I will try. Current must be around 3 mA

Is there any ozone production by this method

@Pullsee

Жыл бұрын

Yes, ozone and nitrogen oxides

You should adding more capacitor for the primary coil. Over 150 KHz is bad.

Just imagine electroboom trying to make something like this

@Mark-tv4df

3 жыл бұрын

Kaboom

Can you give me circuit diagram..?

Can negative and negative connect together to get 2 positive terminal? Tq

@ludicscience

Жыл бұрын

No

do you have a schematic if this?

@electrobus5095

8 жыл бұрын

Google mazilli driver or buy one on ebay ... zvs driver

at what point is that likely to destroy those flybacks?

@cisarvialpando7412

4 жыл бұрын

Good question. I also have this doubt.

I will learn all this in Electrical Engineering right?

@ludicscience

8 жыл бұрын

+Carlotv right

@carlotv1212

8 жыл бұрын

+Ludic Science I wish I knew everything already

that is 1cm so not more then 10kv. its the breakedown distance of non ionized air that counts not how long one can draw the arc.

Mightn't it be even better to wire connect the primaries of the flybacks so that the flybacks are 180 degrees out of phase? Then you could connect the two bottom pins together for the series connection, and obtain your high tension from the two high tension wires of the flybacks. This would be more elegant, and possibly avoid potential HV arcs occuring where you don't want them.

Amigo seria possivel colocar 3 ou 4 flaybacks em serie ? Talvez com outro circuito ou quem sabe em paralelo?

@ludicscience

Жыл бұрын

He visto que coloquen 3

what kind of mosfets? and could you leave the video about the mazzillie driver in your next comment? thanks STAY SAFE :)

@ludicscience

8 жыл бұрын

+Lost In Space Electronics IRFP250 kzread.info/dash/bejne/g3V7o62gotq0e84.html

@lostinspaceelectronics870

8 жыл бұрын

+Ludic Science love you buddy : )

Could this somehow work with a ZVS driver?

@AdamAvacado

4 жыл бұрын

This is a zvs driver lmao

@revolution5547

3 жыл бұрын

That was a zvs driver

How many cost please reply

Can you please give me the circuit please

Then looks like you would only get shocked one time!

The frequency is to slow. You need a 555 driver for higher frequency and get bigger arch

@uK8cvPAq

5 жыл бұрын

Actually it looks like the frequency is changing as he draws the arc out.

Where can i buy this flyback transformers for cheap ? please send me a link ... Thanks for your video Leon

@minecrafter9099

8 жыл бұрын

+HV and more in old tvs, the tube ones

@electrobus5095

8 жыл бұрын

Yes but i live i germany and dont have one (looking on the street is illegal) so i have to buy one but which one is suitable with a high voltage but low amperage...?

@LGbaSS-bi2ml

8 жыл бұрын

+HV and more m.ebay.com/itm/Flyback-Transformer-NTE-NTEFT138-/331829253839?nav=SEARCH this one should be fine.

@electrobus5095

8 жыл бұрын

+InTeg3R-9¹³5 NoPreferences Thank you ;)

The problem here that your arc starts from 2 cm distance it generates 20kV.

Jerry lucid I made a clean sounding audio modulated zvs driver actually it's combined 555+zvs now you can play music with a flyback transformer do ypu want schematics

@ludicscience

7 жыл бұрын

That looks great! did you made a video?

@mrinalthakur3459

7 жыл бұрын

Ludic Science no sir

@mrinalthakur3459

7 жыл бұрын

Ludic Science belive me its one of the cleanest sounding plasma speaker ever

@mrinalthakur3459

7 жыл бұрын

Ludic Science you can make a video about it

@mrinalthakur3459

7 жыл бұрын

Ludic Science i saw you have all the past necessary for making it

sir,my flybacks are burning how ca I fix that problem

@uK8cvPAq

4 жыл бұрын

Clean it up, remove the charred bits and put it in transformer oil then hope for the best.

What , you are using cloth gloves as HV protection !!

Hi I will make it with driver

DC Voltage can be very dangerous .. Use with cation Bud!!

@motherjoon

8 жыл бұрын

+violeman Its AC

@violeman

8 жыл бұрын

motherjoon K so you just transformed the voltage then !!! Right on!!! I was Just saying that DC is Dangerous!!! Thanks 4 Sharing Bud.

@lostinspaceelectronics870

8 жыл бұрын

+motherjoon sir the flybavks he is using have hv diodes in them so you wanna tell me how it's ac

Eeee. Actually I want to know that how can I check that wether the hv diode inside a flyback is damaged or not....actually I have a zvs driver....and I am afraid I ruined my flybacks internal diodes after I peaked 600watts😀.

Would you help me

show me the circuit diagram please

@ludicscience

8 жыл бұрын

+amit singh mazzilli driver is here kzread.info/dash/bejne/g3V7o62gotq0e84.html

奇實要使电成直缐，可用珫璃皿管型，皿管头易導电功能，集电而皿管出。 若无伺服机可控晶体，自研防備，以防末来机器人假失控而自卫。 但勿伤人用。

@shaneclark5022

6 жыл бұрын

hahah soooo true

Why couldn't you just connect flybacks in parallel

@Pullsee

Жыл бұрын

The secondary windings of the flybacks must be wound in opposite directions.

Ludic science, how much KV it ?

@sammizan4522

8 жыл бұрын

+Ludic Science, how much KV it ?

@sammizan4522

8 жыл бұрын

i need information about KV that your experiment 12 volts and 36 volts.. Reply please Ludic Science. Thanks you.

@ludicscience

8 жыл бұрын

+Harukichi Yakuza at 12 you get around 15 kv and at 36 v you get around 40 kv, depends on the flyback model

@sammizan4522

8 жыл бұрын

+Ludic Science ok, thank you brother. Nice information

Can it kill someone ??