Turn OFF SLIP, VDC, ABS, Nissan Infiniti g35 350z mariano, Pathfinder, cube, quest, altima, maxi
Автокөліктер мен көлік құралдары
G35 playlist here • G35 / 350Z Infiniti/Ni...
Support my Channel here! / dannyjohnson
Here is a list of parts that can trip it. Try to run the codes for the check engine light if possible. Disclaimer, I am an amazon affiliate and may receive a commission for providing the link, but the price is the same for you.
Cam position sensor amzn.to/3pBZUBg
Mass airflow sensor
amzn.to/3vIZtce
Throttle position sensor
amzn.to/3MhCH17
CLEAN ABS SENSORS Front • How to locate and remo...
CLEAN ABS SENSORS Rear • 99-04 Cobra ABS sensor...
Disclaimer: I am an amazon affiliate, so when you purchase through the links I provide it supports the channel with a small referral commission. The price is the same for you
Пікірлер: 573
I have a 2010 Infinity QX56. I tried these steps today and it actually worked. All of my lights went out. Thanks for sharing.
Hey Danny, 1st of all thanks for sharing this video. I have a 2006 Murano which died in the middle of the highway on my wife the other day. I couldn't figure it out it went into limp mode driving about 5-7 mph. She cruised it to the shoulder and we had it towed home. Fast forward to today after testing it out again it was still going into limp mode. I'm watching a number of vids related. Your video saved me a lot of work. My brake and ABS lights were flashing. I checked my fluids and the psf was low. I added atf to the reservoir and all the lights when of and it started driving normally again. Thanks a million man
@dannyjohnsonsgarage
5 жыл бұрын
So glad you found the video! Thanks for watching
@tonylopez2106
5 жыл бұрын
Having the same problem in my infinity g35 you added power steering and what else?
Thanks bro was looking for this everywhere for a easy quick basic fix or an idea on what to do you were the only video!!!! thank you keep up the great work
Had to comment to say thank you. Coolant level was extremely low in my car, never realized it. Filled it up, cleared the "camshaft" code, running great ever since.
@dannyjohnsonsgarage
4 жыл бұрын
it’s nice when it’s just something simple! My father in law took our car in without me knowing since the lights came on and the dealership wanted $75 to add some power steering fluid! I told them no, added some and was on my way.
I am the original owner of a 2004 armada, I would usually get the ABS effect when I had done a jump start to another vehicle, but lately I have been getting a brake light indicator on the dash then VDC and slip lights would turn on and then later get the ABS effect. I checked all three fluids and they were within ranges. I decided to add brake fluid to the max line and this has stopped my issues. I too had watched other you tubers saying they replaced the brake booster or the ABS module with no benefit. Thanks for placing this video on yt
Love the way you explain what to do
Life saver! I got the slip, abs and vdc off lights on my 03 coupe after trying to skirt skirt. I added some coolant because i was basically empty and that did the trick! Thank you!!
@NSRTalonzo
3 жыл бұрын
How long did it take for the lights to disappear?
@aaronpruitt5814
3 жыл бұрын
Yes how til it disappeared?
@NSRTalonzo
3 жыл бұрын
@@aaronpruitt5814 Disconnect battery! Wait 5-10 minutes.
Thank you. That's great demo with clear explanation
Thanks Danny, it worked and my OCD can rest again.
@dannyjohnsonsgarage
4 жыл бұрын
Glad you found the video. I have more videos like this you may enjoy kzread.info/head/PLIjr-uSYDZi6cuomOpHL7rGWNEbQUmbvy
Thanks! My 2008 pathfinder stalled after making a left turn. I restarted and noticed VDC and Slip came on at the same time. Watched this video and then checked my fluids. My Power Steering was at min level so I added power steering fluid. I then disconnected battery for 10 minutes to reset computer and voila problem has gone away! Thanks again !!
@dannyjohnsonsgarage
3 жыл бұрын
Glad it helped! Many things can trigger it. Kind of annoying lol. But at least it makes us verify things are safe
@sprmwales27
3 жыл бұрын
I bet it was the crankshaft sensor or cam sensor lol i had to replace both of those with my pathfinder.
Thanks man ,that was really helpful
You’re a lifesaver!! It was the coolant. I’m back on the road 😎🙏🏾
@OleBoyyy15
3 жыл бұрын
I was actually low on all 3 😂 but how low was yours? I tried everything and I can’t get the lights to go off.
OMG JUST GOT A 05 & THOUGHT MOTOR WAS SLIPPING SOON😂😂😂😂THANKKKK YOUUUU!
@phenomenaljone
3 жыл бұрын
🤣🤣😂😂🤣😂🤣😂🤣🤣🤣😂😂😂🤣🤪 me tooo I’m like ooh lard not so soon the transmission or engine slipping 🤣🤣🤣🤣😂😂
@angelray8385
Жыл бұрын
@@phenomenaljone ++p 0po0
@angelray8385
Жыл бұрын
@@phenomenaljone ++p 0po0
@king_Charles501
Жыл бұрын
🤣🤣🤣🤣🤣
@jahelml4658
11 ай бұрын
@phenomenaljone
Thanks so much man this helped when I was out driving my family
U saved me literally i got to work and the abs started running the test and i turned off the car and that noise came on i did what u said and it worked
Thanks so much for your video! My 2006 Infiniti G35 just did that on me. I had to remove the battery cable to save power. I plan to take to the shop this weekend but it seems like I what did would reset the sensors. Again! Your video is a real life saver for me!
@dannyjohnsonsgarage
5 жыл бұрын
I’m glad to hear that it was useful. Good luck- as you see it can be a number of things
@red_day6097
4 жыл бұрын
Wait so let me understand this.. this isnt fixing your car its just patching it for a couple weeks? Does this method still work and how long do the VDC Lights and stuff stay on for? Would this also work buy using a diagnostic device and deleting the codes.
@DeuceVi2ion
3 жыл бұрын
It is just resetting the system later on driving it will pop up again. This does not fix, it’s a common problem with the Infiniti’s, it is a sensor issue that without it it takes off ur ABS VDC slip and another one I can’t remember.. change the sensor if u want ann bc permanent fix.. another one is the gally gasket in the engine behind the timing belt.. big job, but a common problem for g37s, the factory gasket was a defect n most engines will be leaking out from that gasket.. if u change all that it’s like a new car again.. hope this helps someone...
@xxxko4532
3 жыл бұрын
Hi everyone my Nissan Murano 2006 it's on ABS ,VDC,Also slip light on I need to turn off please
@jeanjacque1577
3 жыл бұрын
@@xxxko4532 abs relay
Thank you so much! It happend as soon as I got home from work while driving in the rain thanks for the explanation I was able to turn of the lights
I love this car and the battery disconnect advice is fantastic....
ThankSs, you make my day !..!
worked for me! thank you so much!
Thank you so much for all the information you shared with me.
Dear Danny Johnson, I had the exact problem shown in your above video. Fluid levels were all OK. I disconnected the battery negative and that did the trick! Very good outcome! I had to reset some electronics inside the car, like the radio, electric seats, etc... No big deal. Thanks a bunch. :)
@dannyjohnsonsgarage
5 жыл бұрын
Lowry Pierce Glad it helped out!
@luiselapostolfeliz2421
2 жыл бұрын
@@dannyjohnsonsgarage Hi Danng! My name is Luis Urbieta and I have a question. What dos VDC and ABS stand for? Love how you explained what you have to do and we have a Nissan Centra that does that. Please answer my comment when you can. Thanks.
@vortecturbo
Жыл бұрын
@@luiselapostolfeliz2421 vehicle dynamic control, anti-lock braking system
@luiselapostolfeliz2421
Жыл бұрын
@@vortecturbo OK thank you.
Thanks for your video . Just now that happens to my car . And I was serah for the meaning . Thanks you give my the reason.
Just bought a used one. Thanks for the heads up on the system testing itself. 👍🏼
Awesome video!!
@dannyjohnsonsgarage
5 жыл бұрын
Thanks! Glad you enjoyed it
Bruh... ive wondered what that pffff noise was for years 🤣🤣🤣.. thankyou!! Every morning at pulloff the car would go pffff and i just got used to it.
Thanks Danny
@dannyjohnsonsgarage
4 жыл бұрын
You’re welcome! Feel free to see my other videos on this car! kzread.info/head/PLIjr-uSYDZi6cuomOpHL7rGWNEbQUmbvy
I usually get rid of the lights and the buzzing by putting it into neutral while driving 10+ mph and shutting the car off and starting it again- yes while driving. It’s a little sketch but it works every time. My car just needs a new abs module.
Great video and explanation
Thanks ....Great suggestion
Thanks Danny that really helped. I have a 2008 Skyline with that problem. So thank you very much. And ironically my name is Daniel and they call me Danny too.👊🏽👍🏾
You very much good information
Also check your ABS sensor on your rear differential it can wiggle out and throw all three lights. Or you can just take the sensor out of its spot if you want the lights to come on
I'm 3 for 3 on this procedure. It works GREAT! Thanks for the video. I have a 2005 Infiniti G35 manual transmission sedan. This has happened 3 or 4 times in the last couple of months. In at least two cases, lights came on after hitting a speed bump. Today, I didn't even bother to disconnect the battery. I just started the engine, did a sharp left hand circle. Pump stopped but lights still on. Turned off the car. Started it, did the left turn again and lights cleared. Tested the VDC control button and it functions on/off again. Fluid levels look OK but I'm going to top them off to see if things improve.
@scottyscott1898
4 жыл бұрын
Arctic Minibike so, how did it work? Everything back to normal with topped off fluid levels?
@arcticminibike4033
4 жыл бұрын
@@scottyscott1898 I never got around to it yet, but things have been fine for the last 2 weeks. It's only a matter of time before it does it again. The majority of threads point to the relay as the issue. It's just an expensive gamble. For now I'll keep doing the occasional cheap reset until it gets too frequent. I need to do the control arm bushings, so I'll look for a loose sensor or wiring. Seems odd that every time it happens corresponds to hitting a speed bump.
@jeanjacque1577
3 жыл бұрын
@@arcticminibike4033 definitely the abs relay . I replaced mine today with 1 from the junkyard it was 10 bucks compared to 220 new
I've been dealing with this on my 2005 G35 Coupe 6mt under 70k miles. Having found a few videos and tips on G35 forums... I have seen people talk about 1. low fluid levels (no for me) 2. rusted or impaired sensor contaminates on the brakes (not sure), 3. Fix- High G maneuvers to trigger the ABS to reset. I've had success after 2-6 times going at idle at 5-10 mph (with no one behind me) and SLAMMING ON THE BRAKES and having it skid (no ABS) to a stop. Luckily, I live in a place with lots of empty streets and stop signs... (I've heard of people going to parking lots and doing a hard turn plus the stomping on the brakes) to get the high G's. I've also heard of guys going backwards and slamming on the brakes.). Some guys even take a pair of pliers and hit the ABS humming motor if not shut off will kill your battery and itself - if you can't stop it when you shut off the car and it keeps going. Back up solutions - pull the ABS circuit breaker next to the battery... and or disconnect the battery - that will then continue to screw itself when re-connected the next day itself unless you get it to reset. This is pissing me off now... as I need a car to work and not drive around like a drunk slamming on my brakes, screeching to a stop, turn off and on, and hope it resets... today was 6 times... slick parking garages don't work as well. You really need the hood to dive at taxing speed or 5-10mph... full stop for it to reset. Grrr... If this continues it is time for a dealer to screw me or an semi-competent Shell dealer as there are multiple possible solutions.
@dannyjohnsonsgarage
Жыл бұрын
Yeah, they are triggered easy for anything with a sensor or fluid level. Mine turned off with the circle technique kzread.info/dash/bejne/fmyHkq-jpqq2Y6w.html
THANK YOU MY G! MAKE SUM VIDEOS LIKE THIS SO FCKING HELPFUL THE EXPLANATION CLEAR AF
Just had this, and this tips really work. Thanks man!!!
Danny your a real one
my 350Z is doing the same thing, I will try those tomorrow
Thank you!! It’s helped 😭😭
رحم الله والديك
Have had my car 15 years and always wondered what that “fart” sound was…ABS system testing. Thanks
@BETONUSGAMBLING
2 жыл бұрын
FACTS
Gracias !!! Me ayudo mucho su video y me ahorro mucho dinero 😊.
ok thank you Danny I was trying not to spend so much on it I was told it might cost me 12 to 15 hundred just to replace it
Great Video, Thanks for That Info..
Thanks so much bro good Chanel
This worked for my 2008 infiniti g35x. Thanks a lot was worried about these lights for a few months but thanks to u problem was fixed. Low break fluid. Saved me lots of money This guys the 🐐🐐🐐🐐🐐
Thank you. The solution to my issue was an easy fix when I discovered that it was a low coolant level that was causing my ac to blow hot air. 👍
@dannyjohnsonsgarage
4 жыл бұрын
Richard Herrera I’m glad the video helped 😉
@urielcastorena6094
2 жыл бұрын
Im having to fill up my coolent over and over and i seen on ac line like if coolent was coming out of it idk what to do
Thanks mind started wondering hard, gave me a sign relief and that’s exactly what it was piece broke off
I have a 2006 G35X and the Slip, VCD Off and Brake lights all came on this morning. I read it can be as simple as being the car needs break fluid to worn break pads etc. I had mine towed to a trustworthy mechanic and hopefully I’ll have it back in a few days. Cars are fun...until they start things like this.
@Slps
Жыл бұрын
What was the issue? My g35x is doing it rn
Low Battery and or "Low brake fluid" Fixed both. Than did the braking technique. Both Light's turned off after doing the braking technique while I was driving. "Sweet" Thanks.
@theotf4lifemgtteam450
3 жыл бұрын
what is the breaking technique?
@StacyTheRooster
3 жыл бұрын
@@theotf4lifemgtteam450 You brake while turning a sharp turn than drive straight.
@theotf4lifemgtteam450
3 жыл бұрын
Stacy the Rooster its ok i fixed it witout needing to do any of this lol
Thank you so much
Thank you so much for posting that. It worked!!!
Omg thanks I always heard that weird sound now I k ow its just the abs test
Thank you very much
Nice video
This worked for me. Thank you so much!!!!
Good s!#! Sir, Quick fix on my Gf's daughters car I appreciate thanks for the tips! 👊🏼⚡️
You’re the man! Thank you. I recently replaced camshaft sensor b1 on 2008 fx 35. Since then vdc, slip lights won’t turn off and its been stalling in motion. Added some coolant and battery was unplugged for 10+ minutes. Should be good now. Do you have recommendation on fuel saving? Recently changed both air filters and where am I is extremely cold with traffic jam. Do you recommend fuel injector cleaning additive?
@dannyjohnsonsgarage
Жыл бұрын
I would only suggest adding some sea foam to the gas tank only (one gallon of gas for each ounce, so you’ll want to put it in when filling the tank). Otherwise, use the cruise control when you are driving steady and that’s the best milage you’ll get. It does make a difference
Hey the light is flashing it means you have a tire low Make sure your 4 tires are at 35 psi It can make all that lights come on That happened on my car One of my tire was low on air I put 35 psi I turn off the car then turn on and not more lights!
It could also be the abs relay if the lights keep coming back
Thank you thank you!💜💜💜💜💜💜💜💜💜💜💜💜
I have a 2003 Nissan murano. With the same problem. I Just add brake fluid and took care of the problem
@dannyjohnsonsgarage
5 жыл бұрын
Juan Burciaga Nice! 👍🏼
@red_day6097
4 жыл бұрын
How low was your fluid?
Muy bien 👍
Very help for my car ABS😁😁😁
A+
Thanks so much! Worked like a charm on my son's 2005 Infinity G35X with 135k miles. All fluid levels were correct - not sure what causes this.
@dannyjohnsonsgarage
Жыл бұрын
It can also be a dirty wheel speed sensor or a sensor like the cam position, crank position, mass airflow, etc
Very good
@dannyjohnsonsgarage
4 жыл бұрын
Adnan Alsalitty Thank you. I’m glad you enjoyed it.
thanks for sharing sir,i have a 2015 quest and after that freezing temperature here in chicago that light and brake light would come on on cold days,in the summer it would not..i have to try what you did..thanks so much
@dannyjohnsonsgarage
4 жыл бұрын
I’m glad it worked. Sometimes it just needs a reset when nothing is really wrong. Take care!
Brake fluid was low (almost time for new brakes). Thanks!
I’ve had the same thing happened to me several times. Went with intuition once I learned where the noise was coming from and figured out a method that actually works ever time! Whenever I hear that sound and see all the lights come on, I quickly find a spot to pull over and turn my car off. I pump the brakes a few times and then start my car and put it in reverse. I drive back about 10 feet or so and then put it in drive and either drive to wherever I’m going or I will drive forward for a little bit and then stop and turn off my car again. Once you’ve done that and turned it back on, the sound will go away but the lights will stay on for a few minutes. If it doesn’t work, try it again. If it’s still on, you might need to look into it. Hope this helps you guys!
@dannyjohnsonsgarage
5 жыл бұрын
Good advice. Essentially you are having the car run an abs test. This is the concept for driving in a circle or starting the car and driving off. You’ll hear the psssssh sound as it tests.
@edelynenicolas
5 жыл бұрын
Girrlll..... Thank you! I did it and it worked!!
@modernvintagelifestyles
Жыл бұрын
I have a 2009 Infiniti FX35 that is making this the buzzing sound a few seconds after I drove off. This fix method did not work, unfortunately.
Great video. I started with checking fluids. My power steering was a little less than half full. Topped it off and it’s all good now. If it comes back on, I’ll try disconnecting the battery. I don’t know if it’s related but after VDC and Slip came on, I got a flashing air bag light. I found another video how to fix that and it worked. I have a 2008 Nissan Pathfinder so at this point it’s a 13 year old vehicle. It’s just gonna have issues. Luckily KZread helped me fix box of them. Great video!
@dannyjohnsonsgarage
2 жыл бұрын
I’d look into this just as an option kzread.info/dash/bejne/qaalp7CuftfUl7A.html
this just happened the other day to me it's the craft shaft position sensor all the lights gone now the shop fixed mines yall welcome 🎉🎉❤
@dannyjohnsonsgarage
2 жыл бұрын
That, as well as many other sensors or fluid levels can cause the lights to come on. Great job finding the issue 👍🏼
@youngmack5206
2 жыл бұрын
@@dannyjohnsonsgarage u right I forgot to add that in 🤜🏿🤛
I dont have that humming noise but ill try this later... I have had all these 3 lights the past 2 years lol... Car is running fine but of ocurse no traction control or ABS...
Thanks! Had 2 out of 3, low brake fluid & power steering. Topped off both and lights went out. I'm sure the Stealership would have told me I need to replace all bearings and ABS sensors for $1,200.
@dannyjohnsonsgarage
5 жыл бұрын
TOMCAT631 They wanted $80 for less than one ounce of brake fluid for the power steering- after I told them eagan was wrong (my father in law took our car in without us knowing when he borrowed it).
@dannyjohnsonsgarage
5 жыл бұрын
TOMCAT631 make sure you see my other videos on this car! kzread.info/head/PLIjr-uSYDZi6cuomOpHL7rGWNEbQUmbvy
My daughter cat did this when the temperature got down to 19 degrees. We will try to unhook the battery and see what it does. Thanks for the input.
It could be the brake pedal switch, any ground wire under the hood or loose battery
I tried to do this and it came back on so many times...I have had a problem for a year and a half and taken my car to several mechanics.... and had to do a manual reset everytime before I start the car just for me to figure out it was a position sensor...the position sensor fixed my problem and I can start my car like normal again
@strappadostrap7350
2 жыл бұрын
Before changing it did it crank long?
Hey Danny I hope to hear from you soon for I am stuck In a hard spot. This wouldn't be so hard if I had access to a code scanner but i do not.. none of my neighbors have one and I am almost an hour away from the nearest shop with the broken vehicle being my only one at the moment. My wife had the 03 Infiniti G35 at work and she called me saying there was a VDC, Slip & At Check and check engine light and the oil light was on. All the resivors were about half full and the oil maybe needed half a quart if that. The blinkers, taillights and the head lights (50%) of the time do not work. The car does not run very good cant make it to work until it's fixed. My neighbor is running me to advance 1 time get parts. If it's not fixed or I guess wrong im fuced. My final guess before I go is cam shaft sensor. Let me know what you think
@dommccloggan2414
10 ай бұрын
What was your issue??? My cam and crankshaft sensors need replacing
Thanks, you safeme Ni ssan Pathfider same problem.
@dannyjohnsonsgarage
4 жыл бұрын
I’m happy to hear that. See my other Pathfinder videos kzread.info/head/PLIjr-uSYDZi7UBMvxfWAJfoAVTrq_5pXC
I came here to learn how to make my car less safe, i learnt how to keep it safe
Thank you sir!!
Question random shutdown and trouble starting here and there. Same lights. 06 m35x infinity Changed crack shaft sensor no go. Cam shaft sensors next? Sez there is a left and a right one.
I saw that 10mm craftsman wrench 🔧
Check your brake lights. The fuse (10 amp) was blown causing the safety feature to lock the transmission.
@dannyjohnsonsgarage
4 жыл бұрын
E Gonzalez That’s crazy!
@michaelserrano7097
4 жыл бұрын
The heck!
@red_day6097
4 жыл бұрын
Wheres all those fuses at? Under the hood? I drive a 03 g35
@Purosabor73
4 жыл бұрын
@@red_day6097 They're behind the driver's side kick panel to the left of the foot pedals.
Many thanks. It worked on my infiniti fx35. All lights are off.
@jeanniebowman1699
2 жыл бұрын
I have a 05 Nissan psthfinder both lights are on so we unhooked the battery cable for like 20 minutes they arevdtill on so im going to find a place where I can drive 20 mph. Fir about 15 minutes and the stop and turn it off and then start it up again. I can t afford to put any more money in it
@jeanniebowman1699
2 жыл бұрын
Please help...is this what I need to do I am a woman ive put new breaks all around new tires all around new rotors all around and the front end lined up. Right St 1700.00 bucks not counting what I paid fir it
@jeanniebowman1699
2 жыл бұрын
So I pray this works thanks all!!!
If you cannot take off the light with scanner tool does it refer to faulty sensor?
Ok Danny just watched video today and you gave great info....but what you think the problem is if it's not starting back up. The security red light is not on and the key will not turn
@dannyjohnsonsgarage
4 жыл бұрын
Gavin Hampton You were saying the key is blocked and will not turn? Try slightly turning the steering wheel and then trying to turn the key
It just happened to mine this morning, didn't disconnect anything , mine is 2006 auto coupe , I just switched transmission (D) to tiptronic (manual) and they all disappeared at once lol
That was very cool!!! I’ve a 2004 g35 my my trail light/ park light/ side marker light/ centre console/ don’t works and only one day running light work!! Even in the night? What you think?
@dannyjohnsonsgarage
5 жыл бұрын
Sydon Atkins I have replaced that bulb before. Very easy, just unplug it
@issonlovegod6540
5 жыл бұрын
Danny Johnson how do you unplug these especially my right running day light just don’t turn on
@dannyjohnsonsgarage
5 жыл бұрын
Sydon Atkins For the actual headlight you’ll need to remove the headlight itself
@dylanfamo
4 жыл бұрын
Have u added a aftermarket radio? If you did. You probable grounded the Illumination light wire. If u ground that wire no lights will work.
@red_day6097
4 жыл бұрын
Yeah u got a bad cam shaft position sensor.
Just got my fixed to day to stop all this get ur crank angle sensor fix.and car back up to power runs fine
I have a 03 FX45, recently the ABS VDC and SLIP lights came on my dash, along with my windshield wipers not working, and front headlights go on even when switch is in off position. This all happened the same time. Any suggestions?
I saw the flat tire sign ON. Please let us know if you have info on that to put Off. Thanks brother
@dannyjohnsonsgarage
3 жыл бұрын
If the tire is full it’s most likely the sensor that is battery operated. The battery will die and it’s part of the valve stem so you have to remove the tire kzread.info/dash/bejne/oImCpth-qrjQmKw.html
I have a 2007 Infiniti fx35 and my mph just stopped working then the abs and slip light came on then I turned my car off and it went off but my mph still doesn’t work any suggestions?
Cool vid thank you for the steady hand !! My 2005 fx35 dies in traffic and then starts back up and drives cool but then the engine , vdc , and slip light come on
@FierceSkatin
4 жыл бұрын
Legendary Lion throttle body
@Lee-cy7df
4 жыл бұрын
Throttle body sensor
If VDC, and Airbag signals can not be seen on dashboard, while they should have appeared on dashboard and disappears when you switch on a car, what shall be the problem? Is it possible their led lights might have blown out? Any ideas please on how to bring them back
Good evening, I use an online translator, so forgive me if the translation is incorrect. I have a Nissan Skyline v36 of 2007, there was a regular gearbox without blocking, I looked at one of the descriptions on this forum, where a person tells how he cut the black wire on the G sensor and connected it to the toggle switch and did the same. it didn’t help, slip lights up on the scoreboard and the car doesn’t go into a skid, I decided that it was because of the gearbox, I bought a gearbox with a lock, but the problem is the same, the car just starts to skid and the damn “slip” lights up, the car instantly stops “drifting” ", can you tell me what's the matter? How to bypass this security system, maybe you need to cut the wiring with a different color?
Awesome video, quick question. I was driving and all the sudden I couldn't accerate anymore. I was able to press on the gas pedal and cruise at 5MPH, but the slip and that kicked on. I let it sit off for a bit, but I put a coolent leak to patch this crack so there was no coolent. I do think it ran out of coolent for the radiator and that's why that happen. Any idea?
@dannyjohnsonsgarage
5 жыл бұрын
The car likely went into “limp mode.” Once all fluids are full you’ll need to take the battery cable off and let it reset for 10 minutes.
@theripper121
5 жыл бұрын
If you go into limp mode and have little to no engine power and the lights light up like xmas trees your service engine soon light and slip lights are on its more than likely one of your camshaft or crankshaft angle sensors on the fritz. In that case I'd try to have the engine code pulled from autozone or a similar outfit. If it's one of the camshaft angle sensors the code will show which one (car has 2). If the code points to crankshaft angle sensor there's only one. Either one of those 3 sensors going out can cause your loss of power and it would be the first thing to check as they are know to be problematic on g35's. About 65 bucks will get you a new sensor and they aren't too bad to replace yourself.
@dannyjohnsonsgarage
5 жыл бұрын
theripper121 Mine also went in to limp mode from the MAF being dirty. Came up as the code as well. Cleaned it and it was fine after that.
when you start you car are you pressing the brake?? because i have these lights now and i didnt have them before
@jeanjacque1577
3 жыл бұрын
Abs relay . You need the codes scanned. What he did is just a system test and reset . It's not a fix. You need a scanner that reads abs codes. Just repaired mine and it was the abs relay
Hi Danny, My 07 FX35 started doing exactly what your video showed. I checked all fluids include oil which was very low. I disconnected negative terminal for 15 minutes. I was hoping... but no dice. There must be something more. I even put new front pads, rotors and hardware since it was needed anyway. My lights are all on when I first start up. If I travel down my driveway and hit the brakes, even lightly, it does the ABS pulsing and then lights go out. But, when I start down the road I hear clicking on front driver's side, in time with the wheels turning and after about couple hundred yards, light all come back on and clicking stops. If I don't hit the brakes when I first start up, the vehicle feels like it is loosing power, bucking and just can't get to speed. Like a limp mode.
@dannyjohnsonsgarage
Жыл бұрын
You could try bleeding the brakes, changing the fluid level. If not it may be the abs pump where you hear it do the swooosh test sound. Unfortunately they are expensive kzread.info/dash/bejne/mml8uJt9YtbLqtY.html
@georgesuroviec6229
Жыл бұрын
I bled brakes including a total fluid flush. Still N.G. I have a AWD light on besides the ABS, VDC off and SLIP. I ordered new front sensors to try that. The old ones are frozen in and will need to be drilled out. I can get around as is once the pump does it thing for about 15 seconds then I get power back to the engine and able to speed off. The noise that the pump first goes through sounds like a loud ticking clock.