It may not cost as much as you'd think, to turbo your Tsx!
Жүктеу.....
Пікірлер: 99
@BrianFromBoise3 жыл бұрын
Holy sheeit that was one hell of a punch from 50 to 100 in like 3 seconds. Very impressive gain.
@whf38262 жыл бұрын
The header style works by timing the pressure waves coming from each cylinder during the combustion cycle.
@ahmadamir16943 жыл бұрын
Best channel for TSX Content. It’ll blow up soon
@RuskiRedneck
3 жыл бұрын
Appreciate it❤️ I need to quit slacking and start keeping up on the content.
@Dan__00123 жыл бұрын
Thankfully I didn’t have to change out my clutch! I turbocharged my automatic tsx and it came out amazing. 14psi and 320whp
@RuskiRedneck
3 жыл бұрын
Right on! I didn’t have good luck turbo charging my auto. Kept getting trans code and after changing everything I could I gave up and went manual.
@Dan__0012
3 жыл бұрын
@@RuskiRedneck I’ve been wanting to go manual but I want a parts car either everything all together, ecu, harness and tranny. I don’t want to play leggos and try to piece it all together. But I went with the cxracing kit and god was it awful. Downpipe didn’t fit what so ever. The log manifold was shit. Then the wastegate took a shit. Then it was a pain in the ass to get under the car to remove the wastegate. Finally I went with tial BOV and tial WG and then I finally bent a valve. So I just rebuilt my head and I’m slowly piecing it back together. I also changed to sidewinder now so I’m excited to see when I get it back together how much power it makes. I don’t want to go over 350whp cause I hear the auto trannys don’t hold up around that power
@Dan__0012
3 жыл бұрын
@@RuskiRedneck if you want to check the build out my Instagram is Carral_305
@RuskiRedneck
3 жыл бұрын
@@Dan__0012 side wonder you’ll make 400-450 on 14psi so be careful. That log suffocates the k24
@HollyHoodRiek
2 жыл бұрын
Can you tell me a list of everything you had to buy
@darryl92443 жыл бұрын
subscribed for the rtsx content 👌🏽
@geoffreym27692 жыл бұрын
So many joins on that intercooler piping, I'd run a genuine wastegate (When they fail, they either don't boost or more commonly over boost and unless you have boost cut setup, it'll take out your motor)Why not use a cheap fuel rail and spend the saving on the wastegate. the other thing I always buy genuine is the fuel pressure regulator
@jackbolongaita41539 ай бұрын
You have one of the nicest TSX's I've seen man.
@RuskiRedneck
9 ай бұрын
Thank you.
@k24in313 жыл бұрын
Thank you for the info and content
@RuskiRedneck
3 жыл бұрын
You bet
@sodjazero3 жыл бұрын
Nice Broski! Keep the vids coming
@RuskiRedneck
3 жыл бұрын
Thanks! Will do!
@RishMedia3 жыл бұрын
Nice video man good info! That was the plan on running the CX racing piping and intercooler, was going to potentially run the log manifold but from another guy it’s a really tight fit and the turbo I want wouldn’t end up fitting lol. Might just get the plm sidewinder and have the welds touched up perfect any potential cracking.
@marlontucker5419
3 жыл бұрын
What size turbo was u going to run with the log style manifold
@RishMedia
3 жыл бұрын
@@marlontucker5419 I wanted to do precision’s 6262 Guys running the cast manifold with a t3 precision 56 or 57 and said was already a tight fit.
@khalidtrevor9449
2 жыл бұрын
i dont mean to be so off topic but does someone know of a method to log back into an Instagram account..? I somehow lost the login password. I love any tips you can give me.
@shilohkristian966
2 жыл бұрын
@Khalid Trevor Instablaster :)
@khalidtrevor9449
2 жыл бұрын
@Shiloh Kristian thanks for your reply. I got to the site through google and Im in the hacking process now. I see it takes quite some time so I will get back to you later when my account password hopefully is recovered.
@russishenin10563 жыл бұрын
Well done!!!
@Branflakes663 жыл бұрын
Nice and informative video 🔥
@laribud082 жыл бұрын
Privet, I am on ur side want to buy one of these Honda k24 and tune it...
@chado745 Жыл бұрын
I currently have the cx racing kit on.. I would like to know my best option for sidewinder header
@freddyperez46122 жыл бұрын
Where u got those lights for the grill
@Markosonez3 жыл бұрын
Noice👍😅🔥🔥
@smurftech91913 жыл бұрын
More tsx content ! Keep it up 👍
@RuskiRedneck
3 жыл бұрын
Will do!
@mojojojjj2 жыл бұрын
where did you buy all the red trim? looks beautiful bro & great vid
@RuskiRedneck
2 жыл бұрын
Thank you! It’s a red carbon fiber wrap. I think I’m going to attempt to hydro dip instead. The wrap looks good for the most part except on some of the hard corners
@S7SGamerHD2 жыл бұрын
Great Info. Im doing this to my tsx. Great content. How long did it took u to get everything done?
@RuskiRedneck
2 жыл бұрын
Appreciate the support. It took me a few months. With there not being hardly any info out there for the tsx I had to take my time to figure it out.
@joserribera48888 ай бұрын
And the ecu wha u need to put in more fuel ⛽️
@texasmadeMx777 Жыл бұрын
If I wanted to go with a turbo build what are the prep parts I need to upgrade on my engine/ tranny to have sustain all that power?
@RuskiRedneck
Жыл бұрын
Depends on the power level you’re going for. 400hp should be fine with a good tune and fuel system. 500hp I’d go e85. Anything over I’d build the block sleeves pistons rods and head and run e85 1500-2000cc injectors 450walbro fuel pump.
@eduardoalvarado79103 жыл бұрын
What are the lights in the front under the hood called?
@keoclements7918
3 жыл бұрын
Did you find out??
@kennygonzalez91173 жыл бұрын
Can you make a part list and where to buy.
@RuskiRedneck
3 жыл бұрын
For what parts? I have a parts list in my earlier video.
@keoclements79183 жыл бұрын
What are those lights in the front and how’d you get them????
@user-hh4hc2lt6e
Жыл бұрын
Just halo/ circle lights around the horns lol
@Impulse_Society9 ай бұрын
Did I hear small fuel cuts
@calvinshea8822 жыл бұрын
Was wondering if I could ask some questions about the cx build and how you ran. If you could contact me that would be very helpful
@RuskiRedneck
2 жыл бұрын
What’s your Snapchat?
@-dante8085
2 жыл бұрын
@@RuskiRedneck hey can you help me also?
@bkol7153 жыл бұрын
He’s got a serious chin
@XavierJMoore-nn5ez Жыл бұрын
I’m so lost I have a 2004 Acura TSX 5speed automatic. Where do I start?
@jaeguyoon
9 ай бұрын
I would get hondata flashpro, so you can have some fun while you start piecing up your kit (turbo, manifold, ic, pipings, injectors, oil feel and return lines, and lastly you prob want to upgrade your oil pump to k20a2 oil pump).
@jb65792 жыл бұрын
Got any recommendations for a 2nd gen tsx ? Lookin to go turbo but don’t know where to start
@RuskiRedneck
2 жыл бұрын
What motor?
@jb6579
2 жыл бұрын
@@RuskiRedneck k24z3
@abrica1stacc8622 жыл бұрын
What kinda mpg can one expect from this setup?
@RuskiRedneck
2 жыл бұрын
You know I never actually calculated that. The mph gauge on the cluster reads wrong now that I’m turbod. Not sure why but it says I get like 60mpg🤣 I’ve got a Heavy foot so I’m burning thru some fuel.
@RoosterfishhGaming3 жыл бұрын
Hello! I am buying the cx turbo kit and I have a few questions. I currently have RDX 410cc injectors. I won’t be running too much boost so is it ok if I can keep those injectors and not use an aftermarket fuel pump, fuel return, and fuel rail?
@RuskiRedneck
3 жыл бұрын
You will need bigger injectors unless you are running like 2-3psi. Talk to your tuner You might be okay with your set up for a bit. But it’s always better to have plenty of fuel.
@marlontucker54193 жыл бұрын
How much hp your car have now
@RuskiRedneck
3 жыл бұрын
The car hasn’t hit the dyno yet. My guess is low to mid 400s. There’s still some fine tuning that could be done on the dyno so I’m keeping the boost and limiter down for now.
@shotbyqory31613 жыл бұрын
What’s your wheel specs
@RuskiRedneck
3 жыл бұрын
18x10.5
@erijdiaz1005 ай бұрын
What did you bore it too
@RuskiRedneck
5 ай бұрын
.5 over stock
@flosgarage233 жыл бұрын
Look at tourqamp lol
@isayogmez84993 жыл бұрын
recommendations for A/Ts boosting? besides the obvious why would you do that lmfao
@RuskiRedneck
3 жыл бұрын
I would say go with a super charger with an auto trans.
@SoulEraser000
3 жыл бұрын
@@RuskiRedneck Why do you say supercharger for auto?
@RuskiRedneck
3 жыл бұрын
@@SoulEraser000 because the tsx auto trans doesn’t handle power too well. Supercharger gives power more gradually. Kinda eases into it. Where as a turbo will kick in later and a lot harder causing a lot of stress to the trans.
@Kr0n3kLe
3 жыл бұрын
Do a manual conversion
@SoulEraser000
3 жыл бұрын
@@Kr0n3kLe that's like the cost of boosting your car lol
@k24in313 жыл бұрын
0-100mph video?
@RuskiRedneck
3 жыл бұрын
ill have to take a trip to Mexico this weekend
@VangBill963 жыл бұрын
Your voice don’t fit you ngl but I’m here for the content 🤷♂️
@RuskiRedneck
3 жыл бұрын
How so? Is it because English is my second language or are you thinking more along the lines of a voice changer.
@Damir72rus3 жыл бұрын
Русский?)))
@RuskiRedneck
3 жыл бұрын
Да
@Damir72rus
3 жыл бұрын
@@RuskiRedneck красавчик, не ожидал контента от наших за бугром(про Хонду)!))
@ryannitoi29933 жыл бұрын
i mean for all of this work i'd almost just rather sell the car and buy something faster
@RuskiRedneck
3 жыл бұрын
What’s the fun in that? I enjoy the work. Even with all the mods it won’t be the fastest or the best chassis to build but I enjoy it.
@gabebittick61642 жыл бұрын
cheap lmao
@j0cr0z Жыл бұрын
Could I turbo an automatic 4 cylinder tsx
@RuskiRedneck
Жыл бұрын
Yes you can. Several people have successfully done it
Пікірлер: 99
Holy sheeit that was one hell of a punch from 50 to 100 in like 3 seconds. Very impressive gain.
The header style works by timing the pressure waves coming from each cylinder during the combustion cycle.
Best channel for TSX Content. It’ll blow up soon
@RuskiRedneck
3 жыл бұрын
Appreciate it❤️ I need to quit slacking and start keeping up on the content.
Thankfully I didn’t have to change out my clutch! I turbocharged my automatic tsx and it came out amazing. 14psi and 320whp
@RuskiRedneck
3 жыл бұрын
Right on! I didn’t have good luck turbo charging my auto. Kept getting trans code and after changing everything I could I gave up and went manual.
@Dan__0012
3 жыл бұрын
@@RuskiRedneck I’ve been wanting to go manual but I want a parts car either everything all together, ecu, harness and tranny. I don’t want to play leggos and try to piece it all together. But I went with the cxracing kit and god was it awful. Downpipe didn’t fit what so ever. The log manifold was shit. Then the wastegate took a shit. Then it was a pain in the ass to get under the car to remove the wastegate. Finally I went with tial BOV and tial WG and then I finally bent a valve. So I just rebuilt my head and I’m slowly piecing it back together. I also changed to sidewinder now so I’m excited to see when I get it back together how much power it makes. I don’t want to go over 350whp cause I hear the auto trannys don’t hold up around that power
@Dan__0012
3 жыл бұрын
@@RuskiRedneck if you want to check the build out my Instagram is Carral_305
@RuskiRedneck
3 жыл бұрын
@@Dan__0012 side wonder you’ll make 400-450 on 14psi so be careful. That log suffocates the k24
@HollyHoodRiek
2 жыл бұрын
Can you tell me a list of everything you had to buy
subscribed for the rtsx content 👌🏽
So many joins on that intercooler piping, I'd run a genuine wastegate (When they fail, they either don't boost or more commonly over boost and unless you have boost cut setup, it'll take out your motor)Why not use a cheap fuel rail and spend the saving on the wastegate. the other thing I always buy genuine is the fuel pressure regulator
You have one of the nicest TSX's I've seen man.
@RuskiRedneck
9 ай бұрын
Thank you.
Thank you for the info and content
@RuskiRedneck
3 жыл бұрын
You bet
Nice Broski! Keep the vids coming
@RuskiRedneck
3 жыл бұрын
Thanks! Will do!
Nice video man good info! That was the plan on running the CX racing piping and intercooler, was going to potentially run the log manifold but from another guy it’s a really tight fit and the turbo I want wouldn’t end up fitting lol. Might just get the plm sidewinder and have the welds touched up perfect any potential cracking.
@marlontucker5419
3 жыл бұрын
What size turbo was u going to run with the log style manifold
@RishMedia
3 жыл бұрын
@@marlontucker5419 I wanted to do precision’s 6262 Guys running the cast manifold with a t3 precision 56 or 57 and said was already a tight fit.
@khalidtrevor9449
2 жыл бұрын
i dont mean to be so off topic but does someone know of a method to log back into an Instagram account..? I somehow lost the login password. I love any tips you can give me.
@shilohkristian966
2 жыл бұрын
@Khalid Trevor Instablaster :)
@khalidtrevor9449
2 жыл бұрын
@Shiloh Kristian thanks for your reply. I got to the site through google and Im in the hacking process now. I see it takes quite some time so I will get back to you later when my account password hopefully is recovered.
Well done!!!
Nice and informative video 🔥
Privet, I am on ur side want to buy one of these Honda k24 and tune it...
I currently have the cx racing kit on.. I would like to know my best option for sidewinder header
Where u got those lights for the grill
Noice👍😅🔥🔥
More tsx content ! Keep it up 👍
@RuskiRedneck
3 жыл бұрын
Will do!
where did you buy all the red trim? looks beautiful bro & great vid
@RuskiRedneck
2 жыл бұрын
Thank you! It’s a red carbon fiber wrap. I think I’m going to attempt to hydro dip instead. The wrap looks good for the most part except on some of the hard corners
Great Info. Im doing this to my tsx. Great content. How long did it took u to get everything done?
@RuskiRedneck
2 жыл бұрын
Appreciate the support. It took me a few months. With there not being hardly any info out there for the tsx I had to take my time to figure it out.
And the ecu wha u need to put in more fuel ⛽️
If I wanted to go with a turbo build what are the prep parts I need to upgrade on my engine/ tranny to have sustain all that power?
@RuskiRedneck
Жыл бұрын
Depends on the power level you’re going for. 400hp should be fine with a good tune and fuel system. 500hp I’d go e85. Anything over I’d build the block sleeves pistons rods and head and run e85 1500-2000cc injectors 450walbro fuel pump.
What are the lights in the front under the hood called?
@keoclements7918
3 жыл бұрын
Did you find out??
Can you make a part list and where to buy.
@RuskiRedneck
3 жыл бұрын
For what parts? I have a parts list in my earlier video.
What are those lights in the front and how’d you get them????
@user-hh4hc2lt6e
Жыл бұрын
Just halo/ circle lights around the horns lol
Did I hear small fuel cuts
Was wondering if I could ask some questions about the cx build and how you ran. If you could contact me that would be very helpful
@RuskiRedneck
2 жыл бұрын
What’s your Snapchat?
@-dante8085
2 жыл бұрын
@@RuskiRedneck hey can you help me also?
He’s got a serious chin
I’m so lost I have a 2004 Acura TSX 5speed automatic. Where do I start?
@jaeguyoon
9 ай бұрын
I would get hondata flashpro, so you can have some fun while you start piecing up your kit (turbo, manifold, ic, pipings, injectors, oil feel and return lines, and lastly you prob want to upgrade your oil pump to k20a2 oil pump).
Got any recommendations for a 2nd gen tsx ? Lookin to go turbo but don’t know where to start
@RuskiRedneck
2 жыл бұрын
What motor?
@jb6579
2 жыл бұрын
@@RuskiRedneck k24z3
What kinda mpg can one expect from this setup?
@RuskiRedneck
2 жыл бұрын
You know I never actually calculated that. The mph gauge on the cluster reads wrong now that I’m turbod. Not sure why but it says I get like 60mpg🤣 I’ve got a Heavy foot so I’m burning thru some fuel.
Hello! I am buying the cx turbo kit and I have a few questions. I currently have RDX 410cc injectors. I won’t be running too much boost so is it ok if I can keep those injectors and not use an aftermarket fuel pump, fuel return, and fuel rail?
@RuskiRedneck
3 жыл бұрын
You will need bigger injectors unless you are running like 2-3psi. Talk to your tuner You might be okay with your set up for a bit. But it’s always better to have plenty of fuel.
How much hp your car have now
@RuskiRedneck
3 жыл бұрын
The car hasn’t hit the dyno yet. My guess is low to mid 400s. There’s still some fine tuning that could be done on the dyno so I’m keeping the boost and limiter down for now.
What’s your wheel specs
@RuskiRedneck
3 жыл бұрын
18x10.5
What did you bore it too
@RuskiRedneck
5 ай бұрын
.5 over stock
Look at tourqamp lol
recommendations for A/Ts boosting? besides the obvious why would you do that lmfao
@RuskiRedneck
3 жыл бұрын
I would say go with a super charger with an auto trans.
@SoulEraser000
3 жыл бұрын
@@RuskiRedneck Why do you say supercharger for auto?
@RuskiRedneck
3 жыл бұрын
@@SoulEraser000 because the tsx auto trans doesn’t handle power too well. Supercharger gives power more gradually. Kinda eases into it. Where as a turbo will kick in later and a lot harder causing a lot of stress to the trans.
@Kr0n3kLe
3 жыл бұрын
Do a manual conversion
@SoulEraser000
3 жыл бұрын
@@Kr0n3kLe that's like the cost of boosting your car lol
0-100mph video?
@RuskiRedneck
3 жыл бұрын
ill have to take a trip to Mexico this weekend
Your voice don’t fit you ngl but I’m here for the content 🤷♂️
@RuskiRedneck
3 жыл бұрын
How so? Is it because English is my second language or are you thinking more along the lines of a voice changer.
Русский?)))
@RuskiRedneck
3 жыл бұрын
Да
@Damir72rus
3 жыл бұрын
@@RuskiRedneck красавчик, не ожидал контента от наших за бугром(про Хонду)!))
i mean for all of this work i'd almost just rather sell the car and buy something faster
@RuskiRedneck
3 жыл бұрын
What’s the fun in that? I enjoy the work. Even with all the mods it won’t be the fastest or the best chassis to build but I enjoy it.
cheap lmao
Could I turbo an automatic 4 cylinder tsx
@RuskiRedneck
Жыл бұрын
Yes you can. Several people have successfully done it