Very helpful. I've seen several videos on the topic, but this one is well thought out & well presented. Thank you

@guzzifabrication3448

27 күн бұрын

Thank you, Sir, I very much appreciate that comment !

Awesome video. I'm new to tube bending and you taught me well.

@guzzifabrication3448

21 күн бұрын

That's awesome !! sounds really complicated at first but with some practice you can make very precise bends.

The best tutorial yet, thanks for providing this video.

@guzzifabrication3448

4 ай бұрын

It was alot of fun making the video, I hope it helps !

happy to be the 1K like!! nice vid!!

@guzzifabrication3448

Ай бұрын

That is awesome ! Thank you !!!

Outstanding Explanation and Presentation. 😎

@guzzifabrication3448

6 ай бұрын

Thank you Sir !

Thanks for teaching. Very helpful.

@guzzifabrication3448

Жыл бұрын

Awesome ! Hey thanks for watching !!!

Man solid video! Just got my swag off road bender and have been looking for something like this! Most of my bends are not 90-degrees so it will take some practice but this was great!

@guzzifabrication3448

3 ай бұрын

Nice ! make a gauge in your size tubing and your good to go.

Excellent instruction!

@guzzifabrication3448

2 жыл бұрын

Thanks !

Good tips

hello Guzzi: after watching a few other KZread videos on bending tubing, your video is much clearer than the others.....I am still having to watch a 2nd and 10th time to get it all in this old brain..... unfortunately, I am using a Hossfeld bender, and the tubing does not get pulled around like you style bender, I think I have seen them referred to as a Pipe bender....due to the fact the die stays stationary ....and of course, there is not degree scale.....thanks for all the great information......Paul in Florida

@guzzifabrication3448

5 ай бұрын

👍

Very good clear explanation. 👍

@guzzifabrication3448

7 ай бұрын

Thank you Sir

Great video!

@guzzifabrication3448

2 жыл бұрын

Thanks !

I'm still learning how to calculate a bend in metal on the benders I make. Trying to learn all the different ways. Right now I'm trying only math. Will just be using a program when making something but want to be able to calculate without it too. Thanks!

@guzzifabrication3448

Жыл бұрын

Nice !

Egggggggggggggggggggggggggggggggggggggggggggggggggggslent video. Thanx for sharing. You Rock!!

@guzzifabrication3448

5 ай бұрын

Thank you Sir !

Thanx for that

@guzzifabrication3448

8 ай бұрын

👍

I felt excited when I realized why the bend contour at the end was different before you told us hahah. I’m learning slowly but surely

@guzzifabrication3448

2 ай бұрын

I learn everyday .... Thanks for the comment !

Great video man!!! I wish I found this two days ago I would have saved myself 20’ of 1.5” 0.95 DOM 🤦🏻‍♂️

@guzzifabrication3448

Жыл бұрын

I tried to call you but you didn't answer..... no really dude that sucks we've all done it I've wasted plenty of material...

@damienmikkelsen6056

Жыл бұрын

@@guzzifabrication3448 oh man I’m sorry I missed your call.

@ypaulbrown

5 ай бұрын

@@guzzifabrication3448 well, sometimes wasting is learning......cheers....Paul

@guzzifabrication3448

5 ай бұрын

👍@@ypaulbrown

Thank you for that , well done. New subscriber , I will check to see if you have more about tube bending , I am a newbie.

@guzzifabrication3448

8 ай бұрын

Thank you Mr. Mencel !

I'd love a video on how you set the zero point, and get repeatable precision on your bend angles. I've been getting ±2° lately doing sch 40 aluminum tubing with a manual JD2 m32. Would like to get that tolerance down.

@guzzifabrication3448

6 ай бұрын

Time stamp 2:33, is that what you are looking for? or another item that can throw off the bend is not pre loading the assembly ( pushing the dies, follower, etc all to same starting point when you install the tubing.

@ar5000

6 ай бұрын

Yeah, right there. You kinda breezed over how you preload, and how you determine spring back. When I'm bending Al tubing, there's an "easy 0°", then there's "take the slack out 0°", and lastly "somewhere north of 0° but still in the spring back region (2-4°). True 0° is somewhere in there. I'm trying to figure out how to set the angle guage to 0° reliably each time I setup my bender.

@ypaulbrown

5 ай бұрын

hi AR5000, if you are using bending schedule 40 Aluminum, you are bend Pipe and not Tubing..... there is a difference in the dies......but I have found, that I can use a 1 1/2 inch tubing die, to bend 1 inch schedule 40 6061 T6 aluminum and get a good result.....the OD on 1 " pipe is 1.333 or so.... I am using a Hossfeld, which I think is harder to use for these type bends. anyway, enjoyed your comment..... Paul down in Florida......

Nice work , what brand band saw is that

@guzzifabrication3448

2 жыл бұрын

That's a harbor freight band saw, really like it

Bro. , is it better way if put a supporting rod(movable) inside of the pipe's bending zone when bend it. my thought is that below factors shall impact the unbending size calculation and dedormation of pipe after bending: 1. pipe's OD + thickness 2. bending die's size ( it's OD should be slightly bigger than pipe's OD), for example, pipe OD 1 1/4 inch+ uppper tolerance, so bending die's size should be pipe OD+upper tole.+ 0.004inch as clearance 3. bending speed need controlled 4. pipe material will also impact (hardness), so adjust process parameter above 5. lubricantion shall optimize the process

@guzzifabrication3448

Жыл бұрын

Did I not replicate the piece exactly using the gauge I made to calculate the bends??? Go build a rocket or something thanks for watching

I love the color of this pro tools bender. But it’s literally an Eastwood bender but $120 more.

@guzzifabrication3448

Жыл бұрын

I really wanted the JD squared but at the time they were back ordered

@mrmidnight32

Жыл бұрын

@@guzzifabrication3448 same with JD. Same rating as the Eastwood for $150 more and the dies from JD are WAY more expensive. I wanted a JD as wel but when it does the same job as something less expensive it’s hard to justify. And they all are a copied design off the Hossfield bender that lost its patent long ago and went into open production.

@guzzifabrication3448

Жыл бұрын

@@mrmidnight32 I really wasn't impressed with the quality of the trick tools dies they don't leave marks on the stock.... but the finish out quality on the dies is terrible in my opinion. Yeah I'm really happy with the Bender but you're right why pay more when you don't have to.... I'm All About cost-effectiveness

Dumb question... do you need to make guides at 90°, 60°, and 45° if those are your close common bends... or can you calc them all with a single 90° guide?

@guzzifabrication3448

Жыл бұрын

THanks for watching, the focus of this video is fabricating a radius gauge 1. for accuracy 2. zero material waste. To your question you could but then there would be an amount of guessing.

@fredschuttenbeld4571

3 ай бұрын

​@guzzifabrication3448 you say for zero waste, but if you make just a one of piece, now you already wasted a piece of tubing as a gauge. Also without a sample piece you still need to measure (and log) the distance of the x,y axis (to accommodate the stretch of the bend) for your initial bend. For this you may leave 1 or a couple inches extra on the end of the tube and cut it off after and thus not wasting 17 inches.

how would go about bending a 1/2" copper pipe in different diameters? say 8" 6" 4" 2"

@guzzifabrication3448

9 ай бұрын

I really don't have any experience in bending copper, I seems a conduit hand bender may work for copper. If you try it let me know how it works.

Off subject... @ "3:28" you can clearly see internal ripples!!! Does the protools suck, or was tubing too thin, or... wtf?? Thanks.

@guzzifabrication3448

Жыл бұрын

I'm using stainless tubing, if it were steel there would be less defgormation. Thanks !

Just use 1/4" latex hose in the center of the tube.

There's a few crimps on the inside of the bends. Bend with the seam on the tube facing up or down and it'll prevent crimping. Otherwise somethings a miss with the tool I suspect..

@guzzifabrication3448

2 жыл бұрын

You get a certain amount of deformation with stainless.... not so much when using steel

@GotScout

Жыл бұрын

I saw that too... horrified!!!!

@ironsled77

Жыл бұрын

JD square model definitely does not kink stainless steel.

@rickyherbold785

6 ай бұрын

He had the follower die upside down

@thenetwerx

5 ай бұрын

@@rickyherbold785how would that affect quality? Is the follower not a symmetrical shape?

Good video, but @ 2:17 you show the follower, and it is scribed "up" but you put it in down @ 2:21

@guzzifabrication3448

Жыл бұрын

Yes the follower is marked... however the follower is multi-directional, up or down is of no consequence and does not effect the bend. Thanks for watching !

Gauge, guage, gauge, guage…lol Interesting approach, thanks for posting

@guzzifabrication3448

Жыл бұрын

What would you suggest, guessing...... if you are executing precise bends this method is 100 % accurate.....

@HVAC_Tips_Tricks_Calcs

Жыл бұрын

@@guzzifabrication3448 I was commenting on the fact you are spelling gauge wrong, a couple of times. Otherwise I like the video

1:24 $100 dollar piece of sacrificial metal.

@guzzifabrication3448

Жыл бұрын

Yep thank Trump for the tariffs that are still in place causing the record high metal prices

Basically You are saying that You need to make a sample bend for every deferent Wall Thickness that You are using ⁉️

@guzzifabrication3448

2 ай бұрын

The title of the video is : Making a radius gauge to calculate a bend.

Kills me that no one seems to know how to calculate the bends with actual math and not have to always use a gage. It is easy and I am a guy who failed basic algebra in high school 35 years ago.

@guzzifabrication3448

2 жыл бұрын

All hail the math flunky!!!

@codyp3041

Жыл бұрын

You use the arc length formula?

@ar5000

6 ай бұрын

Maybe some of us do know the math and theory but are wise enough to know that the real world introduces error that is more difficult to correct for compared to...wait for it... A radius gauge.

@Afrorack

6 ай бұрын

​@@ar5000I agree...a guage with a reference point-i use the flat side of the die that touches the tube first works for real world scenarios...

So. Many. Wrinkles. Where is your wiper die?

@guzzifabrication3448

3 ай бұрын

Sounds like you're trying to fault. Find unless you're using an industrial bender, which I am not. You would know wrinkling and stainless is inherent.... So I have a question for you, spud. Where's your free video on youtube trying to help people? I looked but I couldn't find one.... It's always easy to spot people with little experience like yourself.

That’s terrible bend quality

@guzzifabrication3448

3 ай бұрын

Does captain aj stand for captain a@$ jockey? I looked, but I didn't see the video you uploaded that shows a better quality bend..... thanks for the comment and supporting the cannel a j.....

You lost me when you started using an already fabricated frame for references to start marks. You are using a known finished product to find your bend starting point. I don't have that luxury. Doesn't any one know how to calculate begining cuts to bends and material needed without cheaters ?

@guzzifabrication3448

Жыл бұрын

You could always just guess at how to achieve accurate bends....

@boonieg2460

Жыл бұрын

The title of the video is " making a radius gauge to calculate a bend " that's what he did.... are you daft?