Finally! Been watching this very interesting channel for a long time, been waiting for this. Got two of those recievers, a TX-NR579 (driving two Klipsch RB 51 used as computerspeakers), and a TX-NR 808 as main HiFi unit. Both are approx 8 years old.and they always had a lot of cooling space arround them, and were never abused. The 579 failed in 2016 and was put in a closet, and after I realized that there was an extended warranty, I send it in (2017/2018) and it was repaired (new HDMI board). Still working fine. The 808 never failed. Thanks for a very cool channel!

I really dig the no frills approach you do. You just say what you're going to do and you do it. Also, your lighting is pretty good.

I bought an Onkyo used a few years ago and it had no sound when I connected. I saw your video and decided to try your trick for the heck of it. IT WORKED!!!!! I don't care if it is a temporary fix, your video resurrected this boat anchor and made my purchase worth it. Thank you so much.

Nice customer service - it's always good to prove out the fault and provide a cost of a proper repair! Thanks for sharing.

Nice video. I've been out of repairing receivers and other things since 2001 when I was laid off and then ill after 30 years in the business. This looks more like a computer motherboard than an analog receiver to me! When I got laid off, these SMD micros were slowly populating the boards of the newer models. I've seen a lot of thermal problems on the older units of various descriptions like the one described in your video.

thats a creative and pretty cool troubleshooting trick. i love it! thanks for all your videos, you have taught me a lot about electronics over the last several years

Our family business is the rebuilding and/or repairing of 1960’s to 2000’s Harley Davidson V-twin engines and after decades of dealing with the general public I’ve learned that leveling with people and simplifying things as much as possible when explaining a technical issue is greatly appreciated. Anyone that would give this a “thumbs down” must not understand the point of many of these videos? Anyway, great video, thanks for the information. 😊

Thank you once again! I did this method to my onkyo tx-nr414 half a year ago. Few days ago I lost the audio and I did this trick again. Enjoying good music again! Thank you:)

Occasionally the BGA solder pads do not 100% flow in the cct. board manufacture and the odd ball may end up just having a ‘touch’ contact that may work and not show a fault until later. In and amongst my life as an electronic technician before retiring from the game, I was involved in a R&D and debugging role at a major digital satellite and cable receiver manufacturer and occasionally came across this problem, giving the chip a little tickle with a fine nozzle on a hot air gun sometimes cured the problem, even using an expensive professional rework station replacing. BGA (ball grid array) is a nightmare, you cannot guarantee that additional heat applied after original board flow will not damage the internal tracking of a multilayered circuit board, as you say, the bit of heat with a bit of luck will keep your board running a while but you end up repairing it as a freebie!! Keep your little films coming,I’m sure they help a lot of people

Thank you! Thanks to your video, I decided to purchase a 300w heat gun from Amazon. Just two hours ago, I tried heat gun about 3" away for about 2 minutes. I tried power on twice and both times my 808 would have sound right away from cold power on. Will see how long this lasts.

Thanks so much! I've had an Onkyo receiver sitting in my extra room for several years waiting until I could justify costly repairs, and now I have a way to potentially isolate the issue without having to take it in to someone and get charged labor for troubleshooting. Can't wait to try your solution (and if I'm lucky get another 3 years out of the receiver).

@SolidSleds

Жыл бұрын

If you haven't tried it, do it. I used my heat gun from a solder station and it fixed my Onkyo that had been setting dormant for a few years.

How could anyone give you a thumbs down for such an innovative; simple; and totally conclusive trouble shooting test? I thought that was amazing !! I do wonder where you might find programmed DSP chip replacements for any of these recent intelligent receivers ??

@kindanyume

5 жыл бұрын

idiot elieteists snob fuktards that think anythingnotdone with a fancy station that costs as much as a car just can never be good etc etc same sort od morons that buy XTZ brand thinking its cook cause they paid $$$ meanwhile reality is the exact same thing is sold under abc logo at 1/ the price and they would look down on those buting abc brnd once again there is no lack of stupidity in the universe!

@deangale4496

Жыл бұрын

And why wouldn't Texas instruments re issue one that worked

Onkyo has always had great features (10.2 sound before anyone else, etc) but I was always concerned about reliability. I ended up with a Yamaha and I love it. Thanks for the video and a cool (hot) diagnosis!

@gplusgplus2286

3 жыл бұрын

My basic year 2000 Yamaha still works. Ive had it on my TV and connected HTPC and never turn it off, right now its playing this video.

@tacofortgens3471

Жыл бұрын

Yamaha isnt like they used to be, build the same way as Onkyo's Denons and Hamron Kardons. Cheap

Blew out a JVC 87 year model monster. Took 12 speakers and one to short contact to fry it. It came on but no sound. Thing was in use 26 years. Gave it to guy next door when I moved, he probably got it to work had a number of units in his backyard garage. My other JVC still strong after 12 years but using only the speakers that came with it out the box. Nice video.

Great tip. I never thought of doing this before. It does makes sense that continuous heating and cooling would eventually crack a solder joint. Thanks for sharing.

@12voltvids

5 жыл бұрын

It is either a cracked solder joint or a cracked silicon die inside the chip.

@vdochev

Жыл бұрын

It's the interposer inside the chip. If you heat it up things expand and make contact again. The bad thing is things also shrink... So, as the owner of the video said, it's not a proper repair, you need to replace the chip with a good one. And then probably provide good ventilation when using it.

@GTAmelody

8 ай бұрын

@@vdochev I see that non-existent cooling on DSP's is the main reason of their faults?! Thank You both for your knowledge!

I might jinx it, but I gave a friend of mine my folks old 1999 Onkyo reciever and it's still kickin, and I have a used Onkyo reciever that's going strong. I hope I don't ever have this issue. Love your videos

Thank you. I watch your video yesterday and apply it in the next morning. Now it’s working. Your video was a big help. Thank you very much and more power.

I have multiple onkyo’s now. A 508 fixed the output stage. Still working great. Fixed a 313, faulty standby relais. Sold it. Now using a 607 as main home audio unit. Had no display. Fixed it. Great unit. Other units. 706 hdmi board total failure 414 working but no video. Another 313, hdmi chip fried recently. 578 also kind of fixed. Still working on it. Next to the hdmi board chips running very hot. Also the amp itself runs very hot. This is also a reason to get the unit as cool as possible. Btw dave... get a hot air station.

Great tip thanks for the information. I've just fixed my ailing Yamaha RX-V673 amplifier which also has the same chip, luckily I was directed here from the Yamaha forums.

Thanks your advice worked. Ran my heat gun over the chip for 35-45 seconds while shielding the four sides and connections are now made. Heard it click so new the switch was doing its job. Thanks again!!!!

This trick worked for me. I am from Chennai India. Great and thanks to you.

The moment where a $40 paperweight you shouldn't have bought from goodwill starts working! HOLY CRUD! Bought an HT-180 and discovered it had this exact problem. Grabbed a bulb just like you had and applied it to the chip for about 5 mins and BAM! The dumb thing works! Unreal. Great video!

@stb3265

Жыл бұрын

Lol. Me too. I got a 708 for $10 at a thrift store. I used a butane lighter to heat the chip to 380F (very carefully and using a temp gun to keep an eye on the temps). Works perfectly. If I get 3y out of it, I will be happy. If not, it was $10.

Thank you for posting !! I have the same exact receiver with the same exact problem. Going on amazon to but a heat lamp to see if it will fix it. Cheaper than buying a new receiver. Great Post thank you !!

This video helped me to identify the issue with my Onkyo TX-NL509 years later. Will try to find the parts and otherwise... Well so long Onkyo, I guess. Thanks OP!

Yeah I've seen you fix TV's as well using this method. Thanks Dave.

Great to find this after 2 different Onkyo receivers and 2k, I bought a Marantz.

I have been through so many Onkyo's. The last great trouble free one I owned was a TX NR901. Used daily until I just had to have HDMI. Even then the 901 was used in a garage setup for another 10 years with zeo problems. When I went HDMI, I decided to go with the TX SR805. I was so impressed with it that I bought a TX NR905 to get Ethernet input and moved the 805 to my front room setup. well, not soon after that the 805 video and sound. Tried to get it repaired, but Onkyo wouldn't honor. At that time I bought a TX NR807 on clearance to replace it. Not soon after the 905 lost sound. I was able to locate a TX NR5007 on closeout and picked it up. Again, Onkyo refused to fix the 905, so on the shelf it went. You know where this is going, not soon after the 807 failed. Lost Video, Ethernet and audio. I tried the 5008, but started having issues out of the gate with it and was able to return it. At this point I was done with Onkyo and switched to Denon. Of coarse the 5007 failed too, so I trashed the 805, and the 905, 807 and 5007 sat on the basement shelf. Years later Onkyo decided one time only to repair these units, but guess which model was left out? The 905 which I found to sound the best for Audio out of all of them. I sent in the 807 and 5007. The 807 is still sitting on the shelf since getting it back and I put the 5007 in my basement and it was still acting wonky when I got it back, but Onkyo refused to fix. None of the input buttons respond correctly and when you try to power down it will either turn zones 2 and 3 on or put it in pure power mode. after about 10 pushes it might finally turn off, but not before clearing all of your settings as if you did a factory reset. I would love to get the 905 back up and running and the 5007 working properly, but no one will tough them. :(

@12voltvids

5 жыл бұрын

I am currently using a 605 which was given to me last year. When my RC370 started acting up again after 3 years (after the light bulb fix) I put in the older 605 and use it just for TV sound. It doesn't work properly with analog inputs, as it won't convert them to HDMI like the 370 did so my VCR and Laserdisk is useless as they are remote mounted and not connected directly to the TV. In my setup all my equipment is in a separate closet, about 30 feet from the TV, so all switching needs to be done remotely. Since I still have analog sources, getting a new modern receiver that only has HDMI is not an option. I have resorted to plugging my VCR and Laserdisk player into an MTS stereo modulator and sending the video and audio over RF to the TV, and then the sound back to the receiver. Not an ideal setup, but at least it allows me to view VHS, Beta and Laserdisk analog sources. I don't use these much these days anyway.

i did this with a pioneer about 4 years ago. still working.

Many thanks. Worked for me on my TX-NR609 just now. 3-4 minutes heating with a 50W 240v Halogen Bulb touching the TI Chip. If it doesn't last then I will try 6 minutes. Started to smell a but burnt dusty.

I have TXNR609 which i bought nearly 2 years back From what i can gather i'm the second owner of it from brand new Having watched you vid i thought i would have a look at the famous HDMI board and the DSP chip as you pointed out and i was happy to see a little sticker on top of it saying NEW lol so i'm praying that this means someone once changed it All this means now is one day the HDMI board will probably fail next but seen as this amp has been around now 9 years i just hope it lasts till i can afford a new Dolby Atmos based amp one day lol Great vid

Thank you for your advise. Fixed mine thanks to your advise and knowledge.

You helped a lot with my 709 before I paid Onkyo to fix mine I found that if you put the audio settings to DIRECT you can get the amp to come on in stereo.

@12voltvids

5 жыл бұрын

Not mine. When it failed it was dead even in direct mode.

@spikester

5 жыл бұрын

@@12voltvids I think the dead chip stops the protection relays from closing, so the audio is gone until that happens even in direct mode. I had an SR-707 repaired by Onkyo for free a couple years back that I bought in 2010, it worked fine since before selling it.

@BeefyMon

5 жыл бұрын

My TX-RZ800 died a similar death (I will try this fix shortly), but the analog and toslink inputs still work perfectly (assuming the unit isn’t set in a mode that require the dsp chip to process the sound). Dolby 5.1 works fine, as does All-channel stereo, and so on. I ran my blu-Ray player’s HDMI directly to the TV, and used an optical cable to feed sound to the Onkyo. I lost the higher resolution audio and Atmos support, plus the ability to switch video sources... oh, and the onscreen menu... BUT, it got me by until I picked up a newer model at a decent price. Incidentally, I wasn’t aware of the RZ800 being prone to this issue, but it happened twice (the first time under warranty, the second time, not).

Nice video i just learned something thanks for the great work.

Thank you kind sir. I used a heat gun instead and it literally worked in seconds. Saved me money. I was about to go out and buy a sound bar. Subscribed!!!

@12voltvids

4 жыл бұрын

I didn't have a heat gun handy. My amp is acting up again, will work on it again some day.

@vortexor1

3 жыл бұрын

Does it still work? Thanks and best regards

@doublejay74

3 жыл бұрын

Quick update: My receiver doesn’t initially work on start up so I apply the heat gun for a few seconds and it works. About a minute later, it’ll give out again and then I reheat it again and it stays on for the rest of the time I’m using it. The only downside is the heat gun is literally resting next to the receiver should it give out. I’m just waiting for the day it completely craps out. A new receiver would cost me around $400.00 from what I’ve seen on Amazon. Not bad but I’d rather not go there. Times are tough.

@gryanm

3 жыл бұрын

That's what I was gonna do...but my receiver is only missing one channel out so far. What temp should I use for a heat gun, and for how long?

The same problem was also present in a batch of Denon and Marantz NR series (which presumably use either the same board or the same chip). Onkyo had an extended warranty for their NR receivers because of this problem, and my Marantz was simply RMA'd and fixed under warranty. After replacement of the HDMI/DSP board it worked fine ever since.

This fixed my RT590! Thank you so much! Though we'll see how long it lasts, at least it's working again.

@vortexor1

3 жыл бұрын

Does it still work? Thanks and best regards

@nwstraith

3 жыл бұрын

@@vortexor1 No, the solder broke again. I gave up on it and bought a new receiver

@vortexor1

3 жыл бұрын

@@nwstraith thanks for that information! how long did the fix worked?

@nwstraith

3 жыл бұрын

@@vortexor1 a few days perhaps. Maybe I needed to hit it with the heat gun for longer, but I was getting nervous about cooking the board.

I used a heat gun carefully on the DTS chip, now its working again!! Thank you for the tip, money saved:-)

@vortexor1

3 жыл бұрын

Does it still work? Thanks and best regards

Sent mine into Onkyo years ago, they fixed it.

great video, used a heat gun with nozzle to heat the dsp chip for 1 ½ min. and now sound is working, also the Network actually also work it was not responding before repair. Have added a small heat sink on top of dsp to improve, but thank you very much.

I've worked on this same problem and it is as you say, it is across the board but I don't think changing the DSP chip is going to solve anything. The problem is the extreme amount of technology compressed into that little chip. The chip is like a CPU in a computer, it needs a heatsink attached to it but the problem I've noticed is there is no mounting holes to hold the heatsink to the board, at least on some of the boards. (like the one you are showing us in the video) I've spent a lot of time and work on this problem and I do have proto-type solution in the works. Some of the boards have a thru hole on each corner of the DSP chip and with these holes I've attached a heatsink with a custom made mount to displace the heat generated by the DSP chip. Only time will tell at this point if it works. (fingers crossed)

Hello 12v' i own a TX NR-807, is this temp fix will work for "no video" from hdmi? Sound is ok feom hdmi and rca's works fine also. Thanks

Always enjoyable, cheers

watt is the wattage on that lamp you are using? I need to get one of those. I have been using my hot air rework station for that

@snowyrain5730

2 жыл бұрын

That's a halogen MR (mirrored reflector) bulb and they're usually 30-50 watts... but be careful, they get VERY (VERY!) hot!

Wow, just purchased a Onkyo TX-NR575 for Christmas last years. Had no idea they had these kind of failures. I was in the electronic service business myself started in the mid 80s but by the mid 90s I gave it up. Hard to make money since consumer electronics was getting so cheap. The cost of doing service kept going up, the return kept going down. Also I got was pretty tired of working my arse off only to make the shop owners rich. Got into office equipment after that and did pretty well.

@martinm9979

Жыл бұрын

onkyo did a recall few years back due to this issue . many ppl bitched about no sound video issue so onkyo caved in and did the recall. had my ht rc270 fixed for free. gowever all electronics mwde these days made like crap. cost 150$ these days in canada for diagnosis.

Thank you so much... I had the chip changed about 18 months ago and it just recently started playing up again. This done the job. Incidentally, I also noticed my remote from my phone did not work and this seems to have rectified that problem also! Again, thank you!

@vortexor1

3 жыл бұрын

Does it still work? Thanks and best regards

@davidkettley6685

3 жыл бұрын

@@vortexor1 I got about another 2 months out of it, but finally it died. It is a temporary fix, until you can get it replaced. I just brought a new receiver from Denon as I was absolutely tired to keep wondering if the Onkyo would give up again.

@vortexor1

3 жыл бұрын

@@davidkettley6685 thanks for the information!

@stefaness2153

2 жыл бұрын

@@davidkettley6685 Are you satisfied with the sound of your new Denon? I also bought one after my Onkyo tx-nr509 failed with no sound (since i did not know of this video back then!). But compared to the Onkyo the Denon sounded extremely flat and not voluminous at all (though the setup was the same with 5.0 speakers). I ended up returning it and bought a used tx-nr609 from ebay for about 200€ just a week ago.. the sound characteristic is exactly what i expected the Denon to be and even a bit better than on the 509. The added bass of the Onkyos is just perfect to compensate my lack of a subwoofer. Maybe i can fix the issue on my 509 now with the help of this vid and resell it for a higher price than it being in state "defect".

@davidkettley6685

2 жыл бұрын

@@stefaness2153 the sound is definitely not as rich as the Onkyo, but the reliability is spot on. I tend to find it depends a lot on the source material.

Thank you! It worked for me 🤘 I used hair dryer for couple of minutes.

I have a Onkyo NR616 and an NR818 and they both went back to Onkyo for warranty repair for exactly the same fault! Great video, nice to know what caused the failures, now that my amps are repaired I have a 5V fan sitting above the rear of the amp (powered from the rear USB) to help stop it overheating again.

@aksolartechnologieskriskan6668

2 жыл бұрын

I have the nr616 with no video output

Your "fix" worked on my Onkyo xx-430, thanks!

@12voltvids

4 жыл бұрын

It will for awhile. Mine lasted 2 years.

That’s magic. I didn’t know that you could fix chips with a light bulb. I know that you can fix soldering issues with a bulb or applying heat but not fixing broken chips. Amazing. Thanks for the insight.

@12voltvids

2 жыл бұрын

The fault is bad solder under the chip.

Had same issue, did not believed it would work. Initially it did not, but after that I took the board off, so I can flip it, and did the light thing on the underside over the soldering and VOILA, it is now working! I will put a heat sink on that chip to hopefully have it last longer (I read that the sticker that come with cheap heat sink is not transferring heat correctly, so I will use thermal paste) Thanks for the info.

Our Onkyo 708 and 717 both had bad chips. One repaired under warranty and the other required a replacement DSP board. Two newer models are trouble free so far.

Hi you all, in many cases there are problems with solder connections, especially after the change to lead free products... reheating can be one way to start... and with something as simple as a Halogen lamp...nice video :-)

Also from what I heard from fellow technicians, when Onkyo did the recall till october of 2018 where they fixed those for free, they used a board that dropped the DSP voltage rail from 3,3V down to 3V, most likely to lower the power that the chip needs to burn. Huge fail on behaf of Texas Instruments...

Good tip, will try that on a device I have that has a bad system chip. You could stick a heatsink on it, might stop it recurring as quickly.

@godkast9904

4 жыл бұрын

Good sir, I owe you a beer. I reflowed the chip with a heat gun and stainless steel funnel (works great for BGA parts btw, as you can get them typically in a set of several sizes and they give you precision control of the airflow) and BAM the sound is back. Sure it may not last, but the fact it worked is enough for me to say thanks.

This is all good information thank you guys very much

I glued a heatsink on mine 4 years ago and it is still working.

@saqibsami7967

5 жыл бұрын

Which compound did you use and size of heatsink?

@dom3827

5 жыл бұрын

@@saqibsami7967 i think any heatsink that is not too large will do the job.

@int53185

5 жыл бұрын

@@saqibsami7967 Arctic Silver compound. The heat sink I salvaged from an old tv circuit board roughly the size of the chip.

@CT-te3kb

4 жыл бұрын

@Stephen Morton Needs to be a non conductive thermal compound to adhere the heat sink

@MrTopsoil911

4 жыл бұрын

I used a mix of white toothpaste and dab vaseline. Working now 4yrs

Very useful information! Thank You!!!

Learned something, so thumps up!

Thank you so much for a nice, easy to watch and understand video. My Onkyo HT-R591 clicks like twice (I guess speaker relay?) But it doesn't sound like it clicks the last time. I usually leave it on for a couple hours and it will eventually kick sound on. However now the sound will not come on at all after an entire day of being on. :( It seems like I was inevitably heating up the receiver and eventually it would kick the sound on.

time to give this a go, sadly australia missed out on any opportunity to get theirs repaired as there's no repair places in australia! Thanks for the video, ingenious way of heating the chip too! haha

@12voltvids

4 жыл бұрын

Should work for awhile. Mine lasted 2 years before acting up and is sitting in the corner. Will give it another go some day and see if it will work again. I am using an even older one now for my home theater amp. All i use it for is watching tv. I liked the one that broke because it had very good input switching for all my legacy equipment. Nee ones only have hdmi so I can't connect my old dvd player, laserdisk or vcr.

@JanaBuvari

4 жыл бұрын

@@12voltvids I'll report back with my results! Fingers crossed and thanks again! I enjoyed the video 😁😁

I really enjoy watching your videos, as a complete layman! Maybe you repeat your diagnosis and other comments various times to make sure the message gets across, which is probably very good teaching style. I find it sometimes a bit too much. (You must have said 5 times that these AV-R have problems with the DSP... ;))

@odotb9916

5 жыл бұрын

I love this guys videos, but you're right he does repeat himself a lot!

Thank you that tripped worked wonders of just done it and it seems to have fixed the problem👍👊💥

Is there much difference between cheap AV receivers ? Pioneer vs Yamaha vs Denon vs Onkyo vs. ? Any one any Better quality than the others.?

When I first saw the title,,, I thought it said, " trouble over Tokyo " and I thought, what the heck is Dave doing now lol. Then I read it again and realized I need to clean my glasses. ;p)

@kindanyume

5 жыл бұрын

snds like u r taking lessons from my mom when her glasses were on her head but she was scouring the house trying to find them...

@arthurdanielles4784

3 жыл бұрын

🤣🤣🤣

@arthurdanielles4784

3 жыл бұрын

@@kindanyume 🤣🤣🤣

@kindanyume

3 жыл бұрын

the funniest part is my wife just pulled the same move last night.... lmao

That's why I hate BGA. Dust deposit, self desoldering etc etc Cheers from Indonesia

I have a TX DA747 the receiver turns on and will function fine then a couple days later no sound is my chip starting to fail? TIA Mike

It worked!!! I have a NR626, put a heat gun on it on low for a few minutes. THANK YOU SIR!!

Thanks for the info, mine has been dead for about a year now. Mine started by being intermittent. Now I can try your method and not be out anything because I was considering junking it.

@12voltvids

5 жыл бұрын

I'll put my old one up again and bake the chip a second time and see if it will come back to life again. As I was saying I got 3 years out of mine before it went out again, and because I had another older unit I just swapped it.

I have just purchased this Onkyo amp because I had 2x Sony STR DE475's which have the same issue with relay not clicking for sound so I'm worrying now - anyway my way is to hit it from the LEFT at the precise moment when it CLICKS - sometimes I have to try it 5-6 times but it always worked so far;)

I had the same problem on one of the onkyo thanks for sharing this video

Will this also be able to fix a „no video“ issue? My TX NR 3030 lost all Monitor Outs (Main-Sub-Zone2) over the past weeks. Sound still OK. Onkyo replaced the Board already 2y ago, when only the Sub Monitor Out was without function that time.

Why care about the people who give you thumbs down, they are idiots. The goals is to diagnose the problem and fix it. Just because it is unconventional makes it better and creative.

@therealjammit

5 жыл бұрын

If it's stupid and works, then it's not stupid.

@MichelLinschoten

5 жыл бұрын

Sure .....just hack away duct tape can patch tons of stuff ....doesn't fix it.

@ThatTransistorGuy

4 жыл бұрын

I gave a thumbs down simply because they said "onkyo garbage receiver" if it was a simple diagnose and repair, then why put that???

@jeffcotton526

4 жыл бұрын

I gave a thumb down too because of his blanket statement about "Onkyo garbage receiver". The chip was/is garbage not the receiver. He continually makes generalizing statements about overall product quality in a lot of his videos. He should have clarified by stating: "junk Texas Instruments chip." Onkyo makes some excellent top-notch products, I used them for many years. ALL BRANDS at one time or another suffer from poor or bad component quality, whether it's Marantz, Acoustic Research... whatever.

I have recently came across a Dual 1249 turntable. It looks like someone got it overseas and tried to rewire it for US voltage and failed. Do you happen to have a video or photos of how the motor, power block and switching block are to be wired? I found a service manual that has the schematic, but the wire colors and some components are different and I just want to make sure I have it right. I think both of those blocks are the same on all 1200 series turntables, I just don't have another one to compare it to. Thanks!

Sad to see that these newer Onkyo receivers are apparently not reliable. They used to be a pretty big player when it comes to stereo amps. I have a A-9155 that I have not turned off in over 5 years and it still works fine.

@andrewstambaugh240

10 ай бұрын

It was a common fault of the era, drive by government regulation forcing too rapid a transition to under-tested new solder. A whole bunch of computer parts had the same problem. Laptop gpu's were notorious due to running hot and exposing the flaw in as little as _1or2 years!_ imagine buying a new laptop and bluescreening with HW failure in less than 2 years. Also, note that the fault use in a TI chip, not onkyo. Several other companies had similar problems, but onkyo had more *because they put the best of the best new chips available in even their cheaper units.* Most other companies were cheaping out on features in sub-$800 units, so most of those weren't affected. Things like dolby only or dts only models vs onkyo with both and vertical sound and auto tuning mic and more hdmi inputs and... It's sad the heaps of laptops and other electronic went to the landfill so the gov could put on the image of "saving the environment."

I have an Onkyo TX-NR777 the left Front speaker just gave up the ghost. I confirmed it is not the speaker itself as it works on another device. The subwoofer as well as stoped working. Both issues remained after a factory reset and a firmware update. Thoughts ie should I get it fixed or just look for a new device altogether?

I have an Onkyo HT-RC430 that has a sound issue, but I am not sure if it is the DSP chip or something else. Could use some advise on what to check. I hear two relays click. One when I first power on the receiver and a couple seconds after another relay clicks. Sometimes I do get a bit of sound after the second relay clicks, but not always and when I do get some sound, is not clear and is crackly. If I try to increase the volume the sound will just cut out and will not come back. I have to turn the power off and back on, but the sound does not always come back. I may have to do this a couple times before the sound returns, but it is always crackly. Possibly something overheating????

I used a heat gun for fix and helped at least for time being. So thnx a lot!! TI has a new version of chip available, but selling only to "certified" customers? I.e. to companies who are their service partners?

thank you for great video. how many watt of this lamp?

I just bought one that only makes sound in "direct" mode. Is that because I'm using analog inputs or is the dsp board bad?

I have an Onkyo TS DX 484 and the AM works, The turner works but i don't get anything from the FM..could it be in need of a better antenna? I have a wire on i t and it get s AM just great.

Interesting to note that they started = Osaka Denki Onkyo K.K in 1946. Immediately post WW2.Over the decades they've specialized in AV systems and some amp units? Ah I love IC systems 😆and have watched a few hot air removals (NOT Onkyo) sometimes the solder removed and re 'tinned' before replacing the IC and the unit works fine after which kind of proves how wonderful and let's remember this, a machine installs those ICs not a human being - a machine! Basically heat and flash soldering in one which inevitably ends up with some having weak or poor terminal conductivity. Onkyo definitely not the only ones re this issue. Hmm where did I put my apple...😃Great vid as always and an excellent fix if it works and if you have one of these you've acquired from a thrift or charity shop et IF it works even for a few years after? 😃 where did I put my peanuts.. 😁

I have an Onkyo tx sr506 amplifier that had a defect in the rear left channel. I repaired the defect but I did not find in the service book the table with the voltage values ​​on the measurement terminals for adjusting the idle current. Do you know the corresponding voltage values ​​for all channels for do current readjustment for all channels?

Thank you so much! 2minutes with a hair dryer on my tx-nr609

@JaniLintu

3 жыл бұрын

2 minutes on a hair dryer fixed my TX-SR608 just now.

@vortexor1

3 жыл бұрын

@@JaniLintu is your fix still working? thank you and best regards

@JaniLintu

3 жыл бұрын

@@vortexor1 yes, although it is possible I did it in vain and the real reason I didn't get sound out of it is because I had headset adapter jack plugged in without a headset. :D

I was skeptical, but I’m not lying, this totally worked.. baked the crap out of it and now it works again!

@vortexor1

3 жыл бұрын

Does it still work? Thanks and best regards

@johntranquilli2243

3 жыл бұрын

@@vortexor1 , yup, don't want to jinx it, but going on a few months now!

Started having issues with my HT-390 and then the sound stopped...No other video I found did anything to help.....this worked...Used a 1500W heat gun for about 3 minutes...let it cool for a minute and viola, I had HDMI ARC sound again....Thanks for the post...

@inconspicuous-nobody

Жыл бұрын

Can I ask how long yours survived after the fix? :)

@calvinpoppen665

Жыл бұрын

@@inconspicuous-nobody it lasts about 3-4 months...I had to recently use the heat gun again...Kind of a pain, but cheaper than buying a new receiver.

@inconspicuous-nobody

Жыл бұрын

@@calvinpoppen665 Much appreciated!

Thanks for the video. A coaxial tv box connected to a hdmi in killed my hdmi board because a lightning. Do you know how to check it and fix it?. Thanks in advance.

It works for me. I used an heatgun at maximum power for a minute on the DSP chip on my Onkyo TX-SR313. Thank you for the tip.

I have a Tx-SR313 Av receiver, It has a really long delay when initially turning it on. Can take up to 15 - 20 min before it finally comes on, once it is on no problems works great, Is this a symptom of the dsp failure ?

Thank you so much for that video. I did it exactly as you suggested and it works again👍👍👍

Do you have an opinion on Yamaha receivers? I was after Sony STR-DN1080 receiver after reading its (quite impressive) specs, but they wouldn't sell them officially in my country and black market prices are far too high (and no warranty). So I went for Yamaha RX-V685. I don't know whose DSP chip it uses, papers state that is has four Burr-Brown DACs (which are good, right?) I am satisfied with it as of now, especially because it has 'Pure Direct' mode which promises no processing of incoming signal.

Thank you for the video. I used the hair dryer instead of lamp, and also made it.

I have a onkyo HT-R580 from 2010 - with rca inputs (analog) in aux port - i can get sound if i change mode to "stereo - all speakers" but not in normal stereo mode...does that sound likely to be dsp issue? i hear relay click when i put in stereo-all speakers mode...

Do you know if this also affects the Onkyo CS-265 shelf system?

Hello! I have an Onkyo TX-SR313 and it was a great receiver for me for years -- but not quite as long as I wanted it to be! -- and it inexplicably stopped working. I thought the problem was originally the speakers, but now I'm more convinced than ever it's this chip issue. I'm gonna give this a go and see what happens. What the hell!

You are my hero! Did this yesterday on my Onkyo TX-8050 and it works again! The only problem was to get a 50watts halogen-bulb because (in Germany) it‘s not allowed to sell it anymore regarding energy efficiency, so there are only led- lights left. But at least I found one in the internet. Really fantastic! I will now just put a heatsink on the chip and maybe install a little cooling fan to prevent the chip getting too hot in the future. Thank you!!

@0rigpumu

2 жыл бұрын

How long do you have the 50w halogen lamp switched on to heat the chip?

@markusk.7621

2 жыл бұрын

I had it burning for 7 minutes and then took it off so that the chip was able to cool down.

@markusk.7621

2 жыл бұрын

7 Minuten, dann runternehmen. Ich hatte zur Sicherheit eine Alufolie über die Platine gelegt, in die ich ein Loch gemacht habe, sodass nur der Chip mit der Lampe in Berührung kam.

@0rigpumu

2 жыл бұрын

@@markusk.7621 Ich werde das mit meinem Pioneer sc lx86 auch probieren. Der hat genau die gleichen Symptome und ich hoffe sehr, dass es klappt. Anschließend kommt ein Kühlkörper auf den Chip. Pioneer kann keine Ersatzteile mehr liefern. Also Platine austauschen klappt nicht.

@markusk.7621

2 жыл бұрын

Wünsche Dir dass es klappt! Für mein Modell gibt es auch keine Ersatzteile mehr. Ich hab bei mir auch einen kleinen Raspberry- Kühler draufgemacht und dann zusätzlich noch einen 80mm Noctua- Lüfter mit low-noise Adapter eingebaut, der die Luft von dort weg aus dem Gehäuse zieht.

I have an Onkyo M-504 that has a long lag before the servo relay clicks on. Any thoughts? Once it clicks on it runs fine.

Thank you for this video! I have a Onkyo that is doing the same and I will try this out.

Also note this is one of the reasons I am 1000% in favour of pre/control amps and seperate power amps! Not only is thermal management easier but even if the pre never had a failure when it comes time to upgrade etc it could help save $$$$ since onlt the pre would need replacement In my own case I have a very nice Denon 4300 butand I can build another custom power amp (multichannel) to use with the Denons pre-outs though my unit dooes have very good onboard non-IC based power section (umlike cheaper units like my old kenwood) I do wish the mfrs would offer the dsp/pre seperately from power amps or at the least build in an "off" setting to 100% tuen off thw power for onboard power. That and i they wont spend the few cents for added heatssinks as OEM allow the consumer to do such w/o voiding any warranty etc

@shuhradk

Жыл бұрын

Would you mind sharing some of the pre-amp and power amps combos you have used?

@kindanyume

Жыл бұрын

@@shuhradk no s Dont mind but other than a few peesonal pieces i havnt worked with such the same as i did yrs ago That said when i worked with many goodies 99% of with i couldnt afford i was lucky to get exp with everything from old school technics/pioneer/denon/yamaha to carver to rotel bryson and many others. As for personal i want to find a nice carver 27 or similar to replace my temp carver.. with is in place of my very old kenwood with is replacement for a cydtom hand built unit that some scum stole from my yrs ago Add to that a 400t of i can find one i can afford (and mod to mkii) to go with my 55x for 2ch+ use of mixed with my 505.. of my denon 11.1 ch proc reciever For HT use

I have an TX-NR609 with an already warranty-replaced DSP chip. I recently lost my sound, but I still get the speaker indicators on the front of the unit. Do you think it's still worth trying to reflow the DSP?

I am get a popping noise when turning onkyo TX-NR515 on and off. Does anyone know what it maybe? Note: if I lower volume all the way before turning it off it will not pop only when volume on.