VERY informative! One thing you might want to try if you're not getting water out onto the floor is to turn the machine off then press the trigger for 30 seconds. You might have lost prime to the pump itself. Happens a LOT especially if you don't use it that much. AND if that fails to get it to work, take the clear plastic cover off that fits over the rollers, flip it over and you see a series of small plastic 'nipples' with a small hole in each. THATS where the water comes out to the rollers. They DO get plugged. Use a straight pin or a needle to clean out. That'll happen if you put it away 'dirty'. If you see black, they're plugged and water won't get to the rollers.

@monroevac

Жыл бұрын

Thanks for sharing this tip

@anncaulder8123

10 ай бұрын

Don't return the water back to the return water bottle

@bearcat8817

10 ай бұрын

Thank you, was in a hurry ❤

@ellenjagger425

4 күн бұрын

Thanks so much, saved the day. Also, I have lost suction suddenly if I accidentally knock the hose attachment flap open while cleaning under something close to the ground.

@monroevac

3 күн бұрын

@ellenjagger425 glad to help

If you have my issue, no need for disassembly. So there is a clear piece of plastic between the beaters. It allows the water to soak the carpet. It has very fine holes that need to be unclogged with a needle. If you’ve used it before and let it sit, the holes will/can be clogged. That was my issue. Water worked fine out of the handheld hose dispenser, which led me to flip it over and find that clear plastic bar between the beaters. You will notice the holes will be black or brown and they should be clear. Grab a needle and some compressed air. Done.

@Wagimomo

Жыл бұрын

do you have picture of it ?

@gregoryhausinger9072

Жыл бұрын

Yeah I had same issue, no water would go onto the floor. After partially deconstructing the unit and determining that water was going down to base of unit, I took a closer look at the piece with the 2 green thumb buttons. I was fortunate enough to have a 5/8ths clear hose that fit perfectly over the the feed area that has 2 little black washers. I held on tight (the 2nd time..I was wet :( ) and the warm water started blasting through the row of holes 1st one..then 3 and so on. I hit it with a cheapo paint brush and got them all working. This will be part of the routine every time I use this thing now.

@MaraDroiiD

Жыл бұрын

Can you add a photo of the holes you are sharing to clean out with a needle? I have no water spray to the floor. Water for the hand tool and the foot press power shot button on the right base of the machine works fine.

@markcasey6169

Жыл бұрын

@@MaraDroiiD they are literally in the clear hood down where the water comes out. turn over the vacuum and look at the clear hood that covers the beater. there are holes in the entire length of it. those were clogged and a needle in each one opened the pathway for water to flow out.

@Bulldogandtea

10 ай бұрын

Thank you thank you thank you - this was my problem. Your advice stopped me from throwing my machine out of the window in frustration! 2 mins with a needle and all was fixed 🤩👍👍👍👍👍

Thank you a lot, you helped me understand how does this cleaner work and that made me able to fix the issue I was having with it

Nice work. Holy cow these machines are like effing lemons. Multiple models with the same extremely common problem. Tons of people having the same issue doesn't mean the customers are idiots, it means Bissell engineered a poor product. If there's a tendency for something to clog, those areas should be user serviceable for proper cleaning and it should be documented in the manual so we don't have to go complaining about it. Good grief.

Been wondering where seal has been 🤷🏻‍♀️ thank you for your help GOD BLESS ALWAYS

Wow!! Amazing art!! You are so gifted! Thanks for the video, I'm still trying to get this figured out.

@monroevac

Жыл бұрын

Thank you

Beautiful artwork! Love the Hendrix colors. Thanks for the video.

@monroevac

Жыл бұрын

Thank you

Great video. Very clear video and good explanations. Thank you!

Thank you! This helped me get my Bissell back up and running!

@monroevac

Жыл бұрын

Awesome

Love your attitude. Keep up the troubleshooting videos. 😊👍

@monroevac

2 жыл бұрын

Thank you. Will do

Thank you very much for great videos, especially Bissell Pro Heat 2x. Awesome art work….keep up all the good work.

@monroevac

2 жыл бұрын

You’re welcome

Great artwork and thanks again for these videos.

Thank you- thank you! Sooo helpful! Especially to see how you have to arm wrestle those silver plastic plates and try not to break.

@monroevac

Жыл бұрын

You’re welcome

Thank you! Your awesome. Saying " its easy " alot helps...

@monroevac

2 жыл бұрын

You’re awesome for leaving an awesome comment😄 I’m glad it helped you 👍🏽

This helped me out with my machine sooo much! Saved me so much stress! Thank you thank you thank you!!!!

@monroevac

2 жыл бұрын

You are welcome

The bottom nozzle of the water jug can get bent and misaligned so it won't seat into the receptacle correctly. The "heatwave" function softens the plastic so when you take it off to fill it, you have to be careful not to bend it.

What a Cool Shop Mr. Monroe!! The Jimi Skateboard had my eye all the time. Oh yeah and the tutorial was an eye opener. "It's a Revo-lu-tion!!!!

Great video! Got my Bissell fixed! Thank you!!!

@monroevac

Жыл бұрын

You’re welcome

Great video! Thank you so much for sharing your expertise.

@monroevac

Жыл бұрын

You’re welcome thanks for watching

Thank you for this. It helped a lot.

@monroevac

2 жыл бұрын

You’re welcome. glad it helped

wayne, thanks for your direction, and you made my life easier. Im a mechanical engineer and just completed Resorts World in Vegas . it was easier building the casino than the shampoo Machine. Thanks 😂

@monroevac

8 ай бұрын

Wow. Thanks you for that compliment 😊 glad to help

Thank you so much for the detailed instructions my attachment is finally working

@monroevac

5 ай бұрын

You're welcome!

Thank you so much for doing this!

@monroevac

2 жыл бұрын

You are welcome 🙏

Thank you! Great video

@monroevac

2 жыл бұрын

You’re welcome John

Really helpful. Thank you.

@monroevac

2 жыл бұрын

You are welcome

Thanks Brother, great information

Wonderful video and you are such a talented artist!

@monroevac

4 ай бұрын

Thank you 🙏

You sir are a legend.

@monroevac

Жыл бұрын

Thanks

Thanks for the guidance!

@monroevac

Жыл бұрын

👍🏽

Thank you sir! Very helpful video!

@monroevac

Жыл бұрын

Glad it helped you 😀

Thank You!! This video helped me fix my machine.

@monroevac

5 ай бұрын

You’re welcome

Hi Wayne I was finally able to get through to Bissell on Wednesday which wasn't easy about my Revolution pet 2 motor was smoking and grinding so I'll be receiving a new one tomorrow quite remarkable another company that is good is Greenworks they too sent a replacement power washer after some phone troubleshooting ...had a problem with the electrical plug ciao!

@monroevac

2 жыл бұрын

Awesome 👏 I’m glad it worked out

I tried to follow this video but I couldn’t get the hose off and water was slowly coming out on the main hose at the end but I put it back together tried it. No luck took it apart again and then noticed one of the hose clamps was caught on the fitting and I fixed that put it back together and now it works like a dream

THANK YOU for showing how to disassemble all the parts! I got as far as testing for water flow. I do have water flow and I do have it set to MAX clean, but the water flow is very light and inconsistent. Any tips on what to check from there?

Thank you so much for this video! Is there anyway you could make a video on how to change the lower/foot hose on the Bissell Revolution? It seems like such an easy fix but shew 😭. Thanks for being awesome!

Great info!!! Also. amazing art sir!! :) Thank you!

@monroevac

4 ай бұрын

Thanks and you’re welcome 😊

Great job!

@monroevac

6 ай бұрын

Thanks

Sick board! 😊

@monroevac

2 жыл бұрын

Thanks! 😁

Awesome board

@monroevac

3 жыл бұрын

Thanks. Working on a commissioned piece right now. Having fun 🤩

Omgosh! Thank you so much! Liked and subscribed! But mine still doesn't let out water. T_T Edit: For some reasons, my spray nozzles for the bottom was clogged. It created this air gap between the black tube and the nozzle path which didn't let water flow. After cleaning it out, the water flows now, but... I think the pump itself is also weak too, so I'll probably need to replace it. I don't think the system was design to rely on the pumps but use gravity.

@monroevac

2 жыл бұрын

Yes. The pump is for the hose. You did great

Did everything in the videos for Bissell proheat model 9300 -heater not bad but cleaned up and checked inlets and outlets, cleaned sprayer they were also ok took line off solenoid which did nothing - only thing I see is that the forward hose out of the heater is filled with foam after I try it -any suggestions - Thanks

tytytyty for the video. much love...xx

@monroevac

Жыл бұрын

You’re welcome ☺️

This video didn't necessarily solve my problem but helped me from losing my mind until I figured out why mine wasn't working haha. I will keep all this in mind Incase I need it in the future. FYI mine was caused from the top part of the foot, inside of it the row of little nozzles were clogged I used a needle and boom working.

@monroevac

5 ай бұрын

Happy to hear that you solved it, 😁

Thank you so much

@monroevac

2 жыл бұрын

You’re welcome

Nice, but the water flows just by pulling the tigger even when you dont have the unit plugged in and turned on. What I have is a trickle of water when using the upright power head and a strong spray of water when using the hose attacfhment. Is it the same motor feeding both final sprayers? All lines are clear of impediments, blown out with compressed air - just no spray on the brushes.

you tube does it again, thanks for posting, my lower suction hose came of its fitting, poor poor design by Bissell, when you place unit in upright locked position its pulls on the lower suction hose so much that it pulls out of its hose fitting socket, stupid design. even though you didnt touch base on my specific problem your video helped me take it apart to fixt my problem, Im sure it wull pull out again eventually, so I have to be careful not to place in locked upright position I guess.

@monroevac

Жыл бұрын

Glad you found the source of the problem. Thanks for sharing

How would I take the whole stick handle off. I pull the trigger and get resistance but I hear squeeking near where the neck of the handle meets the clean water tank. My problem is that I'm not getting water coming out of the bottom. Sometimes it trickles out but I have to pull the trigger multiple times. I'm gunna try and take it apart as you did in the video and check anything that seems out of place. Let ya know how it goes!

Thank you for all your very Helpful tips shared in so many videos! Would you be able share how to replace the red rubber seal for the water tank?? Been searching for a how to video but not finding one. Somehow mine got messed up & is not dispensing water (unless i press down on the tank, to help it "seat" properly). I have this model you're sharing about in this video, Bissel proheat 2x revolution pet pro.

@monroevac

2 жыл бұрын

Will do, stay tuned

@tessaw55

2 жыл бұрын

@@monroevac Ooh Thank You sir 😁!! You are a blessing to so many! Seems it should be easy. But (often) taking pieces off or apart (on various objects) is easy but get pieces put back into place is not always as easy (for me anyways).

Hi Thanks so much for the video. It helped me to follow the steps to check the washer not spraying water. Unfortunately the steps did not solve the problem. I want help where to get pump and how much it cost. You did recommend to buy the white tank and the motor.

@monroevac

Жыл бұрын

Glad it helped

Hi , Where can I get a new motor for the brushes? Mine only works if it tap on it?it’s a model 9400-T 11270C

nice job

@monroevac

Жыл бұрын

Thanks!

Many thanks - very helpful video. I'm considering the Revolution Pet, Revolution Pet Pro, or Bissell's newer TurboClean DualPro. The TurboClean looks to be larger version of the smaller TurboClean PowerBrush that I've had great experience with. Would you recommend the TurboClean over the Revolution models? It looks to be simpler design (no Heatwave), might last longer?

@monroevac

2 жыл бұрын

I recommend the Bissell Revolution

My vacuum stopped squirting the water out. Long story short. I ruined the water tank by adding boiling water to it and something happened to the bottom of it. All I did was swapped out the water tank $40 on Amazon and it worked like new again.

@monroevac

Жыл бұрын

He p boiling water would do! Glad it worked out for you

@joerollerblade

Жыл бұрын

Thanks for your insight about the boiling water. I too had used boiling water and subsequently experienced a permanent loss of water flow. However, I was able to easily fix the problem without buying a new water tank (see below). I was suspicious boing water was the culprit, but could not image by what mechanism it would cause damage. Sure enough, tipped off by your comment, examination of the tank revealed that the nipple region (that houses the lower valve) was obviously bent out of alignment, such that it was no longer able to engage with the receiving port in the base of the cradle. Luckily, the nipple itself (the 3/4" cylindrical portion) was seemingly undistorted, given that the valve operated just fine (no leaks). TO FIX IT, I simply filled a portion of the tank with boiling water, and (wearing leather gloves) I grabbed the nipple between forefinger and thumb, and (with very little force) was able to tweak it back into alignment. "Alignment" was basically an eyeball determination that the nipple was once more parallel to the axis (direction) of insertion. I'm sure somewhere in the manual it says DON'T USE BOILING WATER! My guess, however, is that even overly hot water (not necessarily boiling) could cause this distortion - especially if you fill it, as I did, with the tank resting on a surface, such that the nipple (in contact with the surface) is forced to bear the weight of the water. It's best to hold the tank by the handle while filling.

Nice painting

@monroevac

7 ай бұрын

Thanks

First I would like to say thank you, thank you so much for teaching me how to troubleshoot my Bissell ProHeat 2x Revolution Pet Pro Carpet Cleaner. Thanks to you, I might have an idea as to why water is not coming out of the Main hose line (as demonstrated toward the end of this video) . I checked all three ways of putting out water (Main motorhead, hose, and spotter); no water comes out. I checked in all 3 settings (Express, Deep, and Max Clean); no change. I checked the trigger, which still has resistance. And I checked the gasket on the water tank. I do not know how I can check, let alone fix the auto-feeder that receives the water from the clean reservoir tank. I'm sure you're a very busy man, and may not have time to reply to this. But Do you by chance know what I can do PLEASE.

@monroevac

Жыл бұрын

Hmmm-2 options- change your belt (pump belt) if that doesn’t work then opt to change your pump

Thank you for the video. Motor is running but the brush drive axle (whatever part this is at 11 minute mark) is a bit rusty and doesn't turn. It has burnt thru two belts already, do you have any tips to fix?

@monroevac

Жыл бұрын

Need help finding the right video- the video thread you are commenting on only runs for 9:26 minutes- try copying and pasting the link

Do you have a solution for the clean shot that will not stop spraying? It’s brand new. I hate to exchange it because this is my second one. I exchanged the first one because it dripped too much.

@monroevac

2 жыл бұрын

Just uploaded a video covering that. Check my Bissell tips playlist

@paulan.4409

2 жыл бұрын

I bought one and it worked perfect the 1st use. Second use water did not spray out of the handle nozzle so I returned it and ordered the same one. Again first use and it worked great! Tried using it again and no water comes out and the bottom shooter would not stop spraying. Trying not to return it again but want to fix it once not take it apart after each use. Thank you for your great video now I will have to take it apart again. I thoroughly cleaned it and that was not the problem so I'll have to try again.

Ok did all that. Seems to get water through just fine. Even checked that last part where you said could be clogged and that's spraying water too. Nothing comes out though when I put the machine back together. And the clear tray on top isn't clogged. I'm at a loss

@monroevac

2 жыл бұрын

Next step would be to replace the pump

@ryanshock2541

Жыл бұрын

Fuck I’m in the same spot

@lilydilly86

Жыл бұрын

@@ryanshock2541 make sure no one messed with the setting on the side🤣🤣🤣 apparently my problem was someone put it on light cleaning instead of max!

Sweet deck!! Now to tear apart my cleaner...

@monroevac

7 ай бұрын

Thanks! good luck

This is great. Is there a video for if water isn’t coming out of the connection? I separated the hose like you said and no water is coming out. I even sucked on it. Is there a part two?

@monroevac

8 ай бұрын

Try checking your pump belt- if it’s stillborn spraying after replacing the pump belt then maybe it’s time to replace the pump

Very well done on troubleshooting. Although I have the Bissel Deep Clean Professional Pet shampooer and the brush motor works for a small time and then stops. Removed, cleaned brushes nothing binding them and they move freely. Any suggestions? motor, switch, etc??? thx

@monroevac

2 ай бұрын

sorry for the delay-It may be the micro switch (I believe the deep clean pro uses a micro switch, located near the back wheel) otherbthan that check fpr broken or ripped wiring

@gefflynn7171

2 ай бұрын

@@monroevac Will do! Thank you so much.

Hi, just wondering the troubleshoot if trigger is working correctly but water not coming out of hose when unit is on and trigger is pulled? Any help would be greatly appreciated

@monroevac

Жыл бұрын

Consider tank- if the carpet section is working then it’s not the tank. Possibly the hose

Omg I want to marry you 😂 a video that saved me, made sense & explained TECHNICALLY what’s wrong with my machine that I desperately need to use but have found no water to be coming out of 😅✌🏼 you ROCK!

@monroevac

2 жыл бұрын

You ROCK lLola, I’m glad it helped you.

@NerdyGirl760

2 жыл бұрын

Noooo I want too!!! He saved my day!!!

@CharlesAAnnen-rh4mk

2 жыл бұрын

Is there not a pump involved

@mindyloper4454

Жыл бұрын

@BFaith while I was watching the video your comment was the only one I could see until I clicked on it & THENNNNNN 😂😂I thought 😮 OMGEE! I MUST AGREE 😂😂🎉🎉🎉 BRAVO TO THIS AWESOMELY EXPLAINED DETAILED VIDEO.... EVERY OTHER 1 I COULD FIND WHICH WASN'T VERY MANY JUST WANTS TO TALK ABT THE TOP BUT NOT THE MIDDLE 😮😅😂🎉 MINE STILL SPRAYS BUT YOU CAN TELL IT'S CLOGGED a little SOMEWHERE PROB Bc OF OUR SANDY WATER IN WEST TEXAS!!! YOU ROCKED THAT VIDEO SIR!!!

@gracecatz3996

Жыл бұрын

Definitely

I was able to correct my clean shot issue with this model your working on here. Thank you! Now I began to wash my carpet and discovered the rollers aren’t functioning properly. Moving forward or backwards? I checked both belts and neither are broke. I’m having issue placing the larger belt as another person indicates a red pulley. There isn’t any such part. Please help! My dogs are driving me crazy, they are aging (as we all are) but accident seem to happen more frequently. MaryLou

@monroevac

Жыл бұрын

Sorry for the delay, just saw this comment. Ok… the clean shot is part of the basic Bissell 2x models and they don’t use the pump beltZ the use 2 geared belts. A smaller belt from the brush motor to the 1st brush and the larger belt to connect the 2 brushes. This larger belt is on the opposite side. Inspect both sides of the brush roll

@marylouiseshimkus7221

Жыл бұрын

@@monroevac I discovered both belts. Could not get the larger on to remain on the brush roller. What am I doing wrong? Something so simple is so hard? Thank you do much for responding. I’m sure you are a busy man.

Hi.. thanks for the detailed video.. I have a question.. when I was starting to put it back together, I noticed light weight rectangle gasket on my counter near the cleaner. It has rounded edges and is about 2” x 1”. is it from the cleaner or do you think it was from something else that was on my counter?

@monroevac

7 ай бұрын

Check the red gasket below the dirty water tank. There should be a gasket surrounding it

@tamschott1987

7 ай бұрын

thank you:)

Been working in a vacuum repair shop for 5 months and this is the best and most helpful video I've seen yet. And I am a massive Hendrix fan. Your artwork is incredible. BTW-My name is Kurt, not Roger. He's the owner. :)

@monroevac

2 жыл бұрын

Awesome Roger….let me know if I can help with any repairs you’re stuck on.

I need to replace the power cord (dog chewed it) on my Bissel ProHeat 2x. Any tips on how to get to the cord?

@monroevac

2 жыл бұрын

Yes…tune in this weekend.. I’ll have a new video up for you

Hello! great video:) Quick question, I was just about to clean my daughters room and noticed that the 2 bristle rolls aren’t spinning. Is this fixable?

@monroevac

Жыл бұрын

Yes it’s fixable probably a belt. Scroll through my Bissell tips playlist and you should find a video about changing the belt. Your unit has three belts a pump belt and 2 geared belts for the brush. I would start with the pump belt

Mine is spraying from the bottom but not the hose I watched your other video and did the steps checking the button it is all pressing fine but no water from hose, quick shot and bottom shoots water just not either hose attachment. Any suggestions also machine is new out of box

@ohaikittykatt3438

3 жыл бұрын

Also I have a proheat 2x water tank seem to be seated properly, everything clicks into place,water comes out when I put a ballpoint pin head to the congestion area and the machine really works fine otherwise but no hose spray. The suction of both is good, can you break down the water flow from reservoir to pump to hose?

@monroevac

3 жыл бұрын

Sorry for the late response. It’s easier to troubleshoot when you have an extra hose. This way we can eliminate the hose as the problem. Assuming the hose is ok, the only thing I can say without the machine in front of me is to check to the solution flow is on max and clean out the post the the water flows from, next try running the unit and lift the hose lid then use a pen or screwdriver and lightly press the hole to see if water flows out. If not then that connection may need replacing. If it flows then replace the hose

@ohaikittykatt3438

3 жыл бұрын

@@monroevac thank you so much I will order a new hose! It didn’t work straight out of the box.

If water is coming out with/without plugged in, check water tank first. If not the problem, check water shutoff valve located at the bottom of handle. I replaced mine it was stuck in open position.

I have the same but different model. It is black and orange. And I took it apart to clean the brushes and I was trying to get the entire front plastic off and now I messed up the wand hose. So when I put it back together it's draining my water. How do I take off the whole plastic??

@monroevac

2 жыл бұрын

Watch this video it should show how to take the unit apart - search my Bissell tips playlist for “My Bissell Revolution pet pro cleanshot is stuck

Great video! My trigger is only dispensing soap when I move backwards? It used to be both ways. What could it be?

@monroevac

2 жыл бұрын

Hmm. It could be in your handle. Imagine the trigger applying more force when you are pushing the machine forward and less when you pull the handle backwards. Check to see if your handle is secure and check to see any cracks in the trigger resistant

@hinachow1

2 жыл бұрын

@@monroevac Thank you so much! Yesterday, I followed the video and took the handle off. It's in great working order. I will for cracks! It use to distribute forward and backwards. I will let you know what I find?!

Any ideas? I have checked the power cord and even replaced the plug and it does the same thing. Powers on for a few minutes then off again.

@monroevac

Жыл бұрын

Sound like a motor issue- the revolution is a simple set up No pcb boards- just switch cord and motor. Many units would auto shut off if they started overheating. Try running it without the dirty water tank and make sure no debris is blocking the suction port/ filter- if it shuts off again then you may need to replace the motor

Hi, great video. I had a problem with the water not feeding through the brush chamber. One of the two black o-rings had become worn and was not creating a proper seal. Do you happen to know what size those o-rings are? Bissell sent me a new brush chamber, but I can't seem to find the o-ring size listed anywhere, and it is probably a reasonably common problem. Thanks.

@monroevac

Жыл бұрын

Hmmm. I’m not sure about by he size right now- (Bissell Revolution?) I’ll check on it

@randymcsmash

Жыл бұрын

@@monroevac yes a proheat revolution 2x pet pro. Thanks 👍

I fixed mine by sticking a safety pin in each hole of the spray bar underneath the rollers to unclog it.

@monroevac

2 жыл бұрын

Nice work. Thanks for sharing

I changed the belts on my pro heat but it's still not turning the wheel

I have the Bissell pro heat 2x Revolution, and it leaks water out of the bottom. I put the water tank on and the plunger is pushed up releasing water straight down to the carpet. Off or on it leaks. It was fine 2 days ago and now everything leaks straight out. Not sure if its the trigger malfunctioning. Or something else. Any ideas.

@monroevac

2 жыл бұрын

The process used to find the source of the leak is a bit lengthy, but could possibly be resolved quickly. You may have to first take the lower housing off to see if you can spot a leak in the tubing. If you don’t find any leaks, then your problem may be right below the auto receiver. Either the seal is broken or the tube connected to the auto receiver is separated or punctured

@daltonhatton7535

2 жыл бұрын

@@monroevac okay thank you, will look into it. It just baffled me, was fine holding solution one day. The next day ( hadn't been used ) was just completely empty. Only thing I could think is if a kid played with the trigger to much and potentially jammed it.

@monroevac

2 жыл бұрын

Start by taking the handle off. This will help to eliminate the trigger as the source of the problem

My vacuum water did go through the hose and come out from the bottom but when i cover with the top cover, water just not spraying out. any clue?

@monroevac

Жыл бұрын

You may have to replace the pump- the water for the floor and the hose attachment travel a different path after a certain point. If you know of someone with the same unit, try borrowing their window nozzle for this test. If it sprays then I your nozzle may be clogged. If it doesn’t then I recommend replacing the pump.

OK, so my problem with this unit is that when I turn it on, water bubbles a LOT out of the little hole on the unit where you plug in the attachment tool. I can't find out what the part is called or how to replace it. There was a broken little red rubber-band looking thing inside of it and I assume that's the issue. What is that part called and how to replace it? Even trying to plug in the attachment tool to use that, water still comes out at that connection.

@monroevac

2 жыл бұрын

If you take a look at a picture of the Revolution hose, you’ll see the red rubber seal. It belong on the hose. Google an image of the hose. Try pulling the red seal out of the hole and put it back on the hose. It may fix the problem

FYI there’s a switch on the side that limits the water flow depending on what your cleaning. I thought I had something blocking the hose however I had the switch in the cleaning mode which allows the least amount of water.

@monroevac

2 жыл бұрын

that will do it. Glad you solved the issue

@GilaMonster971

Жыл бұрын

Mine was jammed in between the two settings. So no water was passing through. Tore the whole machine apart just to find out the switch was stuck. I unstuck it and it worked fine.

I have no water coming out once you said unhook the main water line… it doesn’t spray out. Do I need to replace that hose?

@monroevac

Жыл бұрын

Check your pump belt

@monroevac

Жыл бұрын

Check out some of my other Bissell videos, you make find the answer there. “Bissell Tips” Playlist

Hi have you done a video on this bissell Carpet cleaner. My motor went out any tips how to change it. I don’t want to buy a new machine I replace my parts when needed. Please thanks

@monroevac

Жыл бұрын

Hi I have a video on replacing the Bissell 2x motor in my playlist “ Bissell Tips” click the bell because I’m working on a Bissell Revolution motor video

@reginamiranda5852

Жыл бұрын

@@monroevac awesome thanks your a life saver. Can you put where to buy the motor at too please thanks your the best

I have the opposite problem. The water doesn't shut off. There is resistance in the spray lever but the water just dumps out of the reservoir. How do you take it apart to get to the area where the problem is?

@monroevac

4 ай бұрын

Take a look at my Bissell playlist. It may have the solution to your problem. BISSELL TIPS kzread.info/head/PLdsKNFwYhKLwJ6IjMWZEStaLJsql3VSg_

So you just started to touch on the problem I am having, which is there is no resistance on the trigger to squirt the water out. ( when your camera came off it's stand). How do I troubleshoot for that problem? The water comes out of the toe squirt instant shot, and I checked for obstruction

@monroevac

2 жыл бұрын

Hi Judy I have a few video that diagnosed the handle- try this one- kzread.info/dash/bejne/lnist5Sqc8zepbQ.html

@monroevac

2 жыл бұрын

Also-kzread.info/dash/bejne/i3iosa2OqJq_mLw.html

You’re brave to touch those brushes bare handed not knowing what they been cleaning up with it lol

@monroevac

7 ай бұрын

Yeah you’re right not a good idea

We have the same bissel that you are working on in this video. no water is coming out of the machine. The brush cover and sides are already off when the video starts, i don't want to break something, but can someone give me advice on getting those pieces off?

@monroevac

3 ай бұрын

Try this video kzread.info/dash/bejne/mpibzNRrfJjMYaQ.html - there are other Bissell video in my playlist visit the channel page and you can browse the list

I can't remember where all the holes go to it's on Bissell pro heat 2 x I didn't take a pic of it

Tried everything and my machine still wont work. 😢handle and lever are good im not sure if it is sonething inside where the tank sits but how would i get in there to see??

@monroevac

5 ай бұрын

Sometimes putting another on the unit will help you zero in on the problem. For example, if you’ve ever used hot water in your tank it can warp your tank just enough to cause this issue. Try replacing the tank

Ok so I replaced the rod with the bearings on it because it rusted out. That got the motor spinning again. Now I can use the hose tools with no problem but when I use the lever to move the machine back and activate the carpet brushes, all that happens is the one shot nozzle sprays continuously. What did I do????? And how do I get the main function working again?

@monroevac

2 жыл бұрын

Which make and model- the description of your problem doesn’t resemble the revolution

@bigpun8601

2 жыл бұрын

@@monroevac definitely the revolution pet pro 2x. I replaced the rod with 2 bearings that transfers power from the belt to the pump. I’m the bearings were seized from rust. When I put I back together, I can attach and use the upholstery hose, but when I press the pedal to use the main carpet brush, the one shot nozzle on the size starts spraying and I am getting no water coming out at the brushes.

@bigpun8601

2 жыл бұрын

I can’t think of the term, but like on a vacuum you press the pedal and the latch holding the vacuum/carpet cleaner upright disengages and starts the brushes. I’m sure there is a term for this since it exists on all upright vacuums and carpet cleaners.

Could you do a stropdown of the machine the bissell proheat 2x revolution pet because that's what I did and I had to take out the lower hose that connects to the bottom floor head and to the external attachment hose I need to know how to replace it and put it back together because I bought a new internal hose to replace it with

@monroevac

Жыл бұрын

I’ll see what I can do. Would have to get on in the shop to breakdown

@Tymetraveller.martin

Жыл бұрын

@@monroevac alright that would be great because there is a ton of screws and the easy part was taking the machine apart but the hard part is putting it back together

I noticed the valve on the tank is not getting depressed when tbe tank is all the way in. Not sure why it is not pushing tbe tank valve up.

@monroevac

11 ай бұрын

The tank might be warped- if the water comes out when you test it with a pencil or your finger then the valve is working. Think back to see if someone put boiling hot water in the tank. You may have to replace the tank

How do you fix the water/soap knob on the right side next to solution tank

@monroevac

2 жыл бұрын

probably easier to explain if you saw a video. I'll reply again with the video link. working on it now

@monroevac

2 жыл бұрын

Hi Dawn just uploaded this video take a look and let me know if it helped-kzread.info/dash/bejne/pYOp19ORgbjAZaw.html

I'm having an issue where the solution keeps flowing to the main nozzle even if the trigger is not depressed.

Mine has water coming out just like yours but it's little to no water. Can it be a clog or motor going out?

@monroevac

2 жыл бұрын

clog is possible. but the motor really wouldnt be the first place to look for spraying issues. Pumps or the pump belt. Try changing the pump belt first.

My book says that if no water is spraying that I need to prime the pump by pressing something like an ink pen to prime the hose?? I pushed a pen into the little round thingy... but I saw no bubbles coming out so not sure if I did it in the correct place? No diagram. sigh

@monroevac

2 жыл бұрын

You may have to take the unit apart and check for the pump belt possibly disconnect the water hose line from the area that you stuck the pen in. check to see if the water at least reached that far.

I have no flow from the tank. Water comes out of the tank when I press the release on bottom so I poured water into the part the tank sits on and it pours out the bottom/handle of the machine, it doesn't flow through the hose at all. Now I can't figure out how to take the handle off to see if the hose came off inside.

@monroevac

Жыл бұрын

Sorry for the delay- try this video-Bissell Revolution breakdown- The dripping tank kzread.info/dash/bejne/ZIaNo6WffsqxcsY.html

Hey man, could you help me? Mine is bubbling up water from where the hose plugs in during normal use, but when nothing is inserted. Would you know of a way to fix this? Thanks!

@monroevac

2 жыл бұрын

I’ll look into it. Stay tuned

@darkriku12

2 жыл бұрын

@@monroevac thanks! And to clarify, it's where the hose attachment gets its water, next to the screw. Pen pressing inside there only helps a little bit. The orange 1548 model

@monroevac

2 жыл бұрын

Just uploaded a video that may help. Try this link- kzread.info/dash/bejne/iq2ax7SBc6vNiag.html

I don’t have a spraying issue but I do have an issue of after using the cleaner all the remaining water in the reservoir leaks out through the front where it auctions any ideas how to fix it?

@monroevac

2 жыл бұрын

Hmmm. So after shampooing and turning off the machine, all the extra water just pour out of the front nozzle. Then check for any clogged area. Possibly a part that is clogged can hold off the water in that area and then after the unit turns off it would just spill out

@noellestanbridge3211

2 жыл бұрын

@@monroevac will try to find if there is a clog.

Help!!! Bissell model 19863 Pet Pro 2X Revolution. Where the water flows down from tank it goes into a part that has two hoses attached. A large short hose and a long skinny hose. The large short hose goes into another part (which is the part I need I believe) which has two hoses attached and a spring on top. Both tubes travel down the right side to the brushes and I’m not getting water to flow. What is that part called, or item number, because no water flows (or air when testing) through it when pressing down on spring valve.

@monroevac

Жыл бұрын

Are you referring to the “cleanshot”- the button on the right side of the unit red and indicators when you step on it?

@bradmcallister

Жыл бұрын

@@monroevac thanks for the reply!! No, it’s where the little hole is in the back of where the handle meets the unit (roughly) but right below it on the inside. It is where the two hoses attach which travel down the right side. Basically you pull the trigger and it presses down upon the spring which (I believe) let’s the water from the tank flow downward (but mine doesn’t). I’ve taken the tubes off and pushed some low pressure air through the tubes which travel downward and it’s clear from there down, but not before to this point (between tank and this part at the beginning). Water will travel out of the tank into the first part but then leaks out of the back because it won’t flow through it. I took the piece off and nothing flows through whether I compress the spring down or not. Hope this helps.

@monroevac

Жыл бұрын

It’s called the auto receiver but Bissell do not sell this part for this unit- Unfortunately the other auto receivers that they do sell, won’t fit this one. Find a Used part on eBay if possible

@bradmcallister

11 ай бұрын

I have checked and water does come out of the tank and goes into the auto receiver, but there is where it seems to be stuck and will not flow downward and come out where the video shows around 6 minutes. I have tried to push air through and it will not go down the hose either. Sometimes a "little bit" of water will go, but 99.9% will not. I used really hot water in the tank and wondering if it melted something down the line inside the motor area, but the video says its gravity. Thoughts?

I really need help! I have the older model but they are very similar it’s the red one. I use it quite often I recently changed the belts took it all apart and cleaned it (lotta dog hair) worked so much better a month now and the trigger to spray has no resistance and the black hole you sometime need to prime for the hose with a pen or whatever is just dumping water from the tank. I highly need my shampooer to work as I have elderly dogs and lots of accidents please help!

@monroevac

2 жыл бұрын

Ok.. you’re describing two problems ..correct? The tank and the trigger?…

@monroevac

2 жыл бұрын

If the tank is just spilling out water you may need to replace it . Some Bissell cleaners allowed you to purchase the auto load assembly. But the revolution doesn’t. As for the trigger, the resistance problem may be the trigger rigger itself. Use a phillips screw driver and open the handle to see if the trigger is intact. There is a flexible spring like plastic that gives the trigger the resistance you are referring to; it may be broken. It’s possible to find the part on eBay. But most people have to just purchase a new handle. Part number for 1 gen revolution is 1609129

@autumnhiggs4344

2 жыл бұрын

Thank you! And I accidentally poke the prime a bit much which flipped that rubber seal inside out so I had fixed that but still no resistance with spray trigger for the main cleaning. I checked the hose attachment and it works fine so I’m going to replace the main trigger and cross my fingers it works. I take good care of my machines so I’ll be sad if I need to replace

@autumnhiggs4344

2 жыл бұрын

The issue I’m having is with the main trigger to spray out the bottom of the machine not the hose and all I can find is information for the hose attachment spray trigger it’s still suctioning just no spray with the trigger

@monroevac

2 жыл бұрын

I working on uploading a video about the spray trigger in the main handle. Inspired by your comment 😄 keep a look out for it. Should be up later this evening