I like the fluid control valve, can you tell me more about the one you used?
@bmf51503 жыл бұрын
Great video ,when mounting the pump and diverter did you tap the column or just put a nut on the inside ?
@joeknows496
3 жыл бұрын
Grade 5 through bolted
@drewmacvane2308 Жыл бұрын
What width did you go with? Your videos have been helpful for me, I just picked one up today. Thanks
@joeknows496
Жыл бұрын
120” Max center to center
@RelentlessRacingAJ Жыл бұрын
Cool video. Did you need the fluid control valve on the short hose side bc it was going up or down too fast? Which fluid control valve did you use? Link?
@joeknows496
Жыл бұрын
Guy at my hydraulics shop hooked me up I didn’t ask manf.
@dy45453 жыл бұрын
Hey, i was interested in purchasing one of these. My ceiling height is 9'8". what is the highest lockable position on this unit?
@toddk4115
3 жыл бұрын
Figure it out! lol
@jimzablocki9466 Жыл бұрын
I also have the c7000 but recently it has started going up crooked .. not all at once but as it gets higher ... I switched the lines around to make sure it wasn't in the flow control but it did the same thing on the same sides .... what do you recommend to fix this error ... p.s. I've tried rebleeding a dozen times it just won't straighten up
@joeknows496
Жыл бұрын
Sounds like your air bound , cycle the lift 7/10 times completely. Or install fluid control valves . Or when It starts to lift crooked, bring it down on the nearest locks and start over
@curtthompson27872 жыл бұрын
Nice install. How thick is your concrete?
@joeknows496
2 жыл бұрын
8”
@AbstractDreamz2 жыл бұрын
One year update? I am thinking about getting this one next month. How do you still like it?
@joeknows496
2 жыл бұрын
No issues works as it should
@kurtpaluch6914 Жыл бұрын
I am looking to purchase a C7000. I have a little over 4" of wire reinforced 3500psi concrete slab. Do you think that is sufficient? Edit: I just tested a few spots with a hammer rebound Humboldt tester. My concrete is between 4,500 and 5000 psi
@joeknows496
Жыл бұрын
I don’t think there should b any issues, but I wouldn’t use drop in anchors unless there knurled , @4” I would probably go with wedge anchors , though your portability may b an inconvenience . If you do go with wedge anchors b sure to drill completely through the concrete. That way , if you have a fastener fail you can just drive it straight down and into the soil under the slab . Watch your torque specs whichever way you go
@erikharestad52692 жыл бұрын
Can you lift a suburban on this?
@joeknows496
2 жыл бұрын
I lift my 1 ton on this . It’s rated @ 7000lb . My 1 ton/ utility body is 7400lb
@thereplacementfordisplacement Жыл бұрын
I like how you basically said the hell with getting 2 cars in the garage. I don't understand how that size garage is considered a 2 car garage, especially for a car guy. Liking cars and owning a bunch of classic cars you don't work on doesn't make you a car guy.
@joeknows496
Жыл бұрын
Im 28’x26’x10.6. most 2 cars spec at 24’x24x8’ ( that’s small) . Adding another 400sqft in the fall 2023
Пікірлер: 21
I like the fluid control valve, can you tell me more about the one you used?
Great video ,when mounting the pump and diverter did you tap the column or just put a nut on the inside ?
@joeknows496
3 жыл бұрын
Grade 5 through bolted
What width did you go with? Your videos have been helpful for me, I just picked one up today. Thanks
@joeknows496
Жыл бұрын
120” Max center to center
Cool video. Did you need the fluid control valve on the short hose side bc it was going up or down too fast? Which fluid control valve did you use? Link?
@joeknows496
Жыл бұрын
Guy at my hydraulics shop hooked me up I didn’t ask manf.
Hey, i was interested in purchasing one of these. My ceiling height is 9'8". what is the highest lockable position on this unit?
@toddk4115
3 жыл бұрын
Figure it out! lol
I also have the c7000 but recently it has started going up crooked .. not all at once but as it gets higher ... I switched the lines around to make sure it wasn't in the flow control but it did the same thing on the same sides .... what do you recommend to fix this error ... p.s. I've tried rebleeding a dozen times it just won't straighten up
@joeknows496
Жыл бұрын
Sounds like your air bound , cycle the lift 7/10 times completely. Or install fluid control valves . Or when It starts to lift crooked, bring it down on the nearest locks and start over
Nice install. How thick is your concrete?
@joeknows496
2 жыл бұрын
8”
One year update? I am thinking about getting this one next month. How do you still like it?
@joeknows496
2 жыл бұрын
No issues works as it should
I am looking to purchase a C7000. I have a little over 4" of wire reinforced 3500psi concrete slab. Do you think that is sufficient? Edit: I just tested a few spots with a hammer rebound Humboldt tester. My concrete is between 4,500 and 5000 psi
@joeknows496
Жыл бұрын
I don’t think there should b any issues, but I wouldn’t use drop in anchors unless there knurled , @4” I would probably go with wedge anchors , though your portability may b an inconvenience . If you do go with wedge anchors b sure to drill completely through the concrete. That way , if you have a fastener fail you can just drive it straight down and into the soil under the slab . Watch your torque specs whichever way you go
Can you lift a suburban on this?
@joeknows496
2 жыл бұрын
I lift my 1 ton on this . It’s rated @ 7000lb . My 1 ton/ utility body is 7400lb
I like how you basically said the hell with getting 2 cars in the garage. I don't understand how that size garage is considered a 2 car garage, especially for a car guy. Liking cars and owning a bunch of classic cars you don't work on doesn't make you a car guy.
@joeknows496
Жыл бұрын
Im 28’x26’x10.6. most 2 cars spec at 24’x24x8’ ( that’s small) . Adding another 400sqft in the fall 2023