Transient Stability Using ETAP 18 Lesson (10) for Power System Engineering Courses
Don't forget to subscribe to our channel for more electrical engineering online courses.
Get Khadija Academy Membership with access to lots of electrical, renewable, and math courses from here:
www.khadijaacademy.com/p/khad...
Watch this video to learn more about this membership:
• Khadija Academy Member...
Become a solar engineer and design different PV systems by joining this program:
www.khadijaacademy.com/p/comp...
Become an electrical design engineer and design distribution systems using Autocad, Dialux, ETAP,
and much more by joining this program:
www.khadijaacademy.com/p/comp...
Пікірлер: 38
Check out our Khadija Academy Membership for more awesome lessons in solar, wind, electrical design, wave, and much more: www.khadijaacademy.com/p/khadija-academy-student-membership
@bhooshanadlak8406
2 жыл бұрын
What is vvo ??
For Swing Gen is it can shown di Rotor Angle?
اسلام عليكم ورحمة الله وبركاته يا سيدي How are you sir I hope you will be good Sir I'm a big fan of you really you are good instructor. I always watch your videos based on etap. Sir i have a doubt regarding coordination of relays how to do that. Andy if we have a large network with large number of relays so how to do coordinate it.
@KhadijaAcademy
Жыл бұрын
Hey Azeem, In the future, I will add more videos about ETAP including relay coordination. I am currently busy with my master's thesis. That's why I haven't made this lesson yet.
Thank u so much sir!
@KhadijaAcademy
11 ай бұрын
You are welcome 🙏❤
Please tell me about the capacitive and inductive rating of SVC
Good teaching...thanyou so much
@KhadijaAcademy
2 жыл бұрын
You are welcome ❤
Hi.. why i can not plot syn generator rotor angle?
Sir, how simulation stability transient load shedding with UFR?
sir, how to find the derivative of a bus voltage angle in etap, pls reply!!
Dear sir A good teacher can inspire hope, ignite the imagination, and instill a love of learning.And you done it sir for us.Its our bad luck that we can not be a part of Your course due to some reasons but i personally appreciate your efforts .Allah Give you more.and Allah help us to become that part of Your Course in Future.Hope so Thank u sir
@KhadijaAcademy
4 жыл бұрын
Thank you Engineer Luqman for your kind words, I really appreciate this, don't worry this would be a free course on KZread.
good
@KhadijaAcademy
11 ай бұрын
❤🙏
Thank you very much for the video. But, I couldn't run the power flow. The error encountered was "Calculation process terminated abnormally exit code C0000135. Kindly help please!
@KhadijaAcademy
2 жыл бұрын
I would like you to try something, I believe that I have encountred this error long time ago. Try applying the crack again to Etap program.
Can i ask what about wind turbine generator in the transiant stability i have a massge bob up says wind turbine generator model is none at t = 0.000 sec can you help me
@KhadijaAcademy
2 жыл бұрын
You mean this error? kzread.info/dash/bejne/qZN_2NtpebPTgqQ.html
@user-eb3qo7qh6x
2 жыл бұрын
@@KhadijaAcademy yes thanks very very much it was very helpful
Sir, make more videos👏👌
@KhadijaAcademy
2 жыл бұрын
Sure I will, don't worry
Hi, I am facing problem when trying to run TS for my network this message appeares "TS calculation aborted due to excessive equivalent cable length at t=0.000 sec" Please i need a support Thanks...
@egramrt6812
3 жыл бұрын
i faced the same issue do u know what is the exact problem????
Sir. In generator, MW rate changing but inertia WR^2 value not changed. In inertia, RPM 1500 Always fixed here.
@SaminHosanAnik
2 жыл бұрын
Now, What can I do? Please answer me.
I have this error while running the study : calculation process terminated abnormally- exit code 9. And i don't know how to solve it can you please help me solve it?
@asmaanasser7394
3 жыл бұрын
Open the project file and drag the OTI file directly to ETAP
هل ممكن تقديم دورة باللغة العربية حسب الطلب ؟
@KhadijaAcademy
2 жыл бұрын
اتمنى يا اخي ولكن صعب بسبب ضيق الوقت المحتوى باللغة الانجليزية للوصول الى اكبر عدد ممكن من الناس
That is great. but one mistake that you have : secent transformer is 12.5MVA but you put 125MVA
@KhadijaAcademy
3 ай бұрын
Thank you! I wish ETAP says "Hey you can't do that "😂How are you using a 125MVA transformer for a 10MW generator :)
Hi AHMED , How can I get or install etap. Is that free program or need to make account. Thank you in advance
@KhadijaAcademy
2 жыл бұрын
Hey Maas, you can find it here: www.ieees.com/f-9/11836/ The program is not free, it is paid, but the link contains a cracked version
@maas2825
2 жыл бұрын
@@KhadijaAcademy Thank you so much
thank you for this video. I have a problem with my system. I need some help. can I have your email?