Thanks for taking the time to make a video about this, it is somehow comforting to see it done before you get at it yourself! Especially for a first time tractor owner like myself.

@farmboy30117

7 жыл бұрын

Thanks bud! Just be sure you get the old seal out and the new one in at the top of the filter. Sometimes the old ones like to stick in there.

This video is AWESOME. I have never worked with the diesel fuel filter before and was a little worried. After watching this, I went out and changed it with no problems. The old Ford 3930 is running like new again. Thanks a million. And I can understand you just fine. Don't worry about the city folk that don't understand ya, they don't have a tractor anyways.

Great video, covered everything. I just resurrected a 6610 II and this helped me figure out what bolts to turn. Tip- the glass sediment bowl has three gaskets

That's great Bill! If you continue to have fuel issues, I'd recommend pulling the shutoff valve out of the fuel tank and checking the strainer. They tend to get clogged over time.

Thanks for the informative and clear instructions. I would have forgotten to dig out the old ring in the housing and had a big leaky problem.

Farmboy, great video. Helped me trememdously. You should get your own TV show and show the masses what you know. CR from Michigan

@farmboy30117

10 жыл бұрын

Thanks CR. I don't know about getting a TV show. I'd imagine they'd have to use captioning when I talk like they do the other southern shows. LOL

Success! I changed the filter on my 1975 ford 4000 after watching this. I never had feul come out of the bleed valve, so I turned over the engine. That probably pulled air into the line, so then I had to learn how to bleed the system. I'm hoping this solves my loss of power problem. I also watched the ford 3000 routine maintenance video. That looks very, very similar to the 4000.

Thanks for making this video. My tractor was running very poorly, I decided to change the fuel filter. Wouldn't start and then found the bleeder and she started right up. Your video was helpful.

@oilfilters1893

8 жыл бұрын

+Bourne Accident you need good quality oil and filters

@BourneAccident

8 жыл бұрын

oil filters For sure. Thanks.

@farmboy30117

8 жыл бұрын

+Bourne Accident Glad it helped!

Good video! I have these filters on my Long an I despise them!! Lol!! I’ve never been able to get them to seal up the first time without fooling with them and getting drenched in diesel! Lol

On my kubota it was low power and blowing white smoke out the exhaust and the mechanic on the phone said that meant it was starved for fuel. I changed it and got 100%

Wish I saw this a couple of weeks ago, my ford 3500 was dying all over the place, changed the fuel filter BUT put the upper big washer in wrong and was still running out of fuel worked it out by putting the correct orientation and is running ok. been stuck all over the property bleeding the filter the injector pump and the inj. lines. this has been going on for a couple off weeks. got write before seeing your video, you made it very clear on how to do it. Thanks

@farmboy30117

9 жыл бұрын

Yeah, it's a real pain to have to bleed the injectors. I'm glad you got it straightened out.

I'm glad it helps. Thanks for watching!

Thanks for the great video. I just got my dad's old Ford 3910 tractor as a hand-me-down. Never used a tractor much before, so I have a lot to learn. You tractor's fuel filter looks identical to mine, so hopefully I can change it without much difficulty. Thanks again.

@farmboy30117

7 жыл бұрын

Thanks for the comment! I hope it helps, the biggest issue on these are getting the O-rings (don't forget the one on the bolt) on correctly and bleeding it before trying to crank.

Thanks for your video, I was interested because my 1994 Ford/New Holland 6610S after warming up would surge then die. I replaced the filter and cleaned the bowl, I disconnected the lines and blew air through them to dislodge any trash, I took off the check valves from the injection pump and cleaned them, I changed the fuel filter again, I found the fuel primer plunger was sucked down each time it died, aha cavitation, I replaced the fuel cap . . . still surged and died. Finally I removed the shutoff valve AND strainer. I sprayed carborater cleaner inside the tank and took a small rag on a coat hanger and swabbed up any trash and cleaner and Bingo, so far so good. After thinking more about the strainer, I should have left it off and allowed the primary filter to catch the trash. It's much easier to change than draining the tank and removing the shutoff valve to get to the strainer. I hope this helps someone else.

Farmboy 30177, Thanks for the upload! Plus you sound like a good ole country boy, hell you would fit right in around here!

@farmboy30117

9 жыл бұрын

Thanks Toby.

Good video, had no idea how to change the fuel filter on my dads ford 3000 tractor. Watched one video (this one) and done it. Love the roosters in the back ground

@farmboy30117

10 жыл бұрын

Glad it helped you out! Thanks for watching!

Good video it's amazing what a new fuel filter will do

Great video. Hats off to the Southern boys.

Bang on thanks! Had a go today on my Dexta - worked a treat!

@farmboy30117

6 жыл бұрын

Awesome! Glad it helped!

@volvo906

6 жыл бұрын

farmboy30117 - it did thank you - 59 and just introduced to a tractor! - still that’s England for you!

Great, thanks for sharing. I need to change mine and clean the prefilter. This is a little different than changing the filter on my diesel truck, since the tractor is gravity fed.

@farmboy30117

9 жыл бұрын

You're welcome. Don't forget to change the gasket in the prefilter.

Thanks Man!!! Cured my problem too!

@farmboy30117

7 жыл бұрын

Happy to help!

Thank you, helped me a lot.. Mississippi

@farmboy30117

8 жыл бұрын

+Bob Parsons Glad it helped Bob!

Thanks for the video, very helpful!

@farmboy30117

5 жыл бұрын

Glad it helped!

thanks enable me to see how to change the primary fuel filter on my boat! Excellent

Great video...3600 was the best tractor ford made

Don't have much experience with a Kubota but glad it straightened it out. White smoke don't sound good.

Another great video. Thanks

@farmboy30117

5 жыл бұрын

Thanks Mark!

excellent video. Thanks

great... got a skid steer that runs ok then after a minute starts bogging and rpm goes down.. sometimes stops ... cranked up the throttle and usually runs at 2300+rpm.. then drops to 1500 rpm erratic up and down... checked all fluids topped up.. before this started i put in some diesel engine treatment then the issues began... i drained the tank ran it dry and guess i know i got air in the system... going out in a bit to bleed the fuel system... and check the fuel cap .. u made a good video two thumbs up ...

Helped me! Thanks

Thanks Farmboy time to do mine tomorrow

@farmboy30117

7 жыл бұрын

Thanks! Hope it helps you out!

thank you I will look in to it.

When I change out my filter and have air in the line I just pull start it. Much easier.😁

Thanks!

Thanks for sharing... helped me... Nice Accent :)

@farmboy30117

9 жыл бұрын

Glad it helped!

I believe there is. Yeah, it's been very dry here all year

Oh that's right,When I use to mow the road sides I ran a Ford 7700 and I use to have to crack the injectors once in awhile.But it was yellow,and I've always vowed never to buy nothing yellow,cause that spells a lemon.

Nope, you have to crack the injector supply lines open to bleed the injection pump. You should make some videos. It helped me get some projects done. I'm a big time procrastinator!

I've not changed the one on the old 4000 I bought for bush hogging and seldom use , but it's nice to know the symptoms and how to change it out when it needs one. thx

The other filter is a sediment bowl. I think it does use the same gaskets as the fuel filter though.

Thanks farm boy great video,i have a MF 35 I geuss it would be the same on that tractor but is it the same for the other filter along side

That fuel filter had been on there probably 4 yrs. I usually change them every other year as routine maintenance but I wanted to show what happens when one clogs.

Thanks! Good clear instructions. I can probably do this myself

@farmboy30117

8 жыл бұрын

+Barbara Ellin Fox You're welcome!

No problems with mine. Does the alternator have an external regulator? If so, it may need to be excited. I had that issue with the Ford 3000 but it has a generator. If not, check all the wire ends to be sure they're good.

I don't think so on the filter but it may be one on the pre-filter that I didn't mess with. We haven't had any issues with water contamination.

Thanks, I will

If its really cold it could gel. If its old fuel, I'd definitely blow those lines out. All the plastic fuel lines I've seen have been hard. I think it may be the type of plastic used.

thank you for the videos. I have a 3930...my first tractor ever. I am not mechanically inclined so thanks again for the videos. Question for you...what is the easiest way to drain the gas. I accidentally got water in the tank. I haven't started it up...so I think draining the gas should do.

@farmboy30117

8 жыл бұрын

+Austin W You're welcome! I'd break the fuel line loose at the filter and let it drain out. Once it's drained out, you can unscrew the shutoff valve and check the strainer in the tank.

good person

thanks would have messed up without this

@farmboy30117

9 жыл бұрын

John Brown You're welcome!

ok thanks... Im sure that it diddent gel because #1 theres no diesel in the tank lol just found that out. And here in Texas... yeah it doesn't get cold at all.That solves alot of problems that dont have to worry about. And the reason i asked about the plastic lines is because ive worked on sports bikes and some of the fuel lines are bendy like. well tommorw afternoon im working with the air compessor. yay XD

LOL, I've been thinking about it!

@annegreene9535

3 жыл бұрын

Is this electric pump?

@farmboy30117

3 жыл бұрын

@@annegreene9535 the pump is mechanical and is gravity fed from the fuel tank.

Thank you! Now you have helped getting a tractor running again i Norway. :-)

@farmboy30117

8 жыл бұрын

+dasvfa You're welcome, glad it helped!

@twb605

8 жыл бұрын

+farmboy30117 Your video is great, but my knowledge level is not where yours is. Do you suppose we could talk over the phone? I have some questions related to my 1965 Ford 4400. I just replaced the dual fuel filter with a single filter housing and think I might not have the directional arrows from the filter housing going to the right place on the injection pump. My injection pump looks a lot like yours. Which is the inlet, the one on the side or the one towards the gas tank? Also, I read somewhere the injector pump holds oil. Is there a level plug on the pump? How do I know if the oil level in the pump is OK? It has always run good and started easy. This started when I replaced the leaking diesel fuel tank with a new aftermarket. The threads in the dual filter housing were shot because someone has used a pipe thread hose barb. My email I see each day is twb60@yahoo.com. Thanks - T Byrd

@farmboy30117

8 жыл бұрын

I've never heard of the fuel pump holding oil. It is gear driven off the timing gears but I don't think it holds oil. All you need is a line coming from the tank going to the filter at a "in" port and a line coming off the filter to the pump in an "out" port. If needed, I can make a video showing how ours is plumbed.

@twb605

8 жыл бұрын

+farmboy30117 I am good on from the fuel tank petcock to the "in" port on fuel filter housing, but the fuel filter outlet has 2 lines. One line goes out and the other back in. The line coming out of the filter housing goes to which of the injector pump locations, the one on the side of the pump or the one on the rear (rear meaning the end of the injector pump towards the fuel filter. Mine has flexible fuel hose for a section between the filter housing and pump and I could have gotten those 2 lines crossed. If I am feeding the pump at the pump outlet, it will never prime. Looking at yours in these video, I think I did cross the lines.

@farmboy30117

8 жыл бұрын

Yeah, it should go to the side of the pump.

You ever have an issue with the charging system on this tractor? My 4630 alternator checks out good but still no charge to the battery... Any thoughts?? Idk if its a short some where or what but its driving me crazy..

They're steel except the one going to the injection pump and its plastic. I've had to mess with the plastic one on the Ford 3000 and it's a pain.

Thanks. Have you ever replaced the seals in fuel injector pump? Mine is leaking. I'm assuming replacing all the seals that come in the kit, and then bleed the air out.? Any input is appreciated. Thanks!

@farmboy30117

9 жыл бұрын

I've never messed with an injector pump. I'll assume that once all the seals are replaced you'll have to bleed the injectors to get fuel to them just like when you run out of fuel.

Copper fuel lines they look fun to replace

my filter is in 3 parts. 1 steel base,2 glass bowel, 3 filter.Is there a rubber ring between all 3 parts.Its a M.F 698.Thanks for vidio.See ground conditions very dry over there not like Ireland.Muck up to our ears

has anyone heard of diesel gelling in a motor? just wondering because im trying to clean my old tractor motor out and im just wondering if i need to take all of the fuel lines off and clean them if it does. and just wondering but are plastic fuel lines suppost to be really hard?

To be honest w-out it being in front of me idk.. I know its just like your 3930 just with a turbo.. Had it rebuilt by a shop i have had good sucess with but put er back on and still no charge.. I will check tomorrow about the external regulator, thanks for the reply..

I their I have a 1951 ford 8n 4 cyl gas tractor. I am having problems with the 3 point not staying in the up position while driving the tractor. Their is a box scrapper attached to the 3 point hitch, the hydraulic lever is raised in the up position, but implement still goes down while driving the tractor. what could this be? thank you.

Sounds like you have some seals leaking by in the hydraulics.

My Ford 4000 loses fuel prime if it sets for a week or so. Eventually I can get it going by repriming it, but it loses its prime after about an hour of operation. Then I have to start all over again. There seems to be air getting in somewhere because when I open the screw on the injector pump there is some air in the fule there and when I pump the reprime pump below the injector pump there is air there. Of course there is no fuel at the injectors on the head themselves until I get the air out of the system thru the button pump. Just before the engine quits it accelerates like it got a rick mixture or some more fuel and then it starts sputtering. Ideas?

@farmboy30117

3 жыл бұрын

Sounds like you're getting air in the system between the tank and the injector pump. Could be a bad filter or filter housing letting air in the suction side of the filter.

@Ramdinohikes

3 жыл бұрын

@@farmboy30117 The suction side is after the filer and on the injector side corect? FIlter was changed last year less than 50 hrs ago and has run good since then. Does the surge in RPM's right before it cuts out mean anything?

What is the glass bowl to the left of the filter you changed? Is there anything in the bowl that needs to be replaced when changing filter? Thank you.

@farmboy30117

8 жыл бұрын

It's a sediment bowl like a prefilter. You can clean it if needed but you will have to reuse the bowl gasket or buy another filter for a new gasket.

Thanks

@farmboy30117

4 жыл бұрын

You're welcome!

I would have thought you would have checked the first filter first, the one with the water glass on. That s the one that blocks first,

It's just a sediment bowl. I shoulda cleaned it out but was in a hurry to finish bush hogging

Hey farmboy I bought a Ford 2000 today and when I got it home and started it , it started smoking a bit from the exhaust and then surged and quit. It never started again. Maybe the same problem as yours? Did yours smoke?

@farmboy30117

6 жыл бұрын

No, mine wasn't smoking when it surged. Hopefully yours is as easy to fix as this one.

How do you get the orange housing off to remove the fuel tank? We have changed fuel filters twice, fuel pump once, and have no other options except to get the tank off and try to see inside that. The Kubota dealership two years ago had it in, charged 800 dollars and the same problem existed after we got it back.

@farmboy30117

10 жыл бұрын

There is a lot involved in removing the tank. I would suggest siphoning the fuel out of the tank and unscrewing the petcock. There is a screen inside that's probably clogged. Once you get it off, flush out the tank with fuel to get any loose rust out. I left the screen off on my Ford 3000 because it kept clogging. Now I just let the filter catch it.

Hey I have a ford 545d tractor changed fuel filters didn't do the bleed screw now I have air in the lines tries cracking the injectors can't get any fuel to come out it will hit when I do the bleed screw but just for a second any advise

@farmboy30117

10 жыл бұрын

Hard to tell without seeing it, but if you've got fuel in the filters, try cracking open the little screw on the side of the fuel pump. Should see fuel come out. This will let you know if you've got fuel to the pump. Once you have fuel to the pump, you should have fuel and air coming from injector line while cranking. Keep bleeding the injector lines until mostly fuel then tighten them down. Hope this helps.

Just out of curiosity, do those tractors have a Ford or Perkins in them?

@farmboy30117

7 жыл бұрын

It's a Ford in this one.

It would also be helpful to know how much time you let the bleeder valve stay open.

@farmboy30117

2 жыл бұрын

I leave it open until a steady flow of fuel with no air appears.

Ok thanks. Some there is no filter above the bowl?

@farmboy30117

8 жыл бұрын

No,, just the housing

Nice upload - thanks - looks almost the same on a Ford 4100. But next time please put something underneath to catch the fuel when removing the filter. Not so great with all that fuel on the ground :-(

I don't no why every filter isn't a spin on!!! they should be!!!

@option311

9 жыл бұрын

Nah, these kids that are taking engineering have to make their mark reinventing the square wheel. Anybody designing anything but spin on should get a "F" and be booted from the class and told find another profession.

come to think now....it might have been blue smoke?

Hard to steer

Just did that on a 655c backhoe and imagine the Donaldson filter was made in Saudi Arabia. Too late too change. I thought they only made terrorists. Main thing is why didn't you clean out that sediment trap? Looked terrible dirty. If your going to tear into the fuel assembly, drop that glass bowl and show folks how to put it back in. My assembly has a priming pump, but otherwise its the same for most all for backhoes up to the New Hollands from Italy.

@farmboy30117

7 жыл бұрын

Haha, I've never even tried cleaning that sediment bowl. I figured it'd need a new gasket that I don't have.

@RRaucina

7 жыл бұрын

I open mine every 200 hours or so and find a lot of slime. I reuse the gaskets [not o-rings - square profile] so far for about 3,000 hours and they are fine.

@RRaucina

7 жыл бұрын

Actually, to correct myself it's more for a water trap, but collects dirt too. Opening the bottom drain every few tank fulls usually show quite a bit of water. I just bought that glass bowl on ebay for like 4$, but no gaskets

@farmboy30117

7 жыл бұрын

Thanks for the info! I assumed it would use the same gaskets as the fuel filters since it's basically the same housing. I never thought about it being a water trap. I'll definitely clean it this spring before hay season!

Hi! Cool video. We have a Fordson Dexta tractor that has a fuel filter housing that looks like the picture I put on Picpaste.com. Could you please look at it and tell me what the bolts are on top. One is marked "OUT" but the other one isn't marked. We think the center bolt is the bolt you unscrew to take off the fuel filter housing, yes? picpaste.com/9_fuel_filter-oisyONd8.JPG We have the Fordson Dexta service manual (it's free on the internet) but it shows a different type of fuel filter housing, one with a bolt on the bottom, not the top, and the bleed bolts are in different positions. Thank you for any help. Sincerely, kl

@farmboy30117

8 жыл бұрын

The center bolt holds the housing on. The other two appear to be bleeders. Maybe one is for the inlet and the other for the outlet. Not sure why it'd have two bleeders.

@kathyloften7055

8 жыл бұрын

Thank you very much!

@RRaucina

7 жыл бұрын

Yes, the center screw is the bleeder. The two other bolts hold the sediment cup and filter. Drop the sediment cup and clean that too. Some have bleeder screws on the injection pump and others have primer pumps.

1971 ford 3000.trouble started when i replaced with napa filter.thought pump was bad.took injectors and pump to shop to get built.$850.still got trouble.bleeding.fuel to filter,nothing coming out bleeder on top.so i take base off.can't figure out how it works.arrows on top.I NOTICED NO HOLES IN TOP OF FILTER.dam it napa.this video shows same filter with 4 slots cut to let fuel in to be filtered.i see another brand on line that has round holes in top.my napa filter has none.screwed again by free trade act.china or mexico idiots can't do nothing right.

@farmboy30117

8 жыл бұрын

Wow, sounds like it was mis-packaged or something. I've never had issues with Napa fuel filters.

Thanks!