TP4056 module modification for more lithium Batterys
TP4056 module modification for more lithium Batterys.
This is experiment only but you can try. Because this was working.
Components used in this project:-
1. TP4056 Lithium Battery charging module.
2. TIP3055 Transistor
3. 56 Ohm 1W or 2W
4. 1K Resistor
0:00 - Circuit Assembly.
2:08 - Testing.
4:43 - Testing 18650 4 Battery's.
#tp4056
#diyelectronic #tp4056_module #batterycharger #18650 #homemade101
Пікірлер: 74
DIY Power Inverter 12v to 220v : kzread.info/dash/bejne/fWGbtayHmcvLiaw.html
That 0.5A is current drawn from the 3P battery due to equalizing its voltage to a 1P one. This is why the current goes down, the 3P battery become slightly discharged as it slightly charges the 1P one. Furthermore, that transistor end up in saturation (due to heavy base current) connecting the B- (collector side) to the ground (emitter side), which does virtually nothing to the charging current, because charging current still goes through TP4056, because this IC regulates the current at the positive side. Changing that programming resistor to 1kΩ increases the output current to the 1.2A, which is kind of unfortunate as the TP4056 is rated to 1A max. This modification is nothing than a nonsense from its beginning to the bitter end.
@homemade_101
14 күн бұрын
thank you
@MrFlagstaf
12 күн бұрын
@@NikiBretschneider nice! that was my thought from the very beginning. You confirmed it, thanks! Absolute nonsense
@kailasingle460
8 күн бұрын
One cell of 4.2 v How much max current we can give?
@DARKNESS19906
7 күн бұрын
@@NikiBretschneider yeh!! Your right 👍👍👍👍
@emanikebiz
3 күн бұрын
@@NikiBretschneider HI. donde te puedo escribir?
Hi, is it posible to mod drone remote control so it can yaw smoother?
@homemade_101
11 күн бұрын
yes,.. you can try it
Wow! That’s cool. If this could be done , may I know is it possible to do one mode similar to make a 3S bldc esc into 200v bldc esc ? I didn’t see anyone doing this yet. Thanks ❤
@homemade_101
12 күн бұрын
welcome. try
nice but how to charge them when they are in a 4s configuration?
@homemade_101
21 күн бұрын
This connection is not correct. If so, we should do a separate battery charging by banning with a 4s balancer circuit. I made this as a test for this module.
@noanyobiseniss7462
21 күн бұрын
@@homemade_101 I was considering using a NC relay for the 4s and pull it when the charging circuit activates but then i'm not sure if the relay will fail open or closed and that would be a fire hazard. also considering i wish to use it in a battery back for my old hammer drills there would not be room for the 3 high power relays that would be needed. I could use a A triple-pole switch but i don't like manual control especially if you forget then you fry the system.
من العراق احييك ايها الانسان البطل فعلن لديك ابداعات قيمة شكرا جزيلا لحضرتك 🌹
@homemade_101
17 күн бұрын
thank you and welcome
@user-gj3jy1qv5u
5 күн бұрын
@@user-wh1hu6sd4u Что за каракули ?
😂😂😂 5amp not 500 mah only😅
@homemade_101
20 күн бұрын
Ignorance is visible.
Зробив зарядку на 0,5 ампера🤷
@homemade_101
20 күн бұрын
yes i thik battry was charging
Co to je? To máte v Indii nějaké nové hodnoty pro Ampery. Toto je velký fail.
@homemade_101
18 күн бұрын
okey
Multumim,bine venita inovați,merita abonat ❤
@homemade_101
21 күн бұрын
Bucurați-vă și bun venit canalul meu.
О мой индийский друг! Я сначала не узнал тебя в перчатках. Когда пойдешь в майкрософт работать?
😂 Какой смысл ставить транзистор пипец😅
@homemade_101
8 күн бұрын
@user-gj3jy1qv5u
5 күн бұрын
Вроде как усилитель тока ?
the ic max current output is 1 amp only.theres no way this could boost current output.. cant full everyone though
@homemade_101
12 күн бұрын
full everyone
Dear you are creative. The first question, what is the benefit of the 1 kilo resistance? Why didn't the blue LED light up after the complete charging? Thank you.
@homemade_101
21 күн бұрын
A carbon film is used because the SMD resistor burns when a large current is passed. It will not turn blue because the batteries are not charging at the same time. A balancer will be used for this.
@hanymagdy2095
21 күн бұрын
means that after the charging is complete, it turns blue and thank you
@homemade_101
21 күн бұрын
@@hanymagdy2095 welcome
Now this board 2amp?
@homemade_101
10 күн бұрын
yes
Not work. TP4056 out 4,20V - 0,65V Base = 3,55V out insufficient charger
@homemade_101
18 күн бұрын
what
@sencerylmaz3375
18 күн бұрын
@@homemade_101 you are a fraud
These TP4056 boards cost 1.5$ for 10 of them, but 🤡 "forgot" to measure voltage on cells after current fell to 10% of nominal.
@homemade_101
3 күн бұрын
yep
ایده بدرد نخوری بود نیم امپر 😂😂😂
@homemade_101
5 күн бұрын
Very good First time i saw a real video on this topic on youtube.
@homemade_101
21 күн бұрын
thank you bro
Nessa configuração esse transistor não está servindo para nada 😂😂😂😂😂😂😂😂😂
@homemade_101
12 күн бұрын
ok
what the purpose of this? to increase the fast charging?
@homemade_101
15 күн бұрын
Stop burned the module
@curits8260
15 күн бұрын
@@homemade_101 thank you for the reply. this is good idea to stop burning module.
Carga lenta
@homemade_101
17 күн бұрын
yes sorry
i'll tray it in my project to
@homemade_101
21 күн бұрын
good luck.
💯💥Good job
@homemade_101
19 күн бұрын
thank you
Μπράβο πολύ έξυπνο. Συγχαρητήρια.
@homemade_101
18 күн бұрын
thnaks
И нахера там транзистор если все всеравно идёт через микруху, она и ограничивает ток, максимум может дать 1А заряда. Читай даташит и схематику изучай тормоз!
@homemade_101
9 күн бұрын
sorry
@MrGekson
9 күн бұрын
Последовательно с микросхемой еще транзистор. Ну да смысла от него нет. Это наверно если шунт в его цепи ставить, который микросхема будет анализировать.
Sorry brother it is taking current more than the cell's limit. In this way you are killing that battery. Can you limit the current below 500ma
@homemade_101
5 күн бұрын
thank you
Super❤
@homemade_101
20 күн бұрын
thanks
??????????????????
@homemade_101
8 күн бұрын
why
Thanks 🙏
@homemade_101
20 күн бұрын
welcome
everything he did makes no sense. You could just hook up the rest of the batteries
@homemade_101
7 күн бұрын
yes you are
Get some real knowledge 😂😂😂😂😂
@homemade_101
15 күн бұрын
😄