I’m new in this field and I’m learning a lot from watching your videos. I appreciate the videos you upload. I’m hoping to get to your level at one point.

@empilhadicas5754

Жыл бұрын

Forklift not driving forward new vídeo Channel link kzread.info3J83DeIDdhE?feature=share

great presentation. on trucks with high hours I have found that the internal strainer filter in the valve chest ontop of the transmission gets blocked. often people just replace the filter. if you don't flush then change the ATF and filter it will block again. once again I learnt that the hard way.

@Raintree29

Жыл бұрын

Where is that I've replaced both solenoids and seals on cylinders and still no forward .. not a wire we tested and not controller ?? I'm lost

Thanks, great video, after your pico scope video I was inspired to watch the rest of ur vids for while I may not work on forklifts, I appreciate your methodology.

@forkliftgeek10

7 жыл бұрын

+Nathaniel Reid thanks.

@forkliftgeek10

7 жыл бұрын

+Nathaniel Reid thanks

Very helpful. Will try to fix my forklift with same issue

Thanks for the check light thing, never thought of it it also would limit current vry cool and the t-pin type will change how I do things moving forward, like every day. You should get a Fluke multimeter, this would take like 3 minutes without any power involved.

@forkliftgeek10

4 жыл бұрын

I do have a fluke multimeter. I like using a test light on simple loads such as relays, lights, solenoids because its quick and easy to do a bypass test. The bulb would limit the current going through, as you are basically connecting the test light in series with the load.

Hello colleague, excellent video and explanation of the follow-up of the failure. question, can you share the technical information of that equipment, the electrical system diagram, best regards, Milton Apraez

Thanks for your good information

Ur badass man I hope one day I can be like you I just got a job at distribution place as a forklift mechanic and I just ran into this problem

@forkliftgeek10

7 жыл бұрын

+David Torres glad the video helped you out. Tnx

Looks like the truck have in built analyzer..enter the pass key, get to the analyzer mode and to I/O Travelling...

Useful video please make a video of godrej forklifter to same problem

@forkliftgeek10

3 жыл бұрын

Sorry, we don't see this brand in North America.

We replaced both solenoids and it still doesn't work .. not a wire problem or a control switch problem ..

Thanks super helpful

nice videos thanks I have question I have forklift hyster h50 xl start but when I push pedal for aceleration cut off I have to put my hand on hold fron air filter runs fine if I take my hand off the forklift cut off

Hey buddy, im having problem with no forwards or backwards, i have power to either side of plug to solenoids on transmission when switching lever to forward or revers, also done a bypass test. so we stripped the transmission, the solenoids seemed fine when we tested them as we could hear them opening or closing when power was put to them, all internals of transmission looked fine as far as im aware apart from internal strain filter which was clogged. but cannot see any other problem internally on transmission, still yet to put transmission back in but struggled to find any issue at all, where else could i look?

@forkliftgeek10

Жыл бұрын

Check the spools for clogging

From already thank you very much

Hello boss my forklift here seem broblem no forward only revers can direct batery curent have i, change all clutch pak. All oil ring oring all. But seem no forward. What is the problem this thank you

I have one with the same issue. Solenoid and clutch packs are fine as I had it going forward with a bypass test. Direction switch works and It can't be the relay as swapping the relays around doesn't swap the fault. Must be a broken wire somewhere surely?

@forkliftgeek10

5 жыл бұрын

More likely but check at the relay socket. U should get 2 grounds and two 12v when the switch is engaged.

@vijayVijay-pe5ve

Жыл бұрын

How did you fix direct to check? Could you please answer me?

Good 👍🏻

having a similar problem.but was told its a transmission issue

hey how do you fix a seized tilt lever? my tilt doesn't come back to neutral after up and down moves

Onsa daot dli mo atras ang forklift pero og abante modagan

Got any videos on how to handle AD-4 AD-3 error codes on a Toyota 7 series?

I have the same problem but I don't know if it is the command lever or some relay

Sir The automatic forklift have adjuster clutch .

@forkliftgeek10

2 жыл бұрын

I think what you are referring to is the inching valve. On a forklift the third pedal is called an inching pedal which releases the forward or reverse clutch for the operator to feather the movement of the forklift or to release the clutch completely.

Hey I’m working on a Toyota forklift and I’m not getting forward or reverse on it and a error code of ad-7 for a can communication issue please help

thank you

I have Kipor 3ton forklift with short-circuit on reverse circuit. Please will you assist?

Looking for manual for a very old TCM model FVB25 H4 with Hitachi SCM4 SCR controller. I really need circuit diagram.

I encountered the same problem today, the solenoid for forward os defective, i put 12v but its not moving.

Do you by chance know what woul$ make a Nissan k25L engine,, crank idle good but it won’t rev up 2008

@forkliftgeek10

2 жыл бұрын

Its probably in limp mode. Check if there is any code present.

Unos delomejores equipo para trabajarle es el Toyota me gusta trabajarle a ese equipo

@josecegarra2057

4 жыл бұрын

¡Hola colega! ¿Por casualidad tienes el diagrama eléctrico de ése montacargas o el manual? Te agradecería si puedes compartirlo conmigo. Mi correo es jcegarra64@gmail.com

I use TOYOTA forklift. Now days TOYOTA MODEL: 6FBRE14 electroforklift steering wheel is not working. I couldn't find service center of TOYOTA from UZBEKISTAN. Can you help me to fix this problem?

Y wue fue lo wue cambiaste en esta falla ke presentas

Just started working on toyota lifts at work . I have a 8fgcu20 I think , smaller hard tire dock forklifts and when you hit the brake pedal going forward it will almost throw you out the seat , when in reverse they operate normally and gradually stop you without jarring any tips ?

@forkliftgeek10

4 жыл бұрын

Sounds like something is jamming in the brake drum going forward.

I have the same issue and completed all the troubleshooting procedures you posted. I do have power on my assembly switch and when added 12v to switch wheels move forward. Is my issue coming from the relay? Thanks in advance

@forkliftgeek10

Жыл бұрын

Relay or wiring from relay

@DanielCollum-jq3or

Жыл бұрын

Where would the relay be located

I have RR B3 reach truck error E107 occurs after some working with reach truck. Anybody tell me what is the problem. I have replaced the battery but same condition

hello i have 1 problem, toyota geneo R 1.5 ton forklift. error code fe -2 fe-1 . when the car is going fast, it gives an error and then it runs at a slow speed, please help me

Cvt transmission angage reverse gear but no angage farward gears possible problems? I am auto engineer filter wash cvt fluid change but no result please solve problem this is mechanical problem or electronic?

Help I have a FGU30 TOYOTA RUNS GREAT IN FORWARD COUGHS AND SPUTTERS IN REVERSE

1DZII DIESEL ENGINE SERIAL LOCATION PLEASE? WHERE ON ENGINE BLOCK DO I FINE IT? THANKS

I have Toyota lift and cannot find the manual. when check transmission fluid level do leave the engine running while checking fluid

@forkliftgeek10

8 жыл бұрын

+Mathew Hansen no. On the dip stick there is a level for hot or cold. I usually run the engine to running temp, kill the engine then check the level using H as reference.

Invest in a power probe

Hi I my company has a Toyota forklift model #8FGCU30. Original problem was lift jerking when in forward gear then lift was not driving forward or reverse. We changed both solenoids, torque converter and replaced all the parts in the transmission. Now lift moves forward but does not reverse, engine only revs. Any advise will be appreciated. Thanks.

@forkliftgeek10

7 жыл бұрын

+narad phargoo have you tried the test in this video?

@naradphargoo7480

7 жыл бұрын

ForkliftGeek hi i did not try the test yet. will let my tech know. do u have an email address where i can communicate with u.

@forkliftgeek10

7 жыл бұрын

+narad phargoo look me up on instagram and direct message me there.

Cual era el problema? Soleniode? Tengo un problema iguan con un 8FG30, con control de marchas en la columna de direccion.

@forkliftgeek10

6 жыл бұрын

+Susana Rueda sorry, dont understand much spanish..

@BlackSkuLL4u2

6 жыл бұрын

Forklift geek that what was the problem u didnt had a conclution

i have attended one concern for Toyota forklift. in this forklift up and down move not working. hydraulic pump solenoid switch current do not come. all fuses ok but one relay ignition current do not come. please help me sir

@forkliftgeek10

7 жыл бұрын

+KUMAR D I would suggest acquiring the schematic and tracing the wiring.

my heli cuts out everytime the reverse alarm beeps

Hi I have mitsubishi for klift and same time is show f85 then is not moving forward and when I switched off and start is wark but it's keep many times like this

@forkliftgeek10

4 жыл бұрын

Check for voltage and ground going to the solenoid when the code is present. Probably a bad connection since it is intermittent.

Ok nice

eXCUSEME.. I need help... what is EA5-1..? I haven't manual.. Can somebody help me?? My crane is 8FDu30

@forkliftgeek10

5 жыл бұрын

Seat switch is shorted.

Anyone know what error code 30 on a Heli series 18 means ?

What would be wrong with an electric Toyota forklift that will on drive in circles

@forkliftgeek10

3 жыл бұрын

That question is kinda vague. What model? 3 wheel? 4 wheel? You are not able to steer? Will only drive when turning?

Check parking brake switch

@forkliftgeek10

5 жыл бұрын

If the parking brake was used to disable drive, there would be no movement in both direction.

Hey have a 7fgu15 sometimes go forward reverse sometimes go on reverse but shifting on foward when you raise rpm is any idea to help

@forkliftgeek10

4 жыл бұрын

Check directional switch and relays.

you went the excess way to diagnose......just apply direction switch and test at the 2 wire for signal......done!

@mikesecondo2284

7 жыл бұрын

After being in the lift truck repair business for 30 years as well as being a factory training representative I don't KNOW what I am talking about!!

@forkliftgeek10

7 жыл бұрын

+Mike Secondo Lol.

@daviebradley2276

7 жыл бұрын

I have signal and new solenoids and switch checks out ok losing forward some times and others lose reverse any suggestions

@FastBubbaRcing17

7 жыл бұрын

Davie Bradley could be the seat switch.

@samuelw.3992

Жыл бұрын

@@FastBubbaRcing17it wouldn’t start then

What if I went I put juice to the T pin and it still doesn't go forward ?

@forkliftgeek10

7 жыл бұрын

+Quincy Abrams I would check if there is good ground. From there the next step for me is taking pressure readings from the valve body.

I dont believe to much sometimes it happen in fuse base on my experienced.

@samuelw.3992

Жыл бұрын

I’ve even had fuses that weren’t blown be bad, no joke.

Hello how are you, I would like to know what the problem was, since I do not speak English and use a translator, and what you say at the end of the video does not translate it to me, thank you

I have a problem with my yale 2011 4 tn, doesnt drive reverse. Do i have to do the same? or how does this change, do i need the electric diagram? thanks

@forkliftgeek10

7 жыл бұрын

+Aldo Morales sorry bro but I'm not familiar with Yale trucks. But I would start with the reverse switch if it has any. Schematic would always help.

@rishabhshuklafanclub2316

Жыл бұрын

How you are solved your problem

Hi I have Toyota 7FBH20 Forklift but when accelerator presse so not working lifting Disconnected pump drive motor or not showing error can you help me sir.

@forkliftgeek10

6 жыл бұрын

+0580122013 ibrar if it powers up and there is no drive or lift and you dont have code on diaplay then i would check seat switch first.

@muhammadibrar8798

6 жыл бұрын

Sir not showing error code I was checking all connection one by one .and also I will change CPU bord and accelerator switch but same problem sir ..battery forklift 7FBH20.....

@forkliftgeek10

6 жыл бұрын

+0580122013 ibrar check seat switch

out of curiosity, where are the t/c relays located? are they inside of the black box behind the left step?

@forkliftgeek10

8 жыл бұрын

Yes

@mattperkins7038

8 жыл бұрын

+ForkliftGeek I've got one that doesn't have forward. I put battery volts to that connector at the transmission and still no luck. so I replaced the solenoid. still nada. I verified I have switched voltage at the connection. there's no possible way the relay would be bad if I have all of those things, correct? I found a plug for the forward valve broken, but I could still freely move the valve in the bore and the valve would spring back like it should. all of this after a pm. go figure. any thoughts? btw your videos are very informative...even to veteran lift techs. keep up the good work

@forkliftgeek10

8 жыл бұрын

Is it the same color wires as in this video?

@forkliftgeek10

8 жыл бұрын

I think some of these have 4 wires in the connector instead of two. Two wires mean the solenoid is grounded to the body if four then the other two would be ground wires for each solenoid. The most effective way is to use a scope to look at the current and voltage to see if the solenoid is really opening and closing. Using a current clamp and comparing the current to the reverse would give an idea if the solenoid is operating. If the solenoid is shifting the spool, then pressure tests would be my next step.

@forkliftgeek10

8 жыл бұрын

Oh and thanks for the nice comment Matt.

Hi any ideas why my 3fd15 toyota has no drive?

@forkliftgeek10

6 жыл бұрын

+Mark Scott check directional lever, spool and inching pedal.

I have a problem with my Toyota forklift if it keeps bogging and it dies out trying to lift stuff or we driving Ford can someone help me please

@forkliftgeek10

8 жыл бұрын

without much info, I would start with ignition. also if you know how to use a vacuum gauge, check to see if your engine is breathing properly.

I have a lift just like this.... my accelerator pedal does not function.... what could that be???

@forkliftgeek10

7 жыл бұрын

+Rene Trevino do you mean the engine does not Rev up when you step on the pedal?

@TheRtrevino25

7 жыл бұрын

ForkliftGeek yeah.... I don't know what part controls that function...

@forkliftgeek10

7 жыл бұрын

+Rene Trevino well, if your truck is exactly like the one in this video then it could be a cope of things. One could be the accelerator potentiometer, the electronic throttle body, or it could be that the computer is not allowing the engine to Rev up because it sees a fault (limp mode).

@TheRtrevino25

7 жыл бұрын

ForkliftGeek cool thank you... how would I know if its in limo mode for sure.. and how could I reset it....

@forkliftgeek10

7 жыл бұрын

+Rene Trevino the MIL would be lit, it would start and idle but would not accelerate. There is no reset for limp mode until the problem is fixed.

Gair not work not going back

You need help other guy for hold camera,

Cómo pasarlo a español

So what was the problem any conclution?????

@forkliftgeek10

6 жыл бұрын

+Luis Elias directional switch

@BlackSkuLL4u2

6 жыл бұрын

The forklift im dealing with is stuck on revers ima try to throw 12v straight up to the foward selenoid to see what it dose what do u think brother

@forkliftgeek10

6 жыл бұрын

+Luis Elias applying 12v to the fwd solenoid would not make a difference if its stuck in reverse.

@BlackSkuLL4u2

6 жыл бұрын

Really bro dam i dont know what to do any ideas?

@forkliftgeek10

6 жыл бұрын

+Luis Elias when u say its stuck in reverse do u mean it just drives in reverse and not forward? Or just drives in reverse no matter what direction u choose.

Great video. Ihave the 7FG15 GENEO SAS and my screen is not working.help!!

@forkliftgeek10

4 жыл бұрын

If it's just the screen, then check power to it from key switch also check for negative supply other than that it's the screen itself.

How can I check bypass test. Could anyone please tell me. Bcoz I struggle with the same problem

Hello how are you

I have a problem my Toyota 5bcu25 forklifter when i s/w on every things r oky but forklifter not move forwed&back giving problem on front secreen CO

@forkliftgeek10

8 жыл бұрын

+Shabbir Hussain code CO is drive circuit abnormality fault. Everything concerning the drive circuit is suspect, but I'd start by checking the motor brushes.

@forkliftgeek10

8 жыл бұрын

+Shabbir Hussain code CO is drive circuit abnormality fault. Everything concerning the drive circuit is suspect, but I'd start by checking the motor brushes.

Good 👍🏻